On Wed, 2021-01-20 at 11:27 +0200, Laurentiu Palcu wrote: > Hi Liu Ying, > > On Wed, Jan 20, 2021 at 04:42:50PM +0800, Liu Ying wrote: > > Hi Laurentiu, > > > > On Fri, 2021-01-15 at 19:27 +0200, Laurentiu Palcu wrote: > > > Hi Liu Ying, > > > > > > I promised I would have a second, more in-depth, look at this and I finally > > > managed to do it. > > > > Thanks. > > > > > I have to admit it was a challenge. Partially because I'm not very familiar > > > with DPU but mostly because of the abundance of macros used. It's true, macros > > > make the code more compact. However they made the entire code hard to read, > > > as neither ctags nor cscope were able to cross-reference it properly, and I > > > fear it will be even harder to maintain in the long run... :/ For example, > > > trying to figure out where dpu_*_hw_init() functions were called from was no > > > easy task. Or dpu_*_put(). Or dpu_*_get(). :/ > > > > > > Also, most of the macros are not in-line with Linux Kernel coding > > > style when it comes to macro usage: they affect control flow and some depend > > > on other local variables being already defined. > > > > > > The good news is most macros can be replaced with helper functions and it would > > > not add too much extra code. > > > > Ok, I'll remove macros where possible. > > > > > More comments below. > > > > Please find feedbacks below. > > > > > On Fri, Dec 18, 2020 at 11:23:52AM +0800, Liu Ying wrote: > > > > This patch introduces i.MX8qm/qxp Display Processing Unit(DPU) DRM support. > > > > > > > > DPU is comprised of two main components that include a blit engine for > > > > 2D graphics accelerations(with composition support) and a display controller > > > > for display output processing, as well as a command sequencer. Outside of > > > > DPU, optional prefetch engines, a.k.a, Prefetch Resolve Gasket(PRG) and > > > > Display Prefetch Resolve(DPR), can fetch data from memory prior to some DPU > > > > fetchunits of blit engine and display controller. The prefetch engines > > > > support reading linear formats and resolving Vivante GPU tile formats. > > > > > > > > This patch adds kernel modesetting support for the display controller part. > > > > The driver supports two CRTCs per display controller, planes backed by > > > > four fetchunits(decode0/1, fetchlayer, fetchwarp), fetchunit allocation > > > > logic for the two CRTCs, prefetch engines(with tile resolving supported), > > > > plane upscaling/deinterlacing/yuv2rgb CSC/alpha blending and CRTC gamma > > > > correction. The registers of the controller is accessed without command > > > > sequencer involved, instead just by using CPU. > > > > > > > > Reference manual can be found at: > > > > https://www.nxp.com/webapp/Download?colCode=IMX8DQXPRM > > > > > > > > Signed-off-by: Liu Ying <victor.liu@xxxxxxx> > > > > --- > > > > v4->v5: > > > > * Rebase up onto the latest drm-misc-next branch and remove the hook to > > > > drm_atomic_helper_legacy_gamma_set(), because it was dropped by the newly > > > > landed commit 'drm: automatic legacy gamma support'. > > > > * Remove a redundant blank line from dpu_plane_atomic_update(). > > > > > > > > v3->v4: > > > > * No change. > > > > > > > > v2->v3: > > > > * Fix build warnings Reported-by: kernel test robot <lkp@xxxxxxxxx>. > > > > * Drop build dependency on IMX_SCU, as dummy SCU functions have been added in > > > > header files by the patch 'firmware: imx: add dummy functions' which has > > > > landed in linux-next/master branch. > > > > > > > > v1->v2: > > > > * Add compatible for i.MX8qm DPU, as this is tested with i.MX8qm LVDS displays. > > > > (Laurentiu) > > > > * Fix PRG burst size and stride. (Laurentiu) > > > > * Put 'ports' OF node to fix the bail-out logic in dpu_drm_probe(). (Laurentiu) > > > > > > > > drivers/gpu/drm/imx/Kconfig | 1 + > > > > drivers/gpu/drm/imx/Makefile | 1 + > > > > drivers/gpu/drm/imx/dpu/Kconfig | 10 + > > > > drivers/gpu/drm/imx/dpu/Makefile | 10 + > > > > drivers/gpu/drm/imx/dpu/dpu-constframe.c | 170 ++++++ > > > > drivers/gpu/drm/imx/dpu/dpu-core.c | 881 ++++++++++++++++++++++++++++ > > > > drivers/gpu/drm/imx/dpu/dpu-crtc.c | 925 ++++++++++++++++++++++++++++++ > > > > drivers/gpu/drm/imx/dpu/dpu-crtc.h | 62 ++ > > > > drivers/gpu/drm/imx/dpu/dpu-disengcfg.c | 114 ++++ > > > > drivers/gpu/drm/imx/dpu/dpu-dprc.c | 721 +++++++++++++++++++++++ > > > > drivers/gpu/drm/imx/dpu/dpu-dprc.h | 40 ++ > > > > drivers/gpu/drm/imx/dpu/dpu-drv.c | 297 ++++++++++ > > > > drivers/gpu/drm/imx/dpu/dpu-drv.h | 28 + > > > > drivers/gpu/drm/imx/dpu/dpu-extdst.c | 296 ++++++++++ > > > > drivers/gpu/drm/imx/dpu/dpu-fetchdecode.c | 291 ++++++++++ > > > > drivers/gpu/drm/imx/dpu/dpu-fetcheco.c | 221 +++++++ > > > > drivers/gpu/drm/imx/dpu/dpu-fetchlayer.c | 151 +++++ > > > > drivers/gpu/drm/imx/dpu/dpu-fetchunit.c | 609 ++++++++++++++++++++ > > > > drivers/gpu/drm/imx/dpu/dpu-fetchunit.h | 191 ++++++ > > > > drivers/gpu/drm/imx/dpu/dpu-fetchwarp.c | 247 ++++++++ > > > > drivers/gpu/drm/imx/dpu/dpu-framegen.c | 392 +++++++++++++ > > > > drivers/gpu/drm/imx/dpu/dpu-gammacor.c | 220 +++++++ > > > > drivers/gpu/drm/imx/dpu/dpu-hscaler.c | 272 +++++++++ > > > > drivers/gpu/drm/imx/dpu/dpu-kms.c | 543 ++++++++++++++++++ > > > > drivers/gpu/drm/imx/dpu/dpu-kms.h | 23 + > > > > drivers/gpu/drm/imx/dpu/dpu-layerblend.c | 345 +++++++++++ > > > > drivers/gpu/drm/imx/dpu/dpu-plane.c | 702 +++++++++++++++++++++++ > > > > drivers/gpu/drm/imx/dpu/dpu-plane.h | 56 ++ > > > > drivers/gpu/drm/imx/dpu/dpu-prg.c | 433 ++++++++++++++ > > > > drivers/gpu/drm/imx/dpu/dpu-prg.h | 45 ++ > > > > drivers/gpu/drm/imx/dpu/dpu-prv.h | 203 +++++++ > > > > drivers/gpu/drm/imx/dpu/dpu-tcon.c | 249 ++++++++ > > > > drivers/gpu/drm/imx/dpu/dpu-vscaler.c | 305 ++++++++++ > > > > drivers/gpu/drm/imx/dpu/dpu.h | 389 +++++++++++++ > > > > 34 files changed, 9443 insertions(+) > > > > create mode 100644 drivers/gpu/drm/imx/dpu/Kconfig > > > > create mode 100644 drivers/gpu/drm/imx/dpu/Makefile > > > > create mode 100644 drivers/gpu/drm/imx/dpu/dpu-constframe.c > > > > create mode 100644 drivers/gpu/drm/imx/dpu/dpu-core.c > > > > create mode 100644 drivers/gpu/drm/imx/dpu/dpu-crtc.c > > > > create mode 100644 drivers/gpu/drm/imx/dpu/dpu-crtc.h > > > > create mode 100644 drivers/gpu/drm/imx/dpu/dpu-disengcfg.c > > > > create mode 100644 drivers/gpu/drm/imx/dpu/dpu-dprc.c > > > > create mode 100644 drivers/gpu/drm/imx/dpu/dpu-dprc.h > > > > create mode 100644 drivers/gpu/drm/imx/dpu/dpu-drv.c > > > > create mode 100644 drivers/gpu/drm/imx/dpu/dpu-drv.h > > > > create mode 100644 drivers/gpu/drm/imx/dpu/dpu-extdst.c > > > > create mode 100644 drivers/gpu/drm/imx/dpu/dpu-fetchdecode.c > > > > create mode 100644 drivers/gpu/drm/imx/dpu/dpu-fetcheco.c > > > > create mode 100644 drivers/gpu/drm/imx/dpu/dpu-fetchlayer.c > > > > create mode 100644 drivers/gpu/drm/imx/dpu/dpu-fetchunit.c > > > > create mode 100644 drivers/gpu/drm/imx/dpu/dpu-fetchunit.h > > > > create mode 100644 drivers/gpu/drm/imx/dpu/dpu-fetchwarp.c > > > > create mode 100644 drivers/gpu/drm/imx/dpu/dpu-framegen.c > > > > create mode 100644 drivers/gpu/drm/imx/dpu/dpu-gammacor.c > > > > create mode 100644 drivers/gpu/drm/imx/dpu/dpu-hscaler.c > > > > create mode 100644 drivers/gpu/drm/imx/dpu/dpu-kms.c > > > > create mode 100644 drivers/gpu/drm/imx/dpu/dpu-kms.h > > > > create mode 100644 drivers/gpu/drm/imx/dpu/dpu-layerblend.c > > > > create mode 100644 drivers/gpu/drm/imx/dpu/dpu-plane.c > > > > create mode 100644 drivers/gpu/drm/imx/dpu/dpu-plane.h > > > > create mode 100644 drivers/gpu/drm/imx/dpu/dpu-prg.c > > > > create mode 100644 drivers/gpu/drm/imx/dpu/dpu-prg.h > > > > create mode 100644 drivers/gpu/drm/imx/dpu/dpu-prv.h > > > > create mode 100644 drivers/gpu/drm/imx/dpu/dpu-tcon.c > > > > create mode 100644 drivers/gpu/drm/imx/dpu/dpu-vscaler.c > > > > create mode 100644 drivers/gpu/drm/imx/dpu/dpu.h > > > > > > > > > > [...] > > > > > > > diff --git a/drivers/gpu/drm/imx/dpu/dpu-core.c b/drivers/gpu/drm/imx/dpu/dpu-core.c > > > > new file mode 100644 > > > > index 00000000..52224ae > > > > --- /dev/null > > > > +++ b/drivers/gpu/drm/imx/dpu/dpu-core.c > > > > @@ -0,0 +1,881 @@ > > > > +// SPDX-License-Identifier: GPL-2.0+ > > > > + > > > > +/* > > > > + * Copyright (C) 2016 Freescale Semiconductor, Inc. > > > > + * Copyright 2017-2020 NXP > > > > + */ > > > > + > > > > +#include <linux/dma-mapping.h> > > > > +#include <linux/io.h> > > > > +#include <linux/irq.h> > > > > +#include <linux/irqchip/chained_irq.h> > > > > +#include <linux/module.h> > > > > +#include <linux/of_device.h> > > > > +#include <linux/of_graph.h> > > > > +#include <linux/platform_device.h> > > > > +#include <linux/pm_domain.h> > > > > +#include <linux/pm_runtime.h> > > > > +#include <linux/sizes.h> > > > > + > > > > +#include "dpu.h" > > > > +#include "dpu-prv.h" > > > > + > > > > +static inline u32 dpu_comctrl_read(struct dpu_soc *dpu, unsigned int offset) > > > > +{ > > > > + return readl(dpu->comctrl_reg + offset); > > > > +} > > > > + > > > > +static inline void dpu_comctrl_write(struct dpu_soc *dpu, > > > > + unsigned int offset, u32 value) > > > > +{ > > > > + writel(value, dpu->comctrl_reg + offset); > > > > +} > > > > + > > > > +/* Constant Frame */ > > > > +static const unsigned int cf_ids[] = {0, 1, 4, 5}; > > > > +static const enum dpu_unit_type cf_types[] = {DPU_DISP, DPU_DISP, > > > > + DPU_DISP, DPU_DISP}; > > > > +static const unsigned long cf_ofss[] = {0x4400, 0x5400, 0x4c00, 0x5c00}; > > > > +static const unsigned long cf_pec_ofss[] = {0x960, 0x9e0, 0x9a0, 0xa20}; > > > > + > > > > +/* Display Engine Configuration */ > > > > +static const unsigned int dec_ids[] = {0, 1}; > > > > +static const enum dpu_unit_type dec_types[] = {DPU_DISP, DPU_DISP}; > > > > +static const unsigned long dec_ofss[] = {0xb400, 0xb420}; > > > > + > > > > +/* External Destination */ > > > > +static const unsigned int ed_ids[] = {0, 1, 4, 5}; > > > > +static const enum dpu_unit_type ed_types[] = {DPU_DISP, DPU_DISP, > > > > + DPU_DISP, DPU_DISP}; > > > > +static const unsigned long ed_ofss[] = {0x4800, 0x5800, 0x5000, 0x6000}; > > > > +static const unsigned long ed_pec_ofss[] = {0x980, 0xa00, 0x9c0, 0xa40}; > > > > + > > > > +/* Fetch Decode */ > > > > +static const unsigned int fd_ids[] = {0, 1, 9}; > > > > +static const enum dpu_unit_type fd_types[] = {DPU_DISP, DPU_DISP, DPU_BLIT}; > > > > +static const unsigned long fd_ofss[] = {0x6c00, 0x7800, 0x1000}; > > > > +static const