Hi Adrien,
thanks for the patch. I've made only a few comments inline.
On 21-01-18 12:15, Adrien Grassein wrote:
> Tested with a basic Build Root configuration booting from sdcard.
>
> Signed-off-by: Adrien Grassein <adrien.grassein@xxxxxxxxx>
> Reviewed-by: Krzysztof Kozlowski <krzk@xxxxxxxxxx>
> ---
> arch/arm64/boot/dts/freescale/Makefile | 1 +
> .../dts/freescale/imx8mm-nitrogen8mm_rev2.dts | 395 ++++++++++++++++++
> 2 files changed, 396 insertions(+)
> create mode 100644 arch/arm64/boot/dts/freescale/imx8mm-nitrogen8mm_rev2.dts
>
> diff --git a/arch/arm64/boot/dts/freescale/Makefile b/arch/arm64/boot/dts/freescale/Makefile
> index 38559943c15d..398b5cb4f3e2 100644
> --- a/arch/arm64/boot/dts/freescale/Makefile
> +++ b/arch/arm64/boot/dts/freescale/Makefile
> @@ -49,6 +49,7 @@ dtb-$(CONFIG_ARCH_MXC) += imx8mq-librem5-devkit.dtb
> dtb-$(CONFIG_ARCH_MXC) += imx8mq-librem5-r2.dtb
> dtb-$(CONFIG_ARCH_MXC) += imx8mq-librem5-r3.dtb
> dtb-$(CONFIG_ARCH_MXC) += imx8mq-nitrogen.dtb
> +dtb-$(CONFIG_ARCH_MXC) += imx8mm-nitrogen8mm_rev2.dtb
> dtb-$(CONFIG_ARCH_MXC) += imx8mq-phanbell.dtb
> dtb-$(CONFIG_ARCH_MXC) += imx8mq-pico-pi.dtb
> dtb-$(CONFIG_ARCH_MXC) += imx8mq-thor96.dtb
> diff --git a/arch/arm64/boot/dts/freescale/imx8mm-nitrogen8mm_rev2.dts b/arch/arm64/boot/dts/freescale/imx8mm-nitrogen8mm_rev2.dts
> new file mode 100644
> index 000000000000..755088387ea5
> --- /dev/null
> +++ b/arch/arm64/boot/dts/freescale/imx8mm-nitrogen8mm_rev2.dts
> @@ -0,0 +1,395 @@
> +// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
> +/*
> + * Device Tree file for Boundary Devices i.MX8MMini Nitrogen8MM Rev2 board.
> + * Adrien Grassein <adrien.grassein@xxxxxxxxxxxxx>
> + */
> +/dts-v1/;
> +#include "imx8mm.dtsi"
> +
> +/ {
> + model = "Boundary Devices i.MX8MMini Nitrogen8MM Rev2";
> + compatible = "boundary,imx8mm-nitrogen8mm", "fsl,imx8mm";
> +};
> +
> +&A53_0 {
> + cpu-supply = <®_sw3>;
> +};
> +
> +&A53_1 {
> + cpu-supply = <®_sw3>;
> +};
> +
> +&A53_2 {
> + cpu-supply = <®_sw3>;
> +};
> +
> +&A53_3 {
> + cpu-supply = <®_sw3>;
> +};
> +
> +&fec1 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_fec1>;
> + phy-mode = "rgmii-id";
> + phy-handle = <ðphy0>;
> + fsl,magic-packet;
> + status = "okay";
> +
> + mdio {
> + #address-cells = <1>;
> + #size-cells = <0>;
> +
> + ethphy0: ethernet-phy@4 {
> + compatible = "ethernet-phy-id004d.d072",
^
Do we really need to add the id here?
> + "ethernet-phy-ieee802.3-c22";
> + reg = <4>;
> + interrupts-extended = <&gpio3 16 IRQ_TYPE_LEVEL_LOW>;
> + };
> + };
> +};
> +
> +&i2c1 {
> + clock-frequency = <400000>;
^
Is the i2c errata fixed on the imx8?
> + pinctrl-names = "default", "gpio";
^
no pinctrl for gpio.
> + pinctrl-0 = <&pinctrl_i2c1>;
> + status = "okay";
> +
> + pmic@8 {
> + compatible = "nxp,pf8121a";
> + reg = <0x8>;
> +
> + regulators {
> + reg_ldo1: ldo1 {
^
alignment
> + regulator-min-microvolt = <1500000>;
> + regulator-max-microvolt = <5000000>;
> + regulator-boot-on;
> + regulator-always-on;
> + };
> +
> + reg_ldo2: ldo2 {
> + regulator-min-microvolt = <1500000>;
> + regulator-max-microvolt = <5000000>;
> + regulator-boot-on;
> + regulator-always-on;
> + };
> +
> + reg_ldo3: ldo3 {
> + regulator-min-microvolt = <1500000>;
> + regulator-max-microvolt = <5000000>;
> + regulator-boot-on;
> + regulator-always-on;
> + };
> +
> + reg_ldo4: ldo4 {
> + regulator-min-microvolt = <1500000>;
> + regulator-max-microvolt = <5000000>;
> + regulator-boot-on;
> + regulator-always-on;
> + };
> +
> + reg_buck1: buck1 {
> + regulator-min-microvolt = <400000>;
> + regulator-max-microvolt = <1800000>;
> + regulator-boot-on;
> + regulator-always-on;
> + };
> +
> + reg_buck2: buck2 {
> + regulator-min-microvolt = <400000>;
> + regulator-max-microvolt = <1800000>;
> + regulator-boot-on;
> + regulator-always-on;
> + };
> +
> + reg_sw3: buck3 {
> + regulator-min-microvolt = <400000>;
> + regulator-max-microvolt = <1800000>;
> + regulator-boot-on;
> + regulator-always-on;
> + };
> +
> + reg_buck4: buck4 {
> + regulator-min-microvolt = <400000>;
> + regulator-max-microvolt = <1800000>;
> + regulator-boot-on;
> + regulator-always-on;
> + };
> +
> + reg_buck5: buck5 {
> + regulator-min-microvolt = <400000>;
> + regulator-max-microvolt = <1800000>;
> + regulator-boot-on;
> + regulator-always-on;
> + };
> +
> + reg_buck6: buck6 {
> + regulator-min-microvolt = <400000>;
> + regulator-max-microvolt = <1800000>;
> + regulator-boot-on;
> + regulator-always-on;
> + };
> +
> + reg_buck7: buck7 {
> + regulator-min-microvolt = <3300000>;
> + regulator-max-microvolt = <3300000>;
> + regulator-boot-on;
> + regulator-always-on;
> + };
> +
> + reg_vsnvs: vsnvs {
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <3300000>;
> + regulator-boot-on;
> + regulator-always-on;
> + };
Do we really need to have all regulators marked as always-on?
> + };
> + };
> +};
> +
> +&i2c3 {
> + clock-frequency = <100000>;
> + pinctrl-names = "default", "gpio";
> + pinctrl-0 = <&pinctrl_i2c3>;
> + status = "okay";
> +
> + i2cmux@70 {
> + compatible = "nxp,pca9540";
> + reg = <0x70>;
> + #address-cells = <1>;
> + #size-cells = <0>;
> +
> + i2c3 {
> + reg = <0>;
> + #address-cells = <1>;
> + #size-cells = <0>;
> +
> + rtc@68 {
> + compatible = "microcrystal,rv4162";
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_i2c3a_rv4162>;
> + reg = <0x68>;
reg should be the 2nd property, after the compatible.
> + interrupts-extended = <&gpio4 22 IRQ_TYPE_LEVEL_LOW>;
> + wakeup-source;
> + };
> + };
> + };
> +};
> +
> +/* console */
> +&uart2 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_uart2>;
> + assigned-clocks = <&clk IMX8MM_CLK_UART2>;
> + assigned-clock-parents = <&clk IMX8MM_CLK_24M>;
> + status = "okay";
> +};
> +
> +/* eMMC */
> +&usdhc1 {
> + bus-width = <8>;
> + sdhci-caps-mask = <0x80000000 0x0>;
^
This is a SD host controller property according the doc.
> + non-removable;
> + pinctrl-names = "default", "state_100mhz", "state_200mhz";
> + pinctrl-0 = <&pinctrl_usdhc1>;
> + pinctrl-1 = <&pinctrl_usdhc1_100mhz>;
> + pinctrl-2 = <&pinctrl_usdhc1_200mhz>;
> + status = "okay";
> +};
> +
> +/* sdcard */
> +&usdhc2 {
> + bus-width = <4>;
> + cd-gpios = <&gpio2 12 GPIO_ACTIVE_LOW>;
> + pinctrl-names = "default", "state_100mhz", "state_200mhz";
> + pinctrl-0 = <&pinctrl_usdhc2>;
> + pinctrl-1 = <&pinctrl_usdhc2_100mhz>;
> + pinctrl-2 = <&pinctrl_usdhc2_200mhz>;
> + vqmmc-supply = <®_ldo2>;
> + status = "okay";
> +};
> +
> +&wdog1 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_wdog>;
> + fsl,ext-reset-output;
> + status = "okay";
> +};
> +
> +&iomuxc {
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_hog>;
It would be nice to avoid such hog's. Instead those gpios should get
configured by the device(s) using those.
Regards,
Marco
> +
> + pinctrl_fec1: fec1grp {
> + fsl,pins = <
> + MX8MM_IOMUXC_ENET_MDC_ENET1_MDC 0x3
> + MX8MM_IOMUXC_ENET_MDIO_ENET1_MDIO 0x3
> + MX8MM_IOMUXC_ENET_TD3_ENET1_RGMII_TD3 0x1f
> + MX8MM_IOMUXC_ENET_TD2_ENET1_RGMII_TD2 0x1f
> + MX8MM_IOMUXC_ENET_TD1_ENET1_RGMII_TD1 0x1f
> + MX8MM_IOMUXC_ENET_TD0_ENET1_RGMII_TD0 0x1f
> + MX8MM_IOMUXC_ENET_RD3_ENET1_RGMII_RD3 0x91
> + MX8MM_IOMUXC_ENET_RD2_ENET1_RGMII_RD2 0x91
> + MX8MM_IOMUXC_ENET_RD1_ENET1_RGMII_RD1 0x91
> + MX8MM_IOMUXC_ENET_RD0_ENET1_RGMII_RD0 0x91
> + MX8MM_IOMUXC_ENET_TXC_ENET1_RGMII_TXC 0x1f
> + MX8MM_IOMUXC_ENET_RXC_ENET1_RGMII_RXC 0x91
> + MX8MM_IOMUXC_ENET_RX_CTL_ENET1_RGMII_RX_CTL 0x91
> + MX8MM_IOMUXC_ENET_TX_CTL_ENET1_RGMII_TX_CTL 0x1f
> + MX8MM_IOMUXC_NAND_READY_B_GPIO3_IO16 0x159
> + >;
> + };
> +
> + pinctrl_hog: hoggrp {
> + fsl,pins = <
> + MX8MM_IOMUXC_GPIO1_IO03_GPIO1_IO3 0x09
> + MX8MM_IOMUXC_GPIO1_IO08_GPIO1_IO8 0x09
> + >;
> + };
> +
> + pinctrl_i2c1: i2c1grp {
> + fsl,pins = <
> + MX8MM_IOMUXC_I2C1_SCL_I2C1_SCL 0x400001c3
> + MX8MM_IOMUXC_I2C1_SDA_I2C1_SDA 0x400001c3
> + >;
> + };
> +
> + pinctrl_i2c3: i2c3grp {
> + fsl,pins = <
> + MX8MM_IOMUXC_I2C3_SCL_I2C3_SCL 0x400001c3
> + MX8MM_IOMUXC_I2C3_SDA_I2C3_SDA 0x400001c3
> + >;
> + };
> +
> + pinctrl_i2c3a_rv4162: i2c3a-rv4162grp {
> + fsl,pins = <
> + MX8MM_IOMUXC_SAI2_RXC_GPIO4_IO22 0x1c0
> + >;
> + };
> +
> + pinctrl_uart2: uart2grp {
> + fsl,pins = <
> + MX8MM_IOMUXC_UART2_RXD_UART2_DCE_RX 0x140
> + MX8MM_IOMUXC_UART2_TXD_UART2_DCE_TX 0x140
> + >;
> + };
> +
> + pinctrl_usdhc1: usdhc1grp {
> + fsl,pins = <
> + MX8MM_IOMUXC_SD1_CLK_USDHC1_CLK 0x190
> + MX8MM_IOMUXC_SD1_CMD_USDHC1_CMD 0x1d0
> + MX8MM_IOMUXC_SD1_DATA0_USDHC1_DATA0 0x1d0
> + MX8MM_IOMUXC_SD1_DATA1_USDHC1_DATA1 0x1d0
> + MX8MM_IOMUXC_SD1_DATA2_USDHC1_DATA2 0x1d0
> + MX8MM_IOMUXC_SD1_DATA3_USDHC1_DATA3 0x1d0
> + MX8MM_IOMUXC_SD1_DATA4_USDHC1_DATA4 0x1d0
> + MX8MM_IOMUXC_SD1_DATA5_USDHC1_DATA5 0x1d0
> + MX8MM_IOMUXC_SD1_DATA6_USDHC1_DATA6 0x1d0
> + MX8MM_IOMUXC_SD1_DATA7_USDHC1_DATA7 0x1d0
> + MX8MM_IOMUXC_SD1_RESET_B_GPIO2_IO10 0x141
> + >;
> + };
> +
> + pinctrl_usdhc1_100mhz: usdhc1-100mhz-grp {
> + fsl,pins = <
> + MX8MM_IOMUXC_SD1_CLK_USDHC1_CLK 0x194
> + MX8MM_IOMUXC_SD1_CMD_USDHC1_CMD 0x1d4
> + MX8MM_IOMUXC_SD1_DATA0_USDHC1_DATA0 0x1d4
> + MX8MM_IOMUXC_SD1_DATA1_USDHC1_DATA1 0x1d4
> + MX8MM_IOMUXC_SD1_DATA2_USDHC1_DATA2 0x1d4
> + MX8MM_IOMUXC_SD1_DATA3_USDHC1_DATA3 0x1d4
> + MX8MM_IOMUXC_SD1_DATA4_USDHC1_DATA4 0x1d4
> + MX8MM_IOMUXC_SD1_DATA5_USDHC1_DATA5 0x1d4
> + MX8MM_IOMUXC_SD1_DATA6_USDHC1_DATA6 0x1d4
> + MX8MM_IOMUXC_SD1_DATA7_USDHC1_DATA7 0x1d4
> + >;
> + };
> +
> + pinctrl_usdhc1_200mhz: usdhc1-200mhz-grp {
> + fsl,pins = <
> + MX8MM_IOMUXC_SD1_CLK_USDHC1_CLK 0x196
> + MX8MM_IOMUXC_SD1_CMD_USDHC1_CMD 0x1d6
> + MX8MM_IOMUXC_SD1_DATA0_USDHC1_DATA0 0x1d6
> + MX8MM_IOMUXC_SD1_DATA1_USDHC1_DATA1 0x1d6
> + MX8MM_IOMUXC_SD1_DATA2_USDHC1_DATA2 0x1d6
> + MX8MM_IOMUXC_SD1_DATA3_USDHC1_DATA3 0x1d6
> + MX8MM_IOMUXC_SD1_DATA4_USDHC1_DATA4 0x1d6
> + MX8MM_IOMUXC_SD1_DATA5_USDHC1_DATA5 0x1d6
> + MX8MM_IOMUXC_SD1_DATA6_USDHC1_DATA6 0x1d6
> + MX8MM_IOMUXC_SD1_DATA7_USDHC1_DATA7 0x1d6
> + >;
> + };
> +
> + pinctrl_usdhc2: usdhc2grp {
> + fsl,pins = <
> + MX8MM_IOMUXC_SD2_CLK_USDHC2_CLK 0x190
> + MX8MM_IOMUXC_SD2_CMD_USDHC2_CMD 0x1d0
> + MX8MM_IOMUXC_SD2_DATA0_USDHC2_DATA0 0x1d0
> + MX8MM_IOMUXC_SD2_DATA1_USDHC2_DATA1 0x1d0
> + MX8MM_IOMUXC_SD2_DATA2_USDHC2_DATA2 0x1d0
> + MX8MM_IOMUXC_SD2_DATA3_USDHC2_DATA3 0x1d0
> + MX8MM_IOMUXC_SD2_CD_B_GPIO2_IO12 0x1c4
> + >;
> + };
> +
> + pinctrl_usdhc2_100mhz: usdhc2-100mhz-grp {
> + fsl,pins = <
> + MX8MM_IOMUXC_SD2_CLK_USDHC2_CLK 0x194
> + MX8MM_IOMUXC_SD2_CMD_USDHC2_CMD 0x1d4
> + MX8MM_IOMUXC_SD2_DATA0_USDHC2_DATA0 0x1d4
> + MX8MM_IOMUXC_SD2_DATA1_USDHC2_DATA1 0x1d4
> + MX8MM_IOMUXC_SD2_DATA2_USDHC2_DATA2 0x1d4
> + MX8MM_IOMUXC_SD2_DATA3_USDHC2_DATA3 0x1d4
> + >;
> + };
> +
> + pinctrl_usdhc2_200mhz: usdhc2-200mhz-grp {
> + fsl,pins = <
> + MX8MM_IOMUXC_SD2_CLK_USDHC2_CLK 0x196
> + MX8MM_IOMUXC_SD2_CMD_USDHC2_CMD 0x1d6
> + MX8MM_IOMUXC_SD2_DATA0_USDHC2_DATA0 0x1d6
> + MX8MM_IOMUXC_SD2_DATA1_USDHC2_DATA1 0x1d6
> + MX8MM_IOMUXC_SD2_DATA2_USDHC2_DATA2 0x1d6
> + MX8MM_IOMUXC_SD2_DATA3_USDHC2_DATA3 0x1d6
> + >;
> + };
> +
> + pinctrl_usdhc3: usdhc3grp {
> + fsl,pins = <
> + MX8MM_IOMUXC_NAND_WE_B_USDHC3_CLK 0x190
> + MX8MM_IOMUXC_NAND_WP_B_USDHC3_CMD 0x1d0
> + MX8MM_IOMUXC_NAND_DATA04_USDHC3_DATA0 0x1d0
> + MX8MM_IOMUXC_NAND_DATA05_USDHC3_DATA1 0x1d0
> + MX8MM_IOMUXC_NAND_DATA06_USDHC3_DATA2 0x1d0
> + MX8MM_IOMUXC_NAND_DATA07_USDHC3_DATA3 0x1d0
> + MX8MM_IOMUXC_GPIO1_IO00_ANAMIX_REF_CLK_32K 0x03
> + >;
> + };
> +
> + pinctrl_usdhc3_100mhz: usdhc3-100mhz-grp {
> + fsl,pins = <
> + MX8MM_IOMUXC_NAND_WE_B_USDHC3_CLK 0x194
> + MX8MM_IOMUXC_NAND_WP_B_USDHC3_CMD 0x1d4
> + MX8MM_IOMUXC_NAND_DATA04_USDHC3_DATA0 0x1d4
> + MX8MM_IOMUXC_NAND_DATA05_USDHC3_DATA1 0x1d4
> + MX8MM_IOMUXC_NAND_DATA06_USDHC3_DATA2 0x1d4
> + MX8MM_IOMUXC_NAND_DATA07_USDHC3_DATA3 0x1d4
> + >;
> + };
> +
> + pinctrl_usdhc3_200mhz: usdhc3-200mhz-grp {
> + fsl,pins = <
> + MX8MM_IOMUXC_NAND_WE_B_USDHC3_CLK 0x196
> + MX8MM_IOMUXC_NAND_WP_B_USDHC3_CMD 0x1d6
> + MX8MM_IOMUXC_NAND_DATA04_USDHC3_DATA0 0x1d6
> + MX8MM_IOMUXC_NAND_DATA05_USDHC3_DATA1 0x1d6
> + MX8MM_IOMUXC_NAND_DATA06_USDHC3_DATA2 0x1d6
> + MX8MM_IOMUXC_NAND_DATA07_USDHC3_DATA3 0x1d6
> + >;
> + };
> +
> + pinctrl_wdog: wdoggrp {
> + fsl,pins = <
> + MX8MM_IOMUXC_GPIO1_IO02_WDOG1_WDOG_B 0x140
> + >;
> + };
> +};
> --
> 2.25.1
>
>
> _______________________________________________
> linux-arm-kernel mailing list
> linux-arm-kernel@xxxxxxxxxxxxxxxxxxx
> http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
>
--
Pengutronix e.K. | |
Steuerwalder Str. 21 | http://www.pengutronix.de/ |
31137 Hildesheim, Germany | Phone: +49-5121-206917-0 |
Amtsgericht Hildesheim, HRA 2686 | Fax: +49-5121-206917-5555 |