unsigned long fd_pec_ofss[] = {0xa80, 0xaa0, 0x820}; > > > > + > > > > +/* Fetch ECO */ > > > > +static const unsigned int fe_ids[] = {0, 1, 2, 9}; > > > > +static const enum dpu_unit_type fe_types[] = {DPU_DISP, DPU_DISP, > > > > + DPU_DISP, DPU_BLIT}; > > > > +static const unsigned long fe_ofss[] = {0x7400, 0x8000, 0x6800, 0x1c00}; > > > > +static const unsigned long fe_pec_ofss[] = {0xa90, 0xab0, 0xa70, 0x850}; > > > > + > > > > +/* Frame Generator */ > > > > +static const unsigned int fg_ids[] = {0, 1}; > > > > +static const enum dpu_unit_type fg_types[] = {DPU_DISP, DPU_DISP}; > > > > +static const unsigned long fg_ofss[] = {0xb800, 0xd400}; > > > > + > > > > +/* Fetch Layer */ > > > > +static const unsigned int fl_ids[] = {0}; > > > > +static const enum dpu_unit_type fl_types[] = {DPU_DISP}; > > > > +static const unsigned long fl_ofss[] = {0x8400}; > > > > +static const unsigned long fl_pec_ofss[] = {0xac0}; > > > > + > > > > +/* Fetch Warp */ > > > > +static const unsigned int fw_ids[] = {2, 9}; > > > > +static const enum dpu_unit_type fw_types[] = {DPU_DISP, DPU_BLIT}; > > > > +static const unsigned long fw_ofss[] = {0x6400, 0x1800}; > > > > +static const unsigned long fw_pec_ofss[] = {0xa60, 0x840}; > > > > + > > > > +/* Gamma Correction */ > > > > +static const unsigned int gc_ids[] = {0, 1}; > > > > +static const enum dpu_unit_type gc_types[] = {DPU_DISP, DPU_DISP}; > > > > +static const unsigned long gc_ofss[] = {0xc000, 0xdc00}; > > > > + > > > > +/* Horizontal Scaler */ > > > > +static const unsigned int hs_ids[] = {4, 5, 9}; > > > > +static const enum dpu_unit_type hs_types[] = {DPU_DISP, DPU_DISP, DPU_BLIT}; > > > > +static const unsigned long hs_ofss[] = {0x9000, 0x9c00, 0x3000}; > > > > +static const unsigned long hs_pec_ofss[] = {0xb00, 0xb60, 0x8c0}; > > > > + > > > > +/* Layer Blend */ > > > > +static const unsigned int lb_ids[] = {0, 1, 2, 3}; > > > > +static const enum dpu_unit_type lb_types[] = {DPU_DISP, DPU_DISP, > > > > + DPU_DISP, DPU_DISP}; > > > > +static const unsigned long lb_ofss[] = {0xa400, 0xa800, 0xac00, 0xb000}; > > > > +static const unsigned long lb_pec_ofss[] = {0xba0, 0xbc0, 0xbe0, 0xc00}; > > > > + > > > > +/* Timing Controller */ > > > > +static const unsigned int tcon_ids[] = {0, 1}; > > > > +static const enum dpu_unit_type tcon_types[] = {DPU_DISP, DPU_DISP}; > > > > +static const unsigned long tcon_ofss[] = {0xc800, 0xe400}; > > > > + > > > > +/* Vertical Scaler */ > > > > +static const unsigned int vs_ids[] = {4, 5, 9}; > > > > +static const enum dpu_unit_type vs_types[] = {DPU_DISP, DPU_DISP, DPU_BLIT}; > > > > +static const unsigned long vs_ofss[] = {0x9400, 0xa000, 0x3400}; > > > > +static const unsigned long vs_pec_ofss[] = {0xb20, 0xb80, 0x8e0}; > > > > + > > > > +#define DPU_UNITS_DEFINE(unit) \ > > > > +static const struct dpu_units dpu_##unit##s = { \ > > > > + .ids = unit##_ids, \ > > > > + .types = unit##_types, \ > > > > + .ofss = unit##_ofss, \ > > > > + .pec_ofss = unit##_pec_ofss, \ > > > > + .cnt = ARRAY_SIZE(unit##_ids), \ > > > > +} > > > > + > > > > +/* units without Pixel Engine Configuration */ > > > > +#define DPU_UNITS_DEFINE_NO_PEC(unit) \ > > > > +static const struct dpu_units dpu_##unit##s = { \ > > > > + .ids = unit##_ids, \ > > > > + .types = unit##_types, \ > > > > + .ofss = unit##_ofss, \ > > > > + .pec_ofss = NULL, \ > > > > + .cnt = ARRAY_SIZE(unit##_ids), \ > > > > +} > > > > + > > > > +DPU_UNITS_DEFINE(cf); > > > > +DPU_UNITS_DEFINE_NO_PEC(dec); > > > > +DPU_UNITS_DEFINE(ed); > > > > +DPU_UNITS_DEFINE(fd); > > > > +DPU_UNITS_DEFINE(fe); > > > > +DPU_UNITS_DEFINE_NO_PEC(fg); > > > > +DPU_UNITS_DEFINE(fl); > > > > +DPU_UNITS_DEFINE(fw); > > > > +DPU_UNITS_DEFINE_NO_PEC(gc); > > > > +DPU_UNITS_DEFINE(hs); > > > > +DPU_UNITS_DEFINE(lb); > > > > +DPU_UNITS_DEFINE_NO_PEC(tcon); > > > > +DPU_UNITS_DEFINE(vs); > > > > > > Wouldn't it be better if you defined the unit structures directly? Like below? > > > > > > static const struct dpu_units dpu_cfs = { > > > .ids = {0, 1, 4, 5}, > > > .types = {DPU_DISP, DPU_DISP, DPU_DISP, DPU_DISP}, > > > .ofss = {0x4400, 0x5400, 0x4c00, 0x5c00}, > > > .pec_ofss = {0x960, 0x9e0, 0x9a0, 0xa20}, > > > .cnt = 4, > > > }; > > > > With this, complier generates build warnings like this: > > > > drivers/gpu/drm/imx/dpu/dpu-core.c:36:2: warning: braces around scalar > > initializer > > .ids = {0, 1, 4, 5}, > > ^ > > drivers/gpu/drm/imx/dpu/dpu-core.c:36:2: note: (near initialization for > > ?dpu_cfs.ids?) > > drivers/gpu/drm/imx/dpu/dpu-core.c:36:13: warning: excess elements in > > scalar initializer > > .ids = {0, 1, 4, 5}, > > ^ > > ids, types, ofss and pec_ofss entries should be pure pointers instead > > of scalars, because struct dpu_units covers all DPU units which have > > various numbers of instances. > > I guess my suggestion would work if dpu_units would be declared like: > > struct dpu_units { > const unsigned int ids[4]; > const enum dpu_unit_type types[4]; > const unsigned long ofss[4]; > const unsigned long pec_ofss[4]; > const unsigned int cnt; > }; > > With 'cnt' you'd still be able to control the number of units present. > Also, I saw that the maximum is 4. Can there be more? Should be no more. > > Anyway, up to you if you still want to have individual arrays for ids, > types, etc. I prone to my way, because the sizes of individual arrays reflect real numbers of DPU units, which means a bit less memory size. Regards, Liu Ying > > Thanks, > laurentiu > > > > I guess dpu_units structure definition would need to change too. But this would > > > help get rid of cf_ids[], cf_types[], cf_ofss[], cf_pec_ofss[], etc. Also, no > > > > Due to the above explainations, it looks that this part of struct > > dpu_units definition cannot be changed and the arrays are needed. > > > > > need for macros. > > > > Will drop the macros. > > > > > > + > > > > +static void dpu_detach_pm_domains(struct dpu_soc *dpu) > > > > +{ > > > > +#define DPU_DETACH_PM_DOMAIN(name) \ > > > > +do { \ > > > > + if (!IS_ERR_OR_NULL(dpu->pd_##name##_link)) \ > > > > + device_link_del(dpu->pd_##name##_link); \ > > > > + if (!IS_ERR_OR_NULL(dpu->pd_##name##_dev)) \ > > > > + dev_pm_domain_detach(dpu->pd_##name##_dev, true); \ > > > > + \ > > > > + dpu->pd_##name##_dev = NULL; \ > > > > + dpu->pd_##name##_link = NULL; \ > > > > +} while (0) > > > > > > The above macro could go into a separate function: > > > > > > ~~~ > > > static void dpu_detach_pm_domain(struct device **pd_dev, > > > struct device_link **pd_link) > > > { > > > if (!IS_ERR_OR_NULL(*pd_link)) > > > device_link_del(*pd_link); > > > if (!IS_ERR_OR_NULL(*pd_dev)) > > > dev_pm_domain_detach(*pd_dev, true); > > > > > > *pd_dev = NULL; > > > *pd_link = NULL; > > > } > > > ~~~ > > > > > > > + > > > > + DPU_DETACH_PM_DOMAIN(pll1); > > > > + DPU_DETACH_PM_DOMAIN(pll0); > > > > + DPU_DETACH_PM_DOMAIN(dc); > > > > > > And instead of the macros, you could call the helper function directly: > > > > > > dpu_detach_pm_domain(&dpu->pd_pll1_dev, &dpu->pd_pll1_link); > > > dpu_detach_pm_domain(&dpu->pd_pll0_dev, &dpu->pd_pll0_link); > > > dpu_detach_pm_domain(&dpu->pd_dc_dev, &dpu->pd_dc_link); > > > > > > Wouldn't that be OK? > > > > Ok, will use functions. > > > > > > +} > > > > + > > > > +static int dpu_attach_pm_domains(struct dpu_soc *dpu) > > > > +{ > > > > + u32 flags = DL_FLAG_STATELESS | DL_FLAG_PM_RUNTIME | DL_FLAG_RPM_ACTIVE; > > > > + int ret = 0; > > > > + > > > > +#define DPU_ATTACH_PM_DOMAIN(name) \ > > > > +do { \ > > > > + dpu->pd_##name##_dev = \ > > > > + dev_pm_domain_attach_by_name(dpu->dev, "" #name ""); \ > > > > + if (IS_ERR(dpu->pd_##name##_dev)) { \ > > > > + ret = PTR_ERR(dpu->pd_##name##_dev); \ > > > > + dev_err(dpu->dev, \ > > > > + "failed to attach " #name " pd dev: %d\n", ret);\ > > > > + goto fail; \ > > > > + } \ > > > > + \ > > > > + dpu->pd_##name##_link = \ > > > > + device_link_add(dpu->dev, dpu->pd_##name##_dev, flags); \ > > > > + if (IS_ERR(dpu->pd_##name##_link)) { \ > > > > + ret = PTR_ERR(dpu->pd_##name##_link); \ > > > > + dev_err(dpu->dev, \ > > > > + "failed to add device link to " #name \ > > > > + " pd dev: %d\n", ret); \ > > > > + goto fail; \ > > > > + } \ > > > > +} while (0) > > > > > > This one should go into a separate function: > > > static int dpu_attach_pm_domain(struct dpu_soc *dpu, > > > struct device **pd_dev, > > > struct device_link **pd_link, > > > const char *name) > > > > > > > > > > + > > > > + DPU_ATTACH_PM_DOMAIN(dc); > > > > + DPU_ATTACH_PM_DOMAIN(pll0); > > > > + DPU_ATTACH_PM_DOMAIN(pll1); > > > > > > And these can call the helper functions directly: > > > ret = dpu_attach_pm_domain(dpu, &dpu->pd_dc_dev, &dpu->pd_dc_link, "dc"); > > > if (ret) > > > goto fail; > > > > > > Would this add too much code? > > > > Will use functions. > > > > > > + > > > > + return ret; > > > > +fail: > > > > + dpu_detach_pm_domains(dpu); > > > > + return ret; > > > > +} > > > > + > > > > +static void dpu_units_addr_dbg(struct dpu_soc *dpu, unsigned long dpu_base) > > > > +{ > > > > + int i; > > > > + > > > > + dev_dbg(dpu->dev, "Common Control: 0x%08lx\n", dpu_base); > > > > + > > > > +#define DPU_UNITS_ADDR_DBG(unit) \ > > > > +do { \ > > > > + const struct dpu_units *us = &dpu_##unit##s; \ > > > > + \ > > > > + for (i = 0; i < us->cnt; i++) { \ > > > > + if (us->pec_ofss) { \ > > > > + dev_dbg(dpu->dev, "%s%d: pixengcfg @ 0x%08lx," \ > > > > + " unit @ 0x%08lx\n", #unit, \ > > > > + us->ids[i], \ > > > > + dpu_base + us->pec_ofss[i], \ > > > > + dpu_base + us->ofss[i]); \ > > > > + } else { \ > > > > + dev_dbg(dpu->dev, \ > > > > + "%s%d: unit @ 0x%08lx\n", #unit, \ > > > > + us->ids[i], dpu_base + us->ofss[i]); \ > > > > + } \ > > > > + } \ > > > > +} while (0) > > > > > > A separate helper function dpu_unit_add_dbg() would work here too. > > > > Will create an array to contain all points of struct dpu_units and go > > through the array directly to show the debug message. The array can > > also be used by dpu_submodules_init() and dpu_submodules_hw_init(). > > > > The arrary will look like: > > static const struct dpu_units *dpu_all_units[] = { > > &dpu_cfs, > > &dpu_decs, > > &dpu_eds, > > &dpu_fds, > > &dpu_fes, > > &dpu_fgs, > > &dpu_fls, > > &dpu_fws, > > &dpu_gcs, > > &dpu_hss, > > &dpu_lbs, > > &dpu_tcons, > > &dpu_vss, > > }; > > > > > > + > > > > + DPU_UNITS_ADDR_DBG(cf); > > > > + DPU_UNITS_ADDR_DBG(dec); > > > > + DPU_UNITS_ADDR_DBG(ed); > > > > + DPU_UNITS_ADDR_DBG(fd); > > > > + DPU_UNITS_ADDR_DBG(fe); > > > > + DPU_UNITS_ADDR_DBG(fg); > > > > + DPU_UNITS_ADDR_DBG(fl); > > > > + DPU_UNITS_ADDR_DBG(fw); > > > > + DPU_UNITS_ADDR_DBG(gc); > > > > + DPU_UNITS_ADDR_DBG(hs); > > > > + DPU_UNITS_ADDR_DBG(lb); > > > > + DPU_UNITS_ADDR_DBG(tcon); > > > > + DPU_UNITS_ADDR_DBG(vs); > > > > > > And these could be changed into calling the helper directly. > > > > > > > +} > > > > + > > > > +static int dpu_get_irq(struct platform_device *pdev, struct dpu_soc *dpu) > > > > > > This could be renamed dpu_get_irqs(). > > > > Will do. > > > > > > +{ > > > > +#define DPU_GET_IRQ(name) \ > > > > +do { \ > > > > + dpu->irq_##name = platform_get_irq_byname(pdev, "" #name ""); \ > > > > + dev_dbg(dpu->dev, "get irq_" #name ": %d\n", dpu->irq_##name); \ > > > > + if (dpu->irq_##name < 0) { \ > > > > + dev_err_probe(dpu->dev, dpu->irq_##name, \ > > > > + "failed to get irq " #name "\n"); \ > > > > + return dpu->irq_##name; \ > > > > + } \ > > > > +} while (0) > > > > > > And this macro could be put under a new dpu_get_irq(): > > > > > > static int dpu_get_irq(struct platform_device *pdev, struct dpu_soc *dpu, > > > int *irq, const char *name) > > > > > > > + > > > > + DPU_GET_IRQ(disengcfg_framecomplete0); > > > > + DPU_GET_IRQ(disengcfg_seqcomplete0); > > > > + DPU_GET_IRQ(disengcfg_shdload0); > > > > + DPU_GET_IRQ(disengcfg_framecomplete1); > > > > + DPU_GET_IRQ(disengcfg_seqcomplete1); > > > > + DPU_GET_IRQ(disengcfg_shdload1); > > > > + DPU_GET_IRQ(extdst0_shdload); > > > > + DPU_GET_IRQ(extdst1_shdload); > > > > + DPU_GET_IRQ(extdst4_shdload); > > > > + DPU_GET_IRQ(extdst5_shdload); > > > > > > All these macros could be transformed into something like: > > > > > > ~~~ > > > struct { > > > int *irq; > > > const char *name; > > > } irqs[] = { > > > {&dpu->irq_disengcfg_framecomplete0, "disengcfg_framecomplete0"}, > > > {&dpu->irq_disengcfg_seqcomplete0, "disengcfg_seqcomplete0"}, > > > ... > > > }; > > > > > > for (i = 0; i < ARRAY_SIZE(irqs); i++) { > > > ret = dpu_get_irq(pdev, dpu, irqs[i].irq, irqs[i].name); > > > if (ret) > > > return ret; > > > } > > > ~~~ > > > > Instead of defining irqs individually, I'll use an array to store all > > irqs in struct dpu_soc. Then get all irqs by > > calling platform_get_irq() and store them in dpu->irq[]. > > > > > > + > > > > + return 0; > > > > +} > > > > + > > > > +static void dpu_irq_handle(struct irq_desc *desc, enum dpu_irq irq) > > > > +{ > > > > + struct dpu_soc *dpu = irq_desc_get_handler_data(desc); > > > > + struct irq_chip *chip = irq_desc_get_chip(desc); > > > > + unsigned int virq; > > > > + u32 status; > > > > + > > > > + chained_irq_enter(chip, desc); > > > > + > > > > + status = dpu_comctrl_read(dpu, USERINTERRUPTSTATUS(irq / 32)); > > > > + status &= dpu_comctrl_read(dpu, USERINTERRUPTENABLE(irq / 32)); > > > > + > > > > + if (status & BIT(irq % 32)) { > > > > + virq = irq_linear_revmap(dpu->domain, irq); > > > > + if (virq) > > > > + generic_handle_irq(virq); > > > > + } > > > > + > > > > + chained_irq_exit(chip, desc); > > > > +} > > > > + > > > > +#define DPU_IRQ_DISENGCFG_FRAMECOMPLETE_HANDLER_DEFINE(id) \ > > > > +static void \ > > > > +dpu_disengcfg_framecomplete##id##_irq_handler(struct irq_desc *desc) \ > > > > +{ \ > > > > + dpu_irq_handle(desc, DPU_IRQ_DISENGCFG_FRAMECOMPLETE##id); \ > > > > +} > > > > + > > > > +#define DPU_IRQ_DISENGCFG_SEQCOMPLETE_HANDLER_DEFINE(id) \ > > > > +static void \ > > > > +dpu_disengcfg_seqcomplete##id##_irq_handler(struct irq_desc *desc) \ > > > > +{ \ > > > > + dpu_irq_handle(desc, DPU_IRQ_DISENGCFG_SEQCOMPLETE##id); \ > > > > +} > > > > + > > > > +#define DPU_IRQ_DISENGCFG_SHDLOAD_HANDLER_DEFINE(id) \ > > > > +static void \ > > > > +dpu_disengcfg_shdload##id##_irq_handler(struct irq_desc *desc) \ > > > > +{ \ > > > > + dpu_irq_handle(desc, DPU_IRQ_DISENGCFG_SHDLOAD##id); \ > > > > +} > > > > + > > > > +#define DPU_IRQ_EXTDST_SHDLOAD_HANDLER_DEFINE(id) \ > > > > +static void \ > > > > +dpu_extdst##id##_shdload_irq_handler(struct irq_desc *desc) \ > > > > +{ \ > > > > + dpu_irq_handle(desc, DPU_IRQ_EXTDST##id##_SHDLOAD); \ > > > > +} > > > > I'll define the irq handlers directly and drop the macros. > > > > > > + > > > > +DPU_IRQ_DISENGCFG_FRAMECOMPLETE_HANDLER_DEFINE(0) > > > > +DPU_IRQ_DISENGCFG_FRAMECOMPLETE_HANDLER_DEFINE(1) > > > > + > > > > +DPU_IRQ_DISENGCFG_SEQCOMPLETE_HANDLER_DEFINE(0) > > > > +DPU_IRQ_DISENGCFG_SEQCOMPLETE_HANDLER_DEFINE(1) > > > > + > > > > +DPU_IRQ_DISENGCFG_SHDLOAD_HANDLER_DEFINE(0) > > > > +DPU_IRQ_DISENGCFG_SHDLOAD_HANDLER_DEFINE(1) > > > > + > > > > +DPU_IRQ_EXTDST_SHDLOAD_HANDLER_DEFINE(0) > > > > +DPU_IRQ_EXTDST_SHDLOAD_HANDLER_DEFINE(1) > > > > +DPU_IRQ_EXTDST_SHDLOAD_HANDLER_DEFINE(4) > > > > +DPU_IRQ_EXTDST_SHDLOAD_HANDLER_DEFINE(5) > > > > + > > > > +int dpu_map_irq(struct dpu_soc *dpu, int irq) > > > > +{ > > > > + int virq = irq_linear_revmap(dpu->domain, irq); > > > > + > > > > + if (!virq) > > > > + virq = irq_create_mapping(dpu->domain, irq); > > > > + > > > > + return virq; > > > > +} > > > > + > > > > +static const unsigned long unused_irq[2] = {0x00000000, 0xfffe0008}; > > > > + > > > > +static void dpu_irq_hw_init(struct dpu_soc *dpu) > > > > +{ > > > > + int i; > > > > + > > > > + for (i = 0; i < DPU_IRQ_COUNT; i += 32) { > > > > + /* mask and clear all interrupts */ > > > > + dpu_comctrl_write(dpu, USERINTERRUPTENABLE(i / 32), 0); > > > > + dpu_comctrl_write(dpu, USERINTERRUPTCLEAR(i / 32), > > > > + ~unused_irq[i / 32]); > > > > + dpu_comctrl_write(dpu, INTERRUPTENABLE(i / 32), 0); > > > > + dpu_comctrl_write(dpu, INTERRUPTCLEAR(i / 32), > > > > + ~unused_irq[i / 32]); > > > > + > > > > + /* set all interrupts to user mode */ > > > > + dpu_comctrl_write(dpu, USERINTERRUPTMASK(i / 32), > > > > + ~unused_irq[i / 32]); > > > > + } > > > > +} > > > > + > > > > +static int dpu_irq_init(struct dpu_soc *dpu) > > > > +{ > > > > + struct device *dev = dpu->dev; > > > > + struct irq_chip_generic *gc; > > > > + struct irq_chip_type *ct; > > > > + int ret, i; > > > > + > > > > + dpu->domain = irq_domain_add_linear(dev->of_node, DPU_IRQ_COUNT, > > > > + &irq_generic_chip_ops, dpu); > > > > + if (!dpu->domain) { > > > > + dev_err(dev, "failed to add irq domain\n"); > > > > + return -ENODEV; > > > > + } > > > > + > > > > + ret = irq_alloc_domain_generic_chips(dpu->domain, 32, 1, "DPU", > > > > + handle_level_irq, 0, 0, 0); > > > > + if (ret) { > > > > + dev_err(dev, "failed to alloc generic irq chips: %d\n", ret); > > > > + irq_domain_remove(dpu->domain); > > > > + return ret; > > > > + } > > > > + > > > > + for (i = 0; i < DPU_IRQ_COUNT; i += 32) { > > > > + gc = irq_get_domain_generic_chip(dpu->domain, i); > > > > + gc->reg_base = dpu->comctrl_reg; > > > > + gc->unused = unused_irq[i / 32]; > > > > + ct = gc->chip_types; > > > > + ct->chip.irq_ack = irq_gc_ack_set_bit; > > > > + ct->chip.irq_mask = irq_gc_mask_clr_bit; > > > > + ct->chip.irq_unmask = irq_gc_mask_set_bit; > > > > + ct->regs.ack = USERINTERRUPTCLEAR(i / 32); > > > > + ct->regs.mask = USERINTERRUPTENABLE(i / 32); > > > > + } > > > > + > > > > +#define DPU_IRQ_SET_CHAINED_HANDLER_AND_DATA1(name) \ > > > > +irq_set_chained_handler_and_data(dpu->irq_##name, dpu_##name##_irq_handler, dpu) > > > > Will create an array to store all irq handlers and go through it to do > > this. So, will drop this macro. > > > > > > + > > > > + DPU_IRQ_SET_CHAINED_HANDLER_AND_DATA1(disengcfg_framecomplete0); > > > > + DPU_IRQ_SET_CHAINED_HANDLER_AND_DATA1(disengcfg_seqcomplete0); > > > > + DPU_IRQ_SET_CHAINED_HANDLER_AND_DATA1(disengcfg_shdload0); > > > > + DPU_IRQ_SET_CHAINED_HANDLER_AND_DATA1(disengcfg_framecomplete1); > > > > + DPU_IRQ_SET_CHAINED_HANDLER_AND_DATA1(disengcfg_seqcomplete1); > > > > + DPU_IRQ_SET_CHAINED_HANDLER_AND_DATA1(disengcfg_shdload1); > > > > + DPU_IRQ_SET_CHAINED_HANDLER_AND_DATA1(extdst0_shdload); > > > > + DPU_IRQ_SET_CHAINED_HANDLER_AND_DATA1(extdst1_shdload); > > > > + DPU_IRQ_SET_CHAINED_HANDLER_AND_DATA1(extdst4_shdload); > > > > + DPU_IRQ_SET_CHAINED_HANDLER_AND_DATA1(extdst5_shdload); > > > > + > > > > + return ret; > > > > +} > > > > + > > > > +static void dpu_irq_exit(struct dpu_soc *dpu) > > > > +{ > > > > + unsigned int i, irq; > > > > + > > > > +#define DPU_IRQ_SET_CHAINED_HANDLER_AND_DATA2(name) \ > > > > +irq_set_chained_handler_and_data(dpu->irq_##name, NULL, NULL) > > > > Also will drop this macro. > > > > > > + > > > > + DPU_IRQ_SET_CHAINED_HANDLER_AND_DATA2(disengcfg_framecomplete0); > > > > + DPU_IRQ_SET_CHAINED_HANDLER_AND_DATA2(disengcfg_seqcomplete0); > > > > + DPU_IRQ_SET_CHAINED_HANDLER_AND_DATA2(disengcfg_shdload0); > > > > + DPU_IRQ_SET_CHAINED_HANDLER_AND_DATA2(disengcfg_framecomplete1); > > > > + DPU_IRQ_SET_CHAINED_HANDLER_AND_DATA2(disengcfg_seqcomplete1); > > > > + DPU_IRQ_SET_CHAINED_HANDLER_AND_DATA2(disengcfg_shdload1); > > > > + DPU_IRQ_SET_CHAINED_HANDLER_AND_DATA2(extdst0_shdload); > > > > + DPU_IRQ_SET_CHAINED_HANDLER_AND_DATA2(extdst1_shdload); > > > > + DPU_IRQ_SET_CHAINED_HANDLER_AND_DATA2(extdst4_shdload); > > > > + DPU_IRQ_SET_CHAINED_HANDLER_AND_DATA2(extdst5_shdload); > > > > + > > > > + for (i = 0; i < DPU_IRQ_COUNT; i++) { > > > > + irq = irq_linear_revmap(dpu->domain, i); > > > > + if (irq) > > > > + irq_dispose_mapping(irq); > > > > + } > > > > + > > > > + irq_domain_remove(dpu->domain); > > > > +} > > > > + > > > > +static void dpu_submodules_hw_init(struct dpu_soc *dpu) > > > > +{ > > > > +#define DPU_UNITS_HW_INIT(unit) \ > > > > +do { \ > > > > + const struct dpu_units *us = &dpu_##unit##s; \ > > > > + int i; \ > > > > + \ > > > > + for (i = 0; i < us->cnt; i++) \ > > > > + dpu_##unit##_hw_init(dpu, i); \ > > > > +} while (0) > > > > + > > > > + DPU_UNITS_HW_INIT(cf); > > > > + DPU_UNITS_HW_INIT(dec); > > > > + DPU_UNITS_HW_INIT(ed); > > > > + DPU_UNITS_HW_INIT(fd); > > > > + DPU_UNITS_HW_INIT(fe); > > > > + DPU_UNITS_HW_INIT(fg); > > > > + DPU_UNITS_HW_INIT(fl); > > > > + DPU_UNITS_HW_INIT(fw); > > > > + DPU_UNITS_HW_INIT(gc); > > > > + DPU_UNITS_HW_INIT(hs); > > > > + DPU_UNITS_HW_INIT(lb); > > > > + DPU_UNITS_HW_INIT(tcon); > > > > + DPU_UNITS_HW_INIT(vs); > > > > +} > > > > > > This entire function can be rewritten without macros and it wouldn't > > > take too much extra code... > > > > > > ~~~ > > > int i, j; > > > struct { > > > int cnt; > > > void (*hw_init)(struct dpu_soc *dpu, unsigned int index); > > > } hw_units[] = { > > > {dpu_cfs.cnt, dpu_cf_hw_init}, > > > {dpu_decs.cnt, dpu_dec_hw_init}, > > > ... > > > }; > > > > > > for (i = 0; i < ARRAY_SIZE(hw_units); i++) > > > for (j = 0; j < hw_units[i].cnt; j++) > > > hw_units[i].hw_init(dpu, i); > > > > > > ~~~ > > > > Will add a hw_init() callback in struct dpu_units and go through > > dpu_all_units[] to this. > > > > > > > > > + > > > > +static int dpu_submodules_init(struct dpu_soc *dpu, unsigned long dpu_base) > > > > +{ > > > > + int ret, i; > > > > + > > > > +#define DPU_UNIT_INIT(unit, base, index, id, type, pec_ofs, ofs) \ > > > > +do { \ > > > > + ret = dpu_##unit##_init(dpu, (index), (id), (type), \ > > > > + (pec_ofs) ? (base) + (pec_ofs) : 0, \ > > > > + (base) + (ofs)); \ > > > > + if (ret) { \ > > > > + dev_err(dpu->dev, "failed to initialize %s%d: %d\n", \ > > > > + #unit, (id), ret); \ > > > > + return ret; \ > > > > + } \ > > > > +} while (0) > > > > + > > > > +#define DPU_UNITS_INIT(unit) \ > > > > +do { \ > > > > + const struct dpu_units *us = &dpu_##unit##s; \ > > > > + \ > > > > + for (i = 0; i < us->cnt; i++) \ > > > > + DPU_UNIT_INIT(unit, dpu_base, i, \ > > > > + us->ids[i], us->types[i], \ > > > > + us->pec_ofss ? us->pec_ofss[i] : 0, \ > > > > + us->ofss[i]); \ > > > > +} while (0) > > > > + > > > > + DPU_UNITS_INIT(cf); > > > > + DPU_UNITS_INIT(dec); > > > > + DPU_UNITS_INIT(ed); > > > > + DPU_UNITS_INIT(fd); > > > > + DPU_UNITS_INIT(fe); > > > > + DPU_UNITS_INIT(fg); > > > > + DPU_UNITS_INIT(fl); > > > > + DPU_UNITS_INIT(fw); > > > > + DPU_UNITS_INIT(gc); > > > > + DPU_UNITS_INIT(hs); > > > > + DPU_UNITS_INIT(lb); > > > > + DPU_UNITS_INIT(tcon); > > > > + DPU_UNITS_INIT(vs); > > > > + > > > > + return 0; > > > > +} > > > > > > This one too. Macros can be avoided. > > > > Will add a init() callback in struct dpu_units and go through > > dpu_all_units[] to this. > > > > > > + > > > > +static int platform_remove_devices_fn(struct device *dev, void *unused) > > > > +{ > > > > + struct platform_device *pdev = to_platform_device(dev); > > > > + > > > > + platform_device_unregister(pdev); > > > > + > > > > + return 0; > > > > +} > > > > + > > > > +static void platform_device_unregister_children(struct platform_device *pdev) > > > > +{ > > > > + device_for_each_child(&pdev->dev, NULL, platform_remove_devices_fn); > > > > +} > > > > + > > > > +struct dpu_platform_reg { > > > > + struct dpu_client_platformdata pdata; > > > > + const char *name; > > > > +}; > > > > + > > > > +static struct dpu_platform_reg client_reg[] = { > > > > + { > > > > + .pdata = { > > > > + .stream_id = 0, > > > > + .dec_frame_complete_irq = DPU_IRQ_DISENGCFG_FRAMECOMPLETE0, > > > > + .dec_seq_complete_irq = DPU_IRQ_DISENGCFG_SEQCOMPLETE0, > > > > + .dec_shdld_irq = DPU_IRQ_DISENGCFG_SHDLOAD0, > > > > + .ed_cont_shdld_irq = DPU_IRQ_EXTDST0_SHDLOAD, > > > > + .ed_safe_shdld_irq = DPU_IRQ_EXTDST4_SHDLOAD, > > > > + }, > > > > + .name = "imx-dpu-crtc", > > > > + }, { > > > > + .pdata = { > > > > + .stream_id = 1, > > > > + .dec_frame_complete_irq = DPU_IRQ_DISENGCFG_FRAMECOMPLETE1, > > > > + .dec_seq_complete_irq = DPU_IRQ_DISENGCFG_SEQCOMPLETE1, > > > > + .dec_shdld_irq = DPU_IRQ_DISENGCFG_SHDLOAD1, > > > > + .ed_cont_shdld_irq = DPU_IRQ_EXTDST1_SHDLOAD, > > > > + .ed_safe_shdld_irq = DPU_IRQ_EXTDST5_SHDLOAD, > > > > + }, > > > > + .name = "imx-dpu-crtc", > > > > + } > > > > +}; > > > > + > > > > +static DEFINE_MUTEX(dpu_client_id_mutex); > > > > +static int dpu_client_id; > > > > + > > > > +static int dpu_get_plane_grp_res(struct dpu_soc *dpu, > > > > + struct dpu_plane_grp *grp) > > > > +{ > > > > + struct dpu_plane_res *res = &grp->res; > > > > + int i, j; > > > > + int ret = 0; > > > > + > > > > + INIT_LIST_HEAD(&grp->fu_list); > > > > + > > > > +#define DPU_UNITS_GET_FOR_PLANE_GRP(unit) \ > > > > +do { \ > > > > + for (i = 0; i < ARRAY_SIZE(unit##_ids); i++) { \ > > > > + if (unit##_types[i] == DPU_DISP) \ > > > > + res->unit##_cnt++; \ > > > > + } \ > > > > + \ > > > > + res->unit = devm_kcalloc(dpu->dev, res->unit##_cnt, \ > > > > + sizeof(*res->unit), GFP_KERNEL); \ > > > > + if (!res->unit) \ > > > > + return -ENOMEM; \ > > > > + \ > > > > + for (i = 0, j = 0; i < ARRAY_SIZE(unit##_ids); i++) { \ > > > > + if (unit##_types[i] != DPU_DISP) \ > > > > + continue; \ > > > > + \ > > > > + res->unit[j] = dpu_##unit##_get(dpu, unit##_ids[i]); \ > > > > + if (IS_ERR(res->unit[j])) { \ > > > > + ret = PTR_ERR(res->unit[j]); \ > > > > + dev_err(dpu->dev, \ > > > > + "failed to get %s%d: %d\n", \ > > > > + #unit, unit##_ids[i], ret); \ > > > > + return ret; \ > > > > + } \ > > > > + j++; \ > > > > + } \ > > > > +} while (0) > > > > > > This can be made a separate function too. > > > > Yes for the fetch units. > > > > Will get the layerblend alone as no good way to tell sizeof(*res- > > > unit). > > > > + > > > > + DPU_UNITS_GET_FOR_PLANE_GRP(fd); > > > > + DPU_UNITS_GET_FOR_PLANE_GRP(fl); > > > > + DPU_UNITS_GET_FOR_PLANE_GRP(fw); > > > > + DPU_UNITS_GET_FOR_PLANE_GRP(lb); > > > > + > > > > +#define DPU_FETCHUNIT_ADD_TO_PLANE_GRP_LIST(unit) \ > > > > +do { \ > > > > + for (i = res->unit##_cnt - 1; i >= 0; i--) \ > > > > + dpu_fu_add_to_list(res->unit[i], &grp->fu_list); \ > > > > +} while (0) > > > > Will drop this marco. > > > > > > + > > > > + DPU_FETCHUNIT_ADD_TO_PLANE_GRP_LIST(fd); > > > > + DPU_FETCHUNIT_ADD_TO_PLANE_GRP_LIST(fw); > > > > + DPU_FETCHUNIT_ADD_TO_PLANE_GRP_LIST(fl); > > > > + > > > > + grp->hw_plane_cnt = res->fd_cnt + res->fl_cnt + res->fw_cnt; > > > > + > > > > + return ret; > > > > +} > > > > + > > > > +static void dpu_put_plane_grp_res(struct dpu_plane_grp *grp) > > > > +{ > > > > + struct dpu_plane_res *res = &grp->res; > > > > + struct list_head *l, *tmp; > > > > + int i; > > > > + > > > > + grp->hw_plane_cnt = 0; > > > > + > > > > + list_for_each_safe(l, tmp, &grp->fu_list) > > > > + list_del(l); > > > > + > > > > +#define DPU_UNITS_PUT_FOR_PLANE_GRP(unit) \ > > > > +do { \ > > > > + for (i = 0; i < res->unit##_cnt; i++) { \ > > > > + if (!IS_ERR_OR_NULL(res->unit[i])) \ > > > > + dpu_##unit##_put(res->unit[i]); \ > > > > + } \ > > > > + res->unit##_cnt = 0; \ > > > > +} while (0) > > > > Will drop this macro. > > > > > > + > > > > + DPU_UNITS_PUT_FOR_PLANE_GRP(fd); > > > > + DPU_UNITS_PUT_FOR_PLANE_GRP(fl); > > > > + DPU_UNITS_PUT_FOR_PLANE_GRP(fw); > > > > + DPU_UNITS_PUT_FOR_PLANE_GRP(lb); > > > > +} > > > > + > > > > +static int dpu_add_client_devices(struct dpu_soc *dpu) > > > > +{ > > > > + struct device *dev = dpu->dev; > > > > + struct dpu_platform_reg *reg; > > > > + struct dpu_crtc_grp *crtc_grp; > > > > + struct dpu_plane_grp *plane_grp; > > > > + size_t client_cnt, reg_size; > > > > + int i, id, ret; > > > > + > > > > + client_cnt = ARRAY_SIZE(client_reg); > > > > + > > > > + reg = devm_kcalloc(dev, client_cnt, sizeof(*reg), GFP_KERNEL); > > > > + if (!reg) > > > > + return -ENOMEM; > > > > + > > > > + crtc_grp = devm_kzalloc(dev, sizeof(*crtc_grp), GFP_KERNEL); > > > > + if (!crtc_grp) > > > > + return -ENOMEM; > > > > + > > > > + plane_grp = devm_kzalloc(dev, sizeof(*plane_grp), GFP_KERNEL); > > > > + if (!plane_grp) > > > > + return -ENOMEM; > > > > + > > > > + crtc_grp->plane_grp = plane_grp; > > > > + > > > > + mutex_lock(&dpu_client_id_mutex); > > > > + id = dpu_client_id; > > > > + dpu_client_id += client_cnt; > > > > + mutex_unlock(&dpu_client_id_mutex); > > > > + > > > > + reg_size = client_cnt * sizeof(struct dpu_platform_reg); > > > > + memcpy(reg, &client_reg[0], reg_size); > > > > + > > > > + ret = dpu_get_plane_grp_res(dpu, plane_grp); > > > > + if (ret) > > > > + goto err_get_plane_res; > > > > + > > > > + for (i = 0; i < client_cnt; i++) { > > > > + struct platform_device *pdev; > > > > + struct device_node *np; > > > > + > > > > + /* Associate subdevice with the corresponding port node. */ > > > > + np = of_graph_get_port_by_id(dev->of_node, i); > > > > + if (!np) { > > > > + dev_info(dev, > > > > + "no port@%d node in %s, not using DISP%d\n", > > > > + i, dev->of_node->full_name, i); > > > > + continue; > > > > + } > > > > + > > > > + reg[i].pdata.crtc_grp = crtc_grp; > > > > + > > > > + pdev = platform_device_alloc(reg[i].name, id++); > > > > + if (!pdev) { > > > > + ret = -ENOMEM; > > > > + goto err_register; > > > > + } > > > > + > > > > + pdev->dev.parent = dev; > > > > + pdev->dev.of_node = np; > > > > + pdev->dev.coherent_dma_mask = DMA_BIT_MASK(32); > > > > + pdev->dev.dma_mask = &pdev->dev.coherent_dma_mask; > > > > + > > > > + reg[i].pdata.of_node = np; > > > > + ret = platform_device_add_data(pdev, ®[i].pdata, > > > > + sizeof(reg[i].pdata)); > > > > + if (!ret) > > > > + ret = platform_device_add(pdev); > > > > + if (ret) { > > > > + platform_device_put(pdev); > > > > + goto err_register; > > > > + } > > > > + } > > > > + > > > > + return ret; > > > > + > > > > +err_register: > > > > + platform_device_unregister_children(to_platform_device(dev)); > > > > +err_get_plane_res: > > > > + dpu_put_plane_grp_res(plane_grp); > > > > + > > > > + return ret; > > > > +} > > > > + > > > > +static int dpu_core_probe(struct platform_device *pdev) > > > > +{ > > > > + struct device *dev = &pdev->dev; > > > > + struct device_node *np = dev->of_node; > > > > + struct dpu_soc *dpu; > > > > + struct resource *res; > > > > + unsigned long dpu_base; > > > > + int ret; > > > > + > > > > + res = platform_get_resource(pdev, IORESOURCE_MEM, 0); > > > > + if (!res) > > > > + return -ENODEV; > > > > + > > > > + dpu_base = res->start; > > > > + > > > > + dpu = devm_kzalloc(dev, sizeof(*dpu), GFP_KERNEL); > > > > + if (!dpu) > > > > + return -ENOMEM; > > > > + > > > > + dpu->dev = dev; > > > > + > > > > + dpu->id = of_alias_get_id(np, "dpu"); > > > > + if (dpu->id < 0) { > > > > + dev_err(dev, "failed to get dpu node alias id: %d\n", dpu->id); > > > > + return dpu->id; > > > > + } > > > > + > > > > + dpu_units_addr_dbg(dpu, dpu_base); > > > > + > > > > + ret = dpu_get_irq(pdev, dpu); > > > > + if (ret) > > > > + return ret; > > > > + > > > > + dpu->comctrl_reg = devm_ioremap(dev, dpu_base, SZ_512); > > > > + if (!dpu->comctrl_reg) > > > > + return -ENOMEM; > > > > + > > > > + ret = dpu_attach_pm_domains(dpu); > > > > + if (ret) > > > > + return ret; > > > > + > > > > + dpu->clk_cfg = devm_clk_get(dev, "cfg"); > > > > + if (IS_ERR(dpu->clk_cfg)) { > > > > + ret = PTR_ERR(dpu->clk_cfg); > > > > + dev_err_probe(dev, ret, "failed to get cfg clock\n"); > > > > + goto failed_clk_cfg_get; > > > > + } > > > > + > > > > + dpu->clk_axi = devm_clk_get(dev, "axi"); > > > > + if (IS_ERR(dpu->clk_axi)) { > > > > + ret = PTR_ERR(dpu->clk_axi); > > > > + dev_err_probe(dev, ret, "failed to get axi clock\n"); > > > > + goto failed_clk_axi_get; > > > > + } > > > > + > > > > + ret = dpu_irq_init(dpu); > > > > + if (ret) > > > > + goto failed_irq_init; > > > > + > > > > + ret = dpu_submodules_init(dpu, dpu_base); > > > > + if (ret) > > > > + goto failed_submodules_init; > > > > + > > > > + platform_set_drvdata(pdev, dpu); > > > > + > > > > + pm_runtime_enable(dev); > > > > + > > > > + ret = dpu_add_client_devices(dpu); > > > > + if (ret) { > > > > + dev_err(dev, "failed to add client devices: %d\n", ret); > > > > + goto failed_add_clients; > > > > + } > > > > + > > > > + return ret; > > > > + > > > > +failed_add_clients: > > > > + pm_runtime_disable(dev); > > > > +failed_submodules_init: > > > > + dpu_irq_exit(dpu); > > > > +failed_irq_init: > > > > +failed_clk_axi_get: > > > > +failed_clk_cfg_get: > > > > + dpu_detach_pm_domains(dpu); > > > > + return ret; > > > > +} > > > > + > > > > +static int dpu_core_remove(struct platform_device *pdev) > > > > +{ > > > > + struct dpu_soc *dpu = platform_get_drvdata(pdev); > > > > + > > > > + platform_device_unregister_children(pdev); > > > > + pm_runtime_disable(dpu->dev); > > > > + dpu_irq_exit(dpu); > > > > + dpu_detach_pm_domains(dpu); > > > > + > > > > + return 0; > > > > +} > > > > + > > > > +static int __maybe_unused dpu_runtime_suspend(struct device *dev) > > > > +{ > > > > + struct platform_device *pdev = to_platform_device(dev); > > > > + struct dpu_soc *dpu = platform_get_drvdata(pdev); > > > > + > > > > + clk_disable_unprepare(dpu->clk_axi); > > > > + clk_disable_unprepare(dpu->clk_cfg); > > > > + > > > > + dev_dbg(dev, "suspended\n"); > > > > + > > > > + return 0; > > > > +} > > > > + > > > > +static int __maybe_unused dpu_runtime_resume(struct device *dev) > > > > +{ > > > > + struct platform_device *pdev = to_platform_device(dev); > > > > + struct dpu_soc *dpu = platform_get_drvdata(pdev); > > > > + int ret; > > > > + > > > > + ret = clk_prepare_enable(dpu->clk_cfg); > > > > + if (ret) { > > > > + dev_err(dev, "failed to enable cfg clock: %d\n", ret); > > > > + return ret; > > > > + } > > > > + ret = clk_prepare_enable(dpu->clk_axi); > > > > + if (ret) { > > > > + clk_disable_unprepare(dpu->clk_cfg); > > > > + dev_err(dev, "failed to enable axi clock: %d\n", ret); > > > > + return ret; > > > > + } > > > > + > > > > + dpu_irq_hw_init(dpu); > > > > + > > > > + dpu_submodules_hw_init(dpu); > > > > + > > > > + dev_dbg(dev, "resumed\n"); > > > > + > > > > + return ret; > > > > +} > > > > + > > > > +static const struct dev_pm_ops dpu_pm_ops = { > > > > + SET_LATE_SYSTEM_SLEEP_PM_OPS(pm_runtime_force_suspend, > > > > + pm_runtime_force_resume) > > > > + SET_RUNTIME_PM_OPS(dpu_runtime_suspend, dpu_runtime_resume, NULL) > > > > +}; > > > > + > > > > +const struct of_device_id dpu_dt_ids[] = { > > > > + { .compatible = "fsl,imx8qm-dpu" }, > > > > + { .compatible = "fsl,imx8qxp-dpu" }, > > > > + { /* sentinel */ } > > > > +}; > > > > +MODULE_DEVICE_TABLE(of, dpu_dt_ids); > > > > + > > > > +struct platform_driver dpu_core_driver = { > > > > + .driver = { > > > > + .pm = &dpu_pm_ops, > > > > + .name = "dpu-core", > > > > + .of_match_table = dpu_dt_ids, > > > > + }, > > > > + .probe = dpu_core_probe, > > > > + .remove = dpu_core_remove, > > > > +}; > > > > diff --git a/drivers/gpu/drm/imx/dpu/dpu-crtc.c b/drivers/gpu/drm/imx/dpu/dpu-crtc.c > > > > new file mode 100644 > > > > index 00000000..c21bd1d > > > > --- /dev/null > > > > +++ b/drivers/gpu/drm/imx/dpu/dpu-crtc.c > > > > @@ -0,0 +1,925 @@ > > > > +// SPDX-License-Identifier: GPL-2.0+ > > > > + > > > > +/* > > > > + * Copyright 2017-2020 NXP > > > > + */ > > > > + > > > > +#include <linux/component.h> > > > > +#include <linux/irq.h> > > > > +#include <linux/irqflags.h> > > > > +#include <linux/pm_runtime.h> > > > > +#include <linux/preempt.h> > > > > +#include <linux/spinlock.h> > > > > + > > > > +#include <drm/drm_atomic.h> > > > > +#include <drm/drm_atomic_helper.h> > > > > +#include <drm/drm_atomic_state_helper.h> > > > > +#include <drm/drm_color_mgmt.h> > > > > + > > > > +#include "dpu.h" > > > > +#include "dpu-crtc.h" > > > > +#include "dpu-dprc.h" > > > > +#include "dpu-drv.h" > > > > +#include "dpu-plane.h" > > > > + > > > > +#define DPU_CRTC_WAIT_FOR_COMPLETION_TIMEOUT(_name) \ > > > > +do { \ > > > > + unsigned long ret; \ > > > > + ret = wait_for_completion_timeout(&dpu_crtc->_name, HZ); \ > > > > + if (ret == 0) \ > > > > + drm_err(crtc->dev, "[CRTC:%d:%s] %s: wait for " #_name \ > > > > + " timeout\n", \ > > > > + crtc->base.id, crtc->name, __func__); \ > > > > +} while (0) > > > > + > > > > +#define DPU_CRTC_WAIT_FOR_FRAMEGEN_FRAME_CNT_MOVING(fg) \ > > > > +do { \ > > > > + if (dpu_fg_wait_for_frame_counter_moving(fg)) \ > > > > + drm_err(crtc->dev, "[CRTC:%d:%s] %s: " \ > > > > + "FrameGen frame counter isn't moving\n", \ > > > > + crtc->base.id, crtc->name, __func__); \ > > > > +} while (0) > > > > + > > > > +#define DPU_CRTC_CHECK_FRAMEGEN_FIFO(fg) \ > > > > +do { \ > > > > + if (dpu_fg_secondary_requests_to_read_empty_fifo(fg)) { \ > > > > + dpu_fg_secondary_clear_channel_status(fg); \ > > > > + drm_err(crtc->dev, \ > > > > + "[CRTC:%d:%s] %s: FrameGen FIFO empty\n", \ > > > > + crtc->base.id, crtc->name, __func__); \ > > > > + } \ > > > > +} while (0) > > > > + > > > > +#define DPU_CRTC_WAIT_FOR_FRAMEGEN_SECONDARY_SYNCUP(fg) \ > > > > +do { \ > > > > + if (dpu_fg_wait_for_secondary_syncup(fg)) \ > > > > + drm_err(crtc->dev, \ > > > > + "[CRTC:%d:%s] %s: " \ > > > > + "FrameGen secondary channel isn't syncup\n", \ > > > > + crtc->base.id, crtc->name, __func__); \ > > > > +} while (0) > > > > + > > > > +static u32 dpu_crtc_get_vblank_counter(struct drm_crtc *crtc) > > > > +{ > > > > + struct dpu_crtc *dpu_crtc = to_dpu_crtc(crtc); > > > > + > > > > + if (pm_runtime_active(dpu_crtc->dev->parent)) > > > > + return dpu_fg_get_frame_index(dpu_crtc->fg); > > > > + else > > > > + return (u32)drm_crtc_vblank_count(crtc); > > > > +} > > > > + > > > > +static int dpu_crtc_enable_vblank(struct drm_crtc *crtc) > > > > +{ > > > > + struct dpu_crtc *dpu_crtc = to_dpu_crtc(crtc); > > > > + > > > > + enable_irq(dpu_crtc->dec_frame_complete_irq); > > > > + > > > > + return 0; > > > > +} > > > > + > > > > +static void dpu_crtc_disable_vblank(struct drm_crtc *crtc) > > > > +{ > > > > + struct dpu_crtc *dpu_crtc = to_dpu_crtc(crtc); > > > > + > > > > + disable_irq_nosync(dpu_crtc->dec_frame_complete_irq); > > > > +} > > > > + > > > > +static irqreturn_t > > > > +dpu_crtc_dec_frame_complete_irq_handler(int irq, void *dev_id) > > > > +{ > > > > + struct dpu_crtc *dpu_crtc = dev_id; > > > > + struct drm_crtc *crtc = &dpu_crtc->base; > > > > + unsigned long flags; > > > > + > > > > + drm_crtc_handle_vblank(crtc); > > > > + > > > > + spin_lock_irqsave(&crtc->dev->event_lock, flags); > > > > + if (dpu_crtc->event) { > > > > + drm_crtc_send_vblank_event(crtc, dpu_crtc->event); > > > > + dpu_crtc->event = NULL; > > > > + drm_crtc_vblank_put(crtc); > > > > + } > > > > + spin_unlock_irqrestore(&crtc->dev->event_lock, flags); > > > > + > > > > + return IRQ_HANDLED; > > > > +} > > > > + > > > > +#define DPU_CRTC_IRQ_HANDLER_DEFINE(name) \ > > > > +static irqreturn_t dpu_crtc_##name##_irq_handler(int irq, void *dev_id) \ > > > > +{ \ > > > > + struct dpu_crtc *dpu_crtc = dev_id; \ > > > > + complete(&dpu_crtc->name##_done); \ > > > > + return IRQ_HANDLED; \ > > > > +} > > > > Will drop this macro and define a common irq handler. > > > > > > + > > > > +DPU_CRTC_IRQ_HANDLER_DEFINE(dec_seq_complete) > > > > +DPU_CRTC_IRQ_HANDLER_DEFINE(dec_shdld) > > > > +DPU_CRTC_IRQ_HANDLER_DEFINE(ed_cont_shdld) > > > > +DPU_CRTC_IRQ_HANDLER_DEFINE(ed_safe_shdld) > > > > + > > > > +static const struct drm_crtc_funcs dpu_crtc_funcs = { > > > > + .reset = drm_atomic_helper_crtc_reset, > > > > + .destroy = drm_crtc_cleanup, > > > > + .set_config = drm_atomic_helper_set_config, > > > > + .page_flip = drm_atomic_helper_page_flip, > > > > + .atomic_duplicate_state = drm_atomic_helper_crtc_duplicate_state, > > > > + .atomic_destroy_state = drm_atomic_helper_crtc_destroy_state, > > > > + .get_vblank_counter = dpu_crtc_get_vblank_counter, > > > > + .enable_vblank = dpu_crtc_enable_vblank, > > > > + .disable_vblank = dpu_crtc_disable_vblank, > > > > + .get_vblank_timestamp = drm_crtc_vblank_helper_get_vblank_timestamp, > > > > +}; > > > > + > > > > +static void dpu_crtc_queue_state_event(struct drm_crtc *crtc) > > > > +{ > > > > + struct dpu_crtc *dpu_crtc = to_dpu_crtc(crtc); > > > > + > > > > + spin_lock_irq(&crtc->dev->event_lock); > > > > + if (crtc->state->event) { > > > > + WARN_ON(drm_crtc_vblank_get(crtc)); > > > > + WARN_ON(dpu_crtc->event); > > > > + dpu_crtc->event = crtc->state->event; > > > > + crtc->state->event = NULL; > > > > + } > > > > + spin_unlock_irq(&crtc->dev->event_lock); > > > > +} > > > > + > > > > +static enum drm_mode_status > > > > +dpu_crtc_mode_valid(struct drm_crtc *crtc, const struct drm_display_mode *mode) > > > > +{ > > > > + if (mode->crtc_clock > DPU_FRAMEGEN_MAX_CLOCK) > > > > + return MODE_CLOCK_HIGH; > > > > + > > > > + return MODE_OK; > > > > +} > > > > + > > > > +static void dpu_crtc_pm_runtime_get_sync(struct drm_crtc *crtc) > > > > +{ > > > > + struct dpu_crtc *dpu_crtc = to_dpu_crtc(crtc); > > > > + int ret; > > > > + > > > > + ret = pm_runtime_get_sync(dpu_crtc->dev->parent); > > > > + if (ret < 0) { > > > > + pm_runtime_put_noidle(dpu_crtc->dev->parent); > > > > + drm_err(crtc->dev, > > > > + "[CRTC:%d:%s]: failed to get parent device RPM sync\n", > > > > + crtc->base.id, crtc->name); > > > > + } > > > > +} > > > > + > > > > +static void dpu_crtc_pm_runtime_put(struct drm_crtc *crtc) > > > > +{ > > > > + struct dpu_crtc *dpu_crtc = to_dpu_crtc(crtc); > > > > + int ret; > > > > + > > > > + ret = pm_runtime_put(dpu_crtc->dev->parent); > > > > + if (ret < 0) { > > > > + drm_err(crtc->dev, > > > > + "[CRTC:%d:%s]: failed to put parent device RPM\n", > > > > + crtc->base.id, crtc->name); > > > > + } > > > > +} > > > > + > > > > +static void dpu_crtc_mode_set_nofb(struct drm_crtc *crtc) > > > > +{ > > > > + struct dpu_crtc *dpu_crtc = to_dpu_crtc(crtc); > > > > + struct drm_display_mode *adj = &crtc->state->adjusted_mode; > > > > + enum dpu_link_id cf_link; > > > > + > > > > + dpu_crtc_dbg(crtc, "mode " DRM_MODE_FMT "\n", DRM_MODE_ARG(adj)); > > > > + > > > > + /* request power-on when we start to set mode for CRTC */ > > > > + dpu_crtc_pm_runtime_get_sync(crtc); > > > > + > > > > + dpu_fg_displaymode(dpu_crtc->fg, FG_DM_SEC_ON_TOP); > > > > + dpu_fg_panic_displaymode(dpu_crtc->fg, FG_DM_CONSTCOL); > > > > + dpu_fg_cfg_videomode(dpu_crtc->fg, adj); > > > > + > > > > + dpu_tcon_cfg_videomode(dpu_crtc->tcon, adj); > > > > + dpu_tcon_set_fmt(dpu_crtc->tcon); > > > > + > > > > + dpu_cf_framedimensions(dpu_crtc->cf_cont, > > > > + adj->crtc_hdisplay, adj->crtc_vdisplay); > > > > + dpu_cf_framedimensions(dpu_crtc->cf_safe, > > > > + adj->crtc_hdisplay, adj->crtc_vdisplay); > > > > + /* constframe in content stream shows black frame - CRTC background */ > > > > + dpu_cf_constantcolor_black(dpu_crtc->cf_cont); > > > > + /* constframe in safety stream shows blue frame */ > > > > + dpu_cf_constantcolor_blue(dpu_crtc->cf_safe); > > > > + > > > > + cf_link = dpu_cf_get_link_id(dpu_crtc->cf_safe); > > > > + dpu_ed_pec_src_sel(dpu_crtc->ed_safe, cf_link); > > > > + > > > > + cf_link = dpu_cf_get_link_id(dpu_crtc->cf_cont); > > > > + dpu_ed_pec_src_sel(dpu_crtc->ed_cont, cf_link); > > > > +} > > > > + > > > > +static int dpu_crtc_atomic_check_gamma(struct drm_crtc *crtc, > > > > + struct drm_crtc_state *state) > > > > +{ > > > > + size_t lut_size; > > > > + > > > > + if (!state->color_mgmt_changed || !state->gamma_lut) > > > > + return 0; > > > > + > > > > + if (crtc->state->gamma_lut && > > > > + (crtc->state->gamma_lut->base.id == state->gamma_lut->base.id)) > > > > + return 0; > > > > + > > > > + if (state->gamma_lut->length % sizeof(struct drm_color_lut)) { > > > > + dpu_crtc_dbg(crtc, "wrong gamma_lut length\n"); > > > > + return -EINVAL; > > > > + } > > > > + > > > > + lut_size = state->gamma_lut->length / sizeof(struct drm_color_lut); > > > > + if (lut_size != 256) { > > > > + dpu_crtc_dbg(crtc, "gamma_lut size is not 256\n"); > > > > + return -EINVAL; > > > > + } > > > > + > > > > + return 0; > > > > +} > > > > + > > > > +static int dpu_crtc_atomic_check(struct drm_crtc *crtc, > > > > + struct drm_atomic_state *state) > > > > +{ > > > > + struct drm_crtc_state *crtc_state; > > > > + int ret; > > > > + > > > > + crtc_state = drm_atomic_get_new_crtc_state(state, crtc); > > > > + > > > > + ret = dpu_crtc_atomic_check_gamma(crtc, crtc_state); > > > > + if (ret) > > > > + return ret; > > > > + > > > > + /* force a mode set if the CRTC is changed to active */ > > > > + if (crtc_state->active_changed && crtc_state->active) { > > > > + /* > > > > + * If mode_changed is set by us, call > > > > + * drm_atomic_helper_check_modeset() as it's Kerneldoc requires. > > > > + */ > > > > + if (!crtc_state->mode_changed) { > > > > + crtc_state->mode_changed = true; > > > > + > > > > + ret = drm_atomic_helper_check_modeset(crtc->dev, state); > > > > + if (ret) > > > > + return ret; > > > > + } > > > > + } > > > > + > > > > + return ret; > > > > +} > > > > + > > > > +static void dpu_crtc_atomic_begin(struct drm_crtc *crtc, > > > > + struct drm_atomic_state *state) > > > > +{ > > > > + struct drm_crtc_state *old_crtc_state; > > > > + struct drm_atomic_state *old_state; > > > > + struct dpu_crtc *dpu_crtc = to_dpu_crtc(crtc); > > > > + struct drm_plane *plane; > > > > + struct drm_plane_state *old_plane_state; > > > > + struct dpu_plane_state *old_dpstate; > > > > + struct dpu_fetchunit *fu; > > > > + const struct dpu_fetchunit_ops *fu_ops; > > > > + enum dpu_link_id cf_link; > > > > + int i; > > > > + > > > > + old_crtc_state = drm_atomic_get_old_crtc_state(state, crtc); > > > > + old_state = old_crtc_state->state; > > > > + > > > > + /* do nothing if planes keep being disabled */ > > > > + if (old_crtc_state->plane_mask == 0 && crtc->state->plane_mask == 0) > > > > + return; > > > > + > > > > + /* request power-on when any plane starts to be active */ > > > > + if (old_crtc_state->plane_mask == 0 && crtc->state->plane_mask != 0) > > > > + dpu_crtc_pm_runtime_get_sync(crtc); > > > > + > > > > + /* > > > > + * Disable relevant planes' resources in SHADOW only. > > > > + * Whether any of them would be disabled or kept running depends > > > > + * on new plane states in the new global atomic state. > > > > + */ > > > > + for_each_old_plane_in_state(old_state, plane, old_plane_state, i) { > > > > + old_dpstate = to_dpu_plane_state(old_plane_state); > > > > + > > > > + if (!old_plane_state->fb) > > > > + continue; > > > > + > > > > + if (old_plane_state->crtc != crtc) > > > > + continue; > > > > + > > > > + fu = old_dpstate->source; > > > > + > > > > + fu_ops = dpu_fu_get_ops(fu); > > > > + > > > > + fu_ops->disable_src_buf(fu); > > > > + > > > > + if (old_dpstate->is_top) { > > > > + cf_link = dpu_cf_get_link_id(dpu_crtc->cf_cont); > > > > + dpu_ed_pec_src_sel(dpu_crtc->ed_cont, cf_link); > > > > + } > > > > + } > > > > +} > > > > + > > > > +static void dpu_crtc_set_gammacor(struct dpu_crtc *dpu_crtc) > > > > +{ > > > > + struct drm_crtc *crtc = &dpu_crtc->base; > > > > + struct drm_color_lut *lut; > > > > + > > > > + lut = (struct drm_color_lut *)crtc->state->gamma_lut->data; > > > > + > > > > + dpu_gc_enable_rgb_write(dpu_crtc->gc); > > > > + dpu_gc_mode(dpu_crtc->gc, GC_GAMMACOR); > > > > + > > > > + dpu_gc_start_rgb(dpu_crtc->gc, lut); > > > > + dpu_gc_delta_rgb(dpu_crtc->gc, lut); > > > > +} > > > > + > > > > +static void dpu_crtc_set_gammacor_sync(struct dpu_crtc *dpu_crtc) > > > > +{ > > > > + struct drm_crtc *crtc = &dpu_crtc->base; > > > > + > > > > + enable_irq(dpu_crtc->dec_shdld_irq); > > > > + > > > > + dpu_crtc_set_gammacor(dpu_crtc); > > > > + dpu_fg_shdtokgen(dpu_crtc->fg); > > > > + DPU_CRTC_WAIT_FOR_COMPLETION_TIMEOUT(dec_shdld_done); > > > > + > > > > + disable_irq(dpu_crtc->dec_shdld_irq); > > > > +} > > > > + > > > > +static void dpu_crtc_disable_gammacor(struct dpu_crtc *dpu_crtc) > > > > +{ > > > > + dpu_gc_mode(dpu_crtc->gc, GC_NEUTRAL); > > > > + dpu_gc_disable_rgb_write(dpu_crtc->gc); > > > > +} > > > > + > > > > +static void dpu_crtc_disable_gammacor_sync(struct dpu_crtc *dpu_crtc) > > > > +{ > > > > + struct drm_crtc *crtc = &dpu_crtc->base; > > > > + > > > > + enable_irq(dpu_crtc->dec_shdld_irq); > > > > + > > > > + dpu_crtc_disable_gammacor(dpu_crtc); > > > > + dpu_fg_shdtokgen(dpu_crtc->fg); > > > > + DPU_CRTC_WAIT_FOR_COMPLETION_TIMEOUT(dec_shdld_done); > > > > + > > > > + disable_irq(dpu_crtc->dec_shdld_irq); > > > > +} > > > > + > > > > +static void dpu_crtc_atomic_flush(struct drm_crtc *crtc, > > > > + struct drm_atomic_state *state) > > > > +{ > > > > + struct drm_crtc_state *old_crtc_state; > > > > + struct drm_atomic_state *old_state; > > > > + struct dpu_crtc *dpu_crtc = to_dpu_crtc(crtc); > > > > + struct drm_plane *plane; > > > > + struct drm_plane_state *old_plane_state; > > > > + struct dpu_plane_state *old_dpstate; > > > > + struct dpu_fetchunit *fu; > > > > + struct dpu_dprc *dprc; > > > > + const struct dpu_fetchunit_ops *fu_ops; > > > > + bool need_modeset = drm_atomic_crtc_needs_modeset(crtc->state); > > > > + unsigned long flags; > > > > + int i; > > > > + > > > > + old_crtc_state = drm_atomic_get_old_crtc_state(state, crtc); > > > > + old_state = old_crtc_state->state; > > > > + > > > > + if (old_crtc_state->plane_mask == 0 && crtc->state->plane_mask == 0) { > > > > + /* Queue a pending vbl event if necessary. */ > > > > + if (!need_modeset && crtc->state->active) > > > > + dpu_crtc_queue_state_event(crtc); > > > > + return; > > > > + } > > > > + > > > > + if (!need_modeset && crtc->state->active) > > > > + enable_irq(dpu_crtc->ed_cont_shdld_irq); > > > > + > > > > + /* > > > > + * Don't relinquish CPU until DPRC repeat_en is disabled > > > > + * and flush is done(if necessary). > > > > + */ > > > > + local_irq_save(flags); > > > > + preempt_disable(); > > > > + > > > > + /* > > > > + * Scan over old plane fetchunits to determine if we > > > > + * need to wait for FrameGen frame counter moving in > > > > + * the next loop prior to DPRC repeat_en disablement > > > > + * or not. > > > > + */ > > > > + for_each_old_plane_in_state(old_state, plane, old_plane_state, i) { > > > > + old_dpstate = to_dpu_plane_state(old_plane_state); > > > > + > > > > + if (!old_plane_state->fb) > > > > + continue; > > > > + > > > > + if (old_plane_state->crtc != crtc) > > > > + continue; > > > > + > > > > + fu = old_dpstate->source; > > > > + > > > > + fu_ops = dpu_fu_get_ops(fu); > > > > + > > > > + /* > > > > + * Sync with FrameGen frame counter moving so that > > > > + * we may disable DPRC repeat_en correctly. > > > > + */ > > > > + if (!fu_ops->is_enabled(fu) && !need_modeset && > > > > + old_crtc_state->active) { > > > > + DPU_CRTC_WAIT_FOR_FRAMEGEN_FRAME_CNT_MOVING(dpu_crtc->fg); > > > > + break; > > > > + } > > > > + } > > > > + > > > > + /* > > > > + * Set no stream id for disabled fetchunits of relevant planes. > > > > + * Also, disable DPRC repeat_en if necessary. > > > > + */ > > > > + for_each_old_plane_in_state(old_state, plane, old_plane_state, i) { > > > > + old_dpstate = to_dpu_plane_state(old_plane_state); > > > > + > > > > + if (!old_plane_state->fb) > > > > + continue; > > > > + > > > > + if (old_plane_state->crtc != crtc) > > > > + continue; > > > > + > > > > + fu = old_dpstate->source; > > > > + > > > > + fu_ops = dpu_fu_get_ops(fu); > > > > + > > > > + if (!fu_ops->is_enabled(fu)) { > > > > + fu_ops->set_no_stream_id(fu); > > > > + > > > > + dprc = fu_ops->get_dprc(fu); > > > > + dpu_dprc_disable_repeat_en(dprc); > > > > + } > > > > + } > > > > + > > > > + if (!need_modeset && crtc->state->active) { > > > > + /* > > > > + * Flush plane(s) update out to display & queue a pending > > > > + * vbl event if necessary. > > > > + */ > > > > + dpu_ed_pec_sync_trigger(dpu_crtc->ed_cont); > > > > + > > > > + local_irq_restore(flags); > > > > + preempt_enable(); > > > > + > > > > + if (old_crtc_state->gamma_lut && !crtc->state->gamma_lut) > > > > + dpu_crtc_disable_gammacor_sync(dpu_crtc); > > > > + else if (old_crtc_state->gamma_lut && crtc->state->gamma_lut && > > > > + old_crtc_state->gamma_lut->base.id != > > > > + crtc->state->gamma_lut->base.id) > > > > + dpu_crtc_set_gammacor_sync(dpu_crtc); > > > > + > > > > + DPU_CRTC_WAIT_FOR_COMPLETION_TIMEOUT(ed_cont_shdld_done); > > > > + > > > > + disable_irq(dpu_crtc->ed_cont_shdld_irq); > > > > + > > > > + DPU_CRTC_CHECK_FRAMEGEN_FIFO(dpu_crtc->fg); > > > > + > > > > + dpu_crtc_queue_state_event(crtc); > > > > + } else { > > > > + /* > > > > + * Simply flush and hope that any update takes effect > > > > + * if CRTC is disabled. This helps for the case where > > > > + * migrating plane(s) from a disabled CRTC to the other > > > > + * CRTC. > > > > + */ > > > > + if (!crtc->state->active) > > > > + dpu_ed_pec_sync_trigger(dpu_crtc->ed_cont); > > > > + > > > > + local_irq_restore(flags); > > > > + preempt_enable(); > > > > + } > > > > + > > > > + /* request power-off when all planes are off */ > > > > + if (old_crtc_state->plane_mask != 0 && crtc->state->plane_mask == 0) > > > > + dpu_crtc_pm_runtime_put(crtc); > > > > +} > > > > + > > > > +static void dpu_crtc_atomic_enable(struct drm_crtc *crtc, > > > > + struct drm_atomic_state *state) > > > > +{ > > > > + struct dpu_crtc *dpu_crtc = to_dpu_crtc(crtc); > > > > + unsigned long flags; > > > > + > > > > + drm_crtc_vblank_on(crtc); > > > > + > > > > + enable_irq(dpu_crtc->dec_shdld_irq); > > > > + enable_irq(dpu_crtc->ed_cont_shdld_irq); > > > > + enable_irq(dpu_crtc->ed_safe_shdld_irq); > > > > + > > > > + dpu_fg_enable_clock(dpu_crtc->fg); > > > > + dpu_ed_pec_sync_trigger(dpu_crtc->ed_cont); > > > > + dpu_ed_pec_sync_trigger(dpu_crtc->ed_safe); > > > > + if (crtc->state->gamma_lut) > > > > + dpu_crtc_set_gammacor(dpu_crtc); > > > > + else > > > > + dpu_crtc_disable_gammacor(dpu_crtc); > > > > + dpu_fg_shdtokgen(dpu_crtc->fg); > > > > + > > > > + /* don't relinquish CPU until TCON is set to operation mode */ > > > > + local_irq_save(flags); > > > > + preempt_disable(); > > > > + dpu_fg_enable(dpu_crtc->fg); > > > > + > > > > + /* > > > > + * TKT320590: > > > > + * Turn TCON into operation mode as soon as the first dumb > > > > + * frame is generated by DPU(we don't relinquish CPU to ensure > > > > + * this). This makes DPR/PRG be able to evade the frame. > > > > + */ > > > > + DPU_CRTC_WAIT_FOR_FRAMEGEN_FRAME_CNT_MOVING(dpu_crtc->fg); > > > > + dpu_tcon_set_operation_mode(dpu_crtc->tcon); > > > > + local_irq_restore(flags); > > > > + preempt_enable(); > > > > + > > > > + DPU_CRTC_WAIT_FOR_COMPLETION_TIMEOUT(ed_safe_shdld_done); > > > > + DPU_CRTC_WAIT_FOR_COMPLETION_TIMEOUT(ed_cont_shdld_done); > > > > + DPU_CRTC_WAIT_FOR_COMPLETION_TIMEOUT(dec_shdld_done); > > > > + > > > > + disable_irq(dpu_crtc->ed_safe_shdld_irq); > > > > + disable_irq(dpu_crtc->ed_cont_shdld_irq); > > > > + disable_irq(dpu_crtc->dec_shdld_irq); > > > > + > > > > + DPU_CRTC_WAIT_FOR_FRAMEGEN_SECONDARY_SYNCUP(dpu_crtc->fg); > > > > + > > > > + DPU_CRTC_CHECK_FRAMEGEN_FIFO(dpu_crtc->fg); > > > > + > > > > + dpu_crtc_queue_state_event(crtc); > > > > +} > > > > + > > > > +static void dpu_crtc_atomic_disable(struct drm_crtc *crtc, > > > > + struct drm_atomic_state *state) > > > > +{ > > > > + struct dpu_crtc *dpu_crtc = to_dpu_crtc(crtc); > > > > + struct drm_plane *plane; > > > > + struct drm_plane_state *old_plane_state; > > > > + struct dpu_plane_state *old_dpstate; > > > > + struct dpu_fetchunit *fu; > > > > + struct dpu_dprc *dprc; > > > > + const struct dpu_fetchunit_ops *fu_ops; > > > > + unsigned long flags; > > > > + int i; > > > > + > > > > + enable_irq(dpu_crtc->dec_seq_complete_irq); > > > > + > > > > + /* don't relinquish CPU until DPRC repeat_en is disabled */ > > > > + local_irq_save(flags); > > > > + preempt_disable(); > > > > + /* > > > > + * Sync to FrameGen frame counter moving so that > > > > + * FrameGen can be disabled in the next frame. > > > > + */ > > > > + DPU_CRTC_WAIT_FOR_FRAMEGEN_FRAME_CNT_MOVING(dpu_crtc->fg); > > > > + dpu_fg_disable(dpu_crtc->fg); > > > > + /* > > > > + * There is one frame leftover after FrameGen disablement. > > > > + * Sync to FrameGen frame counter moving so that > > > > + * DPRC repeat_en can be disabled in the next frame. > > > > + */ > > > > + DPU_CRTC_WAIT_FOR_FRAMEGEN_FRAME_CNT_MOVING(dpu_crtc->fg); > > > > + > > > > + for_each_old_plane_in_state(state, plane, old_plane_state, i) { > > > > + old_dpstate = to_dpu_plane_state(old_plane_state); > > > > + > > > > + if (!old_plane_state->fb) > > > > + continue; > > > > + > > > > + if (old_plane_state->crtc != crtc) > > > > + continue; > > > > + > > > > + fu = old_dpstate->source; > > > > + > > > > + fu_ops = dpu_fu_get_ops(fu); > > > > + > > > > + dprc = fu_ops->get_dprc(fu); > > > > + dpu_dprc_disable_repeat_en(dprc); > > > > + } > > > > + > > > > + local_irq_restore(flags); > > > > + preempt_enable(); > > > > + > > > > + DPU_CRTC_WAIT_FOR_COMPLETION_TIMEOUT(dec_seq_complete_done); > > > > + > > > > + disable_irq(dpu_crtc->dec_seq_complete_irq); > > > > + > > > > + dpu_fg_disable_clock(dpu_crtc->fg); > > > > + > > > > + drm_crtc_vblank_off(crtc); > > > > + > > > > + spin_lock_irq(&crtc->dev->event_lock); > > > > + if (crtc->state->event && !crtc->state->active) { > > > > + drm_crtc_send_vblank_event(crtc, crtc->state->event); > > > > + crtc->state->event = NULL; > > > > + } > > > > + spin_unlock_irq(&crtc->dev->event_lock); > > > > + > > > > + /* request power-off when CRTC is disabled */ > > > > + dpu_crtc_pm_runtime_put(crtc); > > > > +} > > > > + > > > > +static bool dpu_crtc_get_scanout_position(struct drm_crtc *crtc, > > > > + bool in_vblank_irq, > > > > + int *vpos, int *hpos, > > > > + ktime_t *stime, ktime_t *etime, > > > > + const struct drm_display_mode *mode) > > > > +{ > > > > + struct dpu_crtc *dpu_crtc = to_dpu_crtc(crtc); > > > > + int vdisplay = mode->crtc_vdisplay; > > > > + int vtotal = mode->crtc_vtotal; > > > > + int line; > > > > + bool reliable; > > > > + > > > > + if (stime) > > > > + *stime = ktime_get(); > > > > + > > > > + if (pm_runtime_active(dpu_crtc->dev->parent)) { > > > > + /* line index starts with 0 for the first active output line */ > > > > + line = dpu_fg_get_line_index(dpu_crtc->fg); > > > > + > > > > + if (line < vdisplay) > > > > + /* active scanout area - positive */ > > > > + *vpos = line + 1; > > > > + else > > > > + /* inside vblank - negative */ > > > > + *vpos = line - (vtotal - 1); > > > > + > > > > + reliable = true; > > > > + } else { > > > > + *vpos = 0; > > > > + reliable = false; > > > > + } > > > > + > > > > + *hpos = 0; > > > > + > > > > + if (etime) > > > > + *etime = ktime_get(); > > > > + > > > > + return reliable; > > > > +} > > > > + > > > > +static const struct drm_crtc_helper_funcs dpu_helper_funcs = { > > > > + .mode_valid = dpu_crtc_mode_valid, > > > > + .mode_set_nofb = dpu_crtc_mode_set_nofb, > > > > + .atomic_check = dpu_crtc_atomic_check, > > > > + .atomic_begin = dpu_crtc_atomic_begin, > > > > + .atomic_flush = dpu_crtc_atomic_flush, > > > > + .atomic_enable = dpu_crtc_atomic_enable, > > > > + .atomic_disable = dpu_crtc_atomic_disable, > > > > + .get_scanout_position = dpu_crtc_get_scanout_position, > > > > +}; > > > > + > > > > +static void dpu_crtc_put_resources(struct dpu_crtc *dpu_crtc) > > > > +{ > > > > +#define DPU_CRTC_PUT_RSC(unit) \ > > > > +do { \ > > > > + if (!IS_ERR_OR_NULL(dpu_crtc->unit)) \ > > > > + dpu_##unit##_put(dpu_crtc->unit); \ > > > > +} while (0) > > > > + > > > > + DPU_CRTC_PUT_RSC(cf_cont); > > > > + DPU_CRTC_PUT_RSC(cf_safe); > > > > + DPU_CRTC_PUT_RSC(dec); > > > > + DPU_CRTC_PUT_RSC(ed_cont); > > > > + DPU_CRTC_PUT_RSC(ed_safe); > > > > + DPU_CRTC_PUT_RSC(fg); > > > > + DPU_CRTC_PUT_RSC(gc); > > > > + DPU_CRTC_PUT_RSC(tcon); > > > > +} > > > > > > Here you could call the dpu_*_put() functions directly and add the > > > IS_ERR_OR_NULL() check at the beginning of the put() function itself. > > > > Will do. > > > > > > + > > > > +static int dpu_crtc_get_resources(struct dpu_crtc *dpu_crtc) > > > > +{ > > > > + struct dpu_soc *dpu = dev_get_drvdata(dpu_crtc->dev->parent); > > > > + int ret = 0; > > > > + > > > > +#define DPU_CRTC_GET_RSC(unit) \ > > > > +do { \ > > > > + dpu_crtc->unit = dpu_##unit##_get(dpu, dpu_crtc->stream_id); \ > > > > + if (IS_ERR(dpu_crtc->unit)) { \ > > > > + ret = PTR_ERR(dpu_crtc->unit); \ > > > > + goto err_out; \ > > > > + } \ > > > > +} while (0) > > > > + > > > > + DPU_CRTC_GET_RSC(cf_cont); > > > > + DPU_CRTC_GET_RSC(cf_safe); > > > > + DPU_CRTC_GET_RSC(dec); > > > > + DPU_CRTC_GET_RSC(ed_cont); > > > > + DPU_CRTC_GET_RSC(ed_safe); > > > > + DPU_CRTC_GET_RSC(fg); > > > > + DPU_CRTC_GET_RSC(gc); > > > > + DPU_CRTC_GET_RSC(tcon); > > > > > > This above could be rewritten like: > > > > > > ~~~ > > > int i; > > > struct { > > > void **dpu_unit; > > > void *(*get)(struct dpu_soc *dpu, unsigned int id); > > > } rsc[] = { > > > {(void *) &dpu_crtc->cf_cont, (void *) dpu_cf_cont_get}, > > > {(void *) &dpu_crtc->cf_safe, (void *) dpu_cf_safe_get}, > > > ... > > > }; > > > > > > for (i = 0; i < ARRAY_SIZE(rsc); i++) { > > > *rsc[i].dpu_unit = rsc[i].get(dpu, dpu_crtc->stream_id); > > > > > > if (IS_ERR(*rsc[i].dpu_unit)) { > > > ret = PTR_ERR(*rsc[i].dpu_unit); > > > goto err_out; > > > } > > > } > > > ~~~ > > > > > > I believe this should achieve the same result, but without macros. > > > > Will do. > > > > > > + > > > > + return ret; > > > > +err_out: > > > > + dpu_crtc_put_resources(dpu_crtc); > > > > + > > > > + return ret; > > > > +} > > > > + > > > > +static int dpu_crtc_init(struct dpu_crtc *dpu_crtc, > > > > + struct dpu_client_platformdata *pdata, > > > > + struct dpu_drm_device *dpu_drm) > > > > +{ > > > > + struct drm_device *drm = &dpu_drm->base; > > > > + struct dpu_soc *dpu = dev_get_drvdata(dpu_crtc->dev->parent); > > > > + struct drm_crtc *crtc = &dpu_crtc->base; > > > > + struct dpu_plane *dpu_plane; > > > > + struct dpu_crtc_grp *crtc_grp = pdata->crtc_grp; > > > > + struct dpu_plane_grp *plane_grp = crtc_grp->plane_grp; > > > > + unsigned int stream_id = pdata->stream_id; > > > > + unsigned int crtc_cnt; > > > > + int i, ret; > > > > + > > > > + init_completion(&dpu_crtc->dec_seq_complete_done); > > > > + init_completion(&dpu_crtc->dec_shdld_done); > > > > + init_completion(&dpu_crtc->ed_cont_shdld_done); > > > > + init_completion(&dpu_crtc->ed_safe_shdld_done); > > > > + > > > > + dpu_crtc->grp = crtc_grp; > > > > + dpu_crtc->stream_id = stream_id; > > > > + dpu_crtc->hw_plane_cnt = plane_grp->hw_plane_cnt; > > > > + > > > > + ret = dpu_crtc_get_resources(dpu_crtc); > > > > + if (ret) { > > > > + drm_err(drm, "failed to get HW resources for CRTC: %d\n", ret); > > > > + return ret; > > > > + } > > > > + > > > > + plane_grp->cf[stream_id] = dpu_crtc->cf_cont; > > > > + plane_grp->ed[stream_id] = dpu_crtc->ed_cont; > > > > + > > > > + /* each CRTC has a primary plane */ > > > > + dpu_plane = dpu_plane_initialize(drm, 0, plane_grp, > > > > + DRM_PLANE_TYPE_PRIMARY); > > > > + if (IS_ERR(dpu_plane)) { > > > > + ret = PTR_ERR(dpu_plane); > > > > + drm_err(drm, "failed to init primary plane: %d\n", ret); > > > > + goto err_put_resources; > > > > + } > > > > + > > > > + drm_crtc_helper_add(crtc, &dpu_helper_funcs); > > > > + > > > > + ret = drm_crtc_init_with_planes(drm, crtc, &dpu_plane->base, > > > > + NULL, &dpu_crtc_funcs, NULL); > > > > + if (ret) { > > > > + drm_err(drm, "failed to add CRTC: %d\n", ret); > > > > + goto err_put_resources; > > > > + } > > > > + > > > > + /* X server assumes 256 element gamma table so let's use that. */ > > > > + ret = drm_mode_crtc_set_gamma_size(crtc, 256); > > > > + if (ret) { > > > > + drm_err(drm, "failed to set CRTC gamma size: %d\n", ret); > > > > + goto err_put_resources; > > > > + } > > > > + > > > > + drm_crtc_enable_color_mgmt(crtc, 0, false, 256); > > > > + > > > > + dpu_crtc->encoder->possible_crtcs = drm_crtc_mask(crtc); > > > > + crtc_grp->crtc_mask |= drm_crtc_mask(crtc); > > > > + crtc_cnt = hweight32(crtc_grp->crtc_mask); > > > > + > > > > + /* initialize shared overlay planes for CRTCs in a CRTC group */ > > > > + if (crtc_cnt == DPU_CRTC_CNT_IN_GRP) { > > > > + /* > > > > + * All HW planes in a plane group are shared by CRTCs in a > > > > + * CRTC group. They will be assigned to either primary plane > > > > + * or overlay plane dynamically in runtime. Considering a > > > > + * CRTC consumes all HW planes and primary plane takes one > > > > + * HW plane, so overlay plane count for a CRTC group should > > > > + * be plane_grp->hw_plane_cnt - 1. > > > > + */ > > > > + for (i = 1; i < plane_grp->hw_plane_cnt; i++) { > > > > + dpu_plane = > > > > + dpu_plane_initialize(drm, crtc_grp->crtc_mask, > > > > + plane_grp, > > > > + DRM_PLANE_TYPE_OVERLAY); > > > > + if (IS_ERR(dpu_plane)) { > > > > + ret = PTR_ERR(dpu_plane); > > > > + drm_err(drm, > > > > + "failed to init overlay plane(%d): %d\n", > > > > + i, ret); > > > > + goto err_put_resources; > > > > + } > > > > + } > > > > + } > > > > + > > > > + ret = pm_runtime_get_sync(dpu_crtc->dev->parent); > > > > + if (ret < 0) { > > > > + pm_runtime_put_noidle(dpu_crtc->dev->parent); > > > > + drm_err(drm, "failed to get parent device RPM sync: %d\n", ret); > > > > + goto err_put_resources; > > > > + } > > > > + > > > > +#define DPU_CRTC_REQUEST_IRQ(name) \ > > > > +do { \ > > > > + dpu_crtc->name##_irq = dpu_map_irq(dpu, pdata->name##_irq); \ > > > > + irq_set_status_flags(dpu_crtc->name##_irq, IRQ_DISABLE_UNLAZY); \ > > > > + ret = devm_request_irq(dpu_crtc->dev, dpu_crtc->name##_irq, \ > > > > + dpu_crtc_##name##_irq_handler, \ > > > > + 0, dev_name(dpu_crtc->dev), dpu_crtc); \ > > > > + if (ret < 0) { \ > > > > + drm_err(drm, "failed to request irq(%u): %d\n", \ > > > > + dpu_crtc->name##_irq, ret); \ > > > > + goto err_put_pm_runtime; \ > > > > + } \ > > > > + disable_irq(dpu_crtc->name##_irq); \ > > > > +} while (0) > > > > Will drop this macro and request irqs by going through a local array. > > > > > > + > > > > + DPU_CRTC_REQUEST_IRQ(dec_frame_complete); > > > > + DPU_CRTC_REQUEST_IRQ(dec_seq_complete); > > > > + DPU_CRTC_REQUEST_IRQ(dec_shdld); > > > > + DPU_CRTC_REQUEST_IRQ(ed_cont_shdld); > > > > + DPU_CRTC_REQUEST_IRQ(ed_safe_shdld); > > > > + > > > > + ret = pm_runtime_put(dpu_crtc->dev->parent); > > > > + if (ret < 0) { > > > > + drm_err(drm, "failed to put parent device RPM: %d\n", ret); > > > > + dpu_crtc_put_resources(dpu_crtc); > > > > + } > > > > + > > > > + return ret; > > > > + > > > > +err_put_pm_runtime: > > > > + pm_runtime_put(dpu_crtc->dev->parent); > > > > +err_put_resources: > > > > + dpu_crtc_put_resources(dpu_crtc); > > > > + > > > > + return ret; > > > > +} > > > > + > > > > +static int dpu_crtc_bind(struct device *dev, struct device *master, void *data) > > > > +{ > > > > + struct dpu_client_platformdata *pdata = dev->platform_data; > > > > + struct dpu_drm_device *dpu_drm = data; > > > > + struct dpu_crtc *dpu_crtc; > > > > + bool found = false; > > > > + int ret; > > > > + > > > > + list_for_each_entry(dpu_crtc, &dpu_drm->crtc_list, node) { > > > > + if (dpu_crtc->np == dev->of_node) { > > > > + found = true; > > > > + break; > > > > + } > > > > + } > > > > + > > > > + if (!found) { > > > > + drm_err(&dpu_drm->base, "failed to find CRTC OF node\n"); > > > > + return -ENODEV; > > > > + } > > > > + > > > > + dpu_crtc->dev = dev; > > > > + > > > > + ret = dpu_crtc_init(dpu_crtc, pdata, dpu_drm); > > > > + if (ret) > > > > + return ret; > > > > + > > > > + dev_set_drvdata(dev, dpu_crtc); > > > > + > > > > + return ret; > > > > +} > > > > + > > > > +static void dpu_crtc_unbind(struct device *dev, struct device *master, > > > > + void *data) > > > > +{ > > > > + struct dpu_crtc *dpu_crtc = dev_get_drvdata(dev); > > > > + > > > > + dpu_crtc_put_resources(dpu_crtc); > > > > +} > > > > + > > > > +static const struct component_ops dpu_crtc_ops = { > > > > + .bind = dpu_crtc_bind, > > > > + .unbind = dpu_crtc_unbind, > > > > +}; > > > > + > > > > +static int dpu_crtc_probe(struct platform_device *pdev) > > > > +{ > > > > + struct device *dev = &pdev->dev; > > > > + > > > > + if (!dev->platform_data) > > > > + return -EINVAL; > > > > + > > > > + return component_add(dev, &dpu_crtc_ops); > > > > +} > > > > + > > > > +static int dpu_crtc_remove(struct platform_device *pdev) > > > > +{ > > > > + component_del(&pdev->dev, &dpu_crtc_ops); > > > > + return 0; > > > > +} > > > > + > > > > +struct platform_driver dpu_crtc_driver = { > > > > + .driver = { > > > > + .name = "imx-dpu-crtc", > > > > + }, > > > > + .probe = dpu_crtc_probe, > > > > + .remove = dpu_crtc_remove, > > > > +}; > > > > > > [...] > > > > > > > diff --git a/drivers/gpu/drm/imx/dpu/dpu-dprc.c b/drivers/gpu/drm/imx/dpu/dpu-dprc.c > > > > new file mode 100644 > > > > index 00000000..a543d0f > > > > --- /dev/null > > > > +++ b/drivers/gpu/drm/imx/dpu/dpu-dprc.c > > > > > > [...] > > > > > > > + > > > > +bool dpu_dprc_rtram_width_supported(struct dpu_dprc *dprc, unsigned int width) > > > > +{ > > > > + if (width > DPU_DPRC_MAX_RTRAM_WIDTH) > > > > + return false; > > > > + > > > > + return true; > > > > > > You can just 'return width < DPU_DPRC_MAX_RTRAM_WIDTH' here. > > > > Will use 'return width <= DPU_DPRC_MAX_RTRAM_WIDTH;'. > > > > > [...] > > > > > > > diff --git a/drivers/gpu/drm/imx/dpu/dpu-drv.c b/drivers/gpu/drm/imx/dpu/dpu-drv.c > > > > new file mode 100644 > > > > index 00000000..e85c4ec > > > > --- /dev/null > > > > +++ b/drivers/gpu/drm/imx/dpu/dpu-drv.c > > > > @@ -0,0 +1,297 @@ > > > > +// SPDX-License-Identifier: GPL-2.0+ > > > > + > > > > +/* > > > > + * Copyright 2019,2020 NXP > > > > + */ > > > > + > > > > +#include <linux/component.h> > > > > +#include <linux/dma-mapping.h> > > > > +#include <linux/kernel.h> > > > > +#include <linux/module.h> > > > > +#include <linux/of.h> > > > > +#include <linux/platform_device.h> > > > > + > > > > +#include <drm/drm_atomic_helper.h> > > > > +#include <drm/drm_drv.h> > > > > +#include <drm/drm_fb_helper.h> > > > > +#include <drm/drm_gem_cma_helper.h> > > > > +#include <drm/drm_modeset_helper.h> > > > > +#include <drm/drm_of.h> > > > > +#include <drm/drm_print.h> > > > > +#include <drm/drm_probe_helper.h> > > > > +#include <drm/drm_vblank.h> > > > > > > I didn't see any vblank related function called in dpu-drv.c. You could > > > remove drm_vblank.h. > > > > Will do. > > > > > > + > > > > +#include "dpu-drv.h" > > > > +#include "dpu-kms.h" > > > > + > > > > +#define DRIVER_NAME "imx-dpu-drm" > > > > > > [...] > > > > > > > diff --git a/drivers/gpu/drm/imx/dpu/dpu-kms.c b/drivers/gpu/drm/imx/dpu/dpu-kms.c > > > > new file mode 100644 > > > > index 00000000..876a7bb > > > > --- /dev/null > > > > +++ b/drivers/gpu/drm/imx/dpu/dpu-kms.c > > > > > > [...] > > > > > > > + > > > > +static int dpu_kms_init_encoder_per_crtc(struct drm_device *drm, > > > > + struct dpu_crtc *dpu_crtc) > > > > +{ > > > > + struct drm_encoder *encoder = dpu_crtc->encoder; > > > > + struct drm_bridge *bridge; > > > > + struct drm_connector *connector; > > > > + struct device_node *ep, *remote; > > > > + int ret = 0; > > > > + > > > > + ep = of_get_next_child(dpu_crtc->np, NULL); > > > > + if (!ep) { > > > > + drm_err(drm, "failed to find CRTC port's endpoint\n"); > > > > + return -ENODEV; > > > > + } > > > > + > > > > + remote = of_graph_get_remote_port_parent(ep); > > > > + if (!remote || !of_device_is_available(remote)) > > > > + goto out; > > > > + else if (!of_device_is_available(remote->parent)) > > > > + goto out; > > > > + > > > > + bridge = of_drm_find_bridge(remote); > > > > + if (!bridge) { > > > > + ret = -EPROBE_DEFER; > > > > + drm_dbg_kms(drm, "CRTC(%pOF) failed to find bridge: %d\n", > > > > + dpu_crtc->np, ret); > > > > + goto out; > > > > + } > > > > + > > > > + ret = drm_simple_encoder_init(drm, encoder, DRM_MODE_ENCODER_NONE); > > > > + if (ret) { > > > > + drm_err(drm, "failed to initialize encoder: %d\n", ret); > > > > + goto out; > > > > + } > > > > + > > > > + ret = drm_bridge_attach(encoder, bridge, NULL, > > > > + DRM_BRIDGE_ATTACH_NO_CONNECTOR); > > > > + if (ret) { > > > > + drm_err(drm, "failed to attach bridge to encoder: %d\n", ret); > > > > + goto out; > > > > + } > > > > + > > > > + connector = drm_bridge_connector_init(drm, encoder); > > > > + if (IS_ERR(connector)) { > > > > + ret = PTR_ERR(connector); > > > > + drm_err(drm, > > > > + "failed to initialize bridge connector: %d\n", ret); > > > > + goto out; > > > > + } > > > > + > > > > + ret = drm_connector_attach_encoder(connector, encoder); > > > > + if (ret) { > > > > + drm_err(drm, > > > > + "failed to attach encoder to connector: %d\n", ret); > > > > + goto out; > > > > > > You can remove this goto line. > > > > Will do. > > > > > > + } > > > > +out: > > > > + of_node_put(remote); > > > > + of_node_put(ep); > > > > + return ret; > > > > +} > > > > + > > > > +int dpu_kms_prepare(struct dpu_drm_device *dpu_drm, > > > > + struct list_head *crtc_np_list) > > > > +{ > > > > + struct drm_device *drm = &dpu_drm->base; > > > > + struct dpu_crtc_of_node *crtc_of_node; > > > > + struct dpu_crtc *crtc; > > > > + int ret, n_crtc = 0; > > > > + > > > > + INIT_LIST_HEAD(&dpu_drm->crtc_list); > > > > + > > > > + list_for_each_entry(crtc_of_node, crtc_np_list, list) { > > > > + crtc = drmm_kzalloc(drm, sizeof(*crtc), GFP_KERNEL); > > > > + if (!crtc) > > > > + return -ENOMEM; > > > > + > > > > + crtc->np = crtc_of_node->np; > > > > + > > > > + crtc->encoder = drmm_kzalloc(drm, sizeof(*crtc->encoder), > > > > + GFP_KERNEL); > > > > + if (!crtc->encoder) > > > > + return -ENOMEM; > > > > + > > > > + list_add(&crtc->node, &dpu_drm->crtc_list); > > > > + > > > > + n_crtc++; > > > > + } > > > > + > > > > + ret = drmm_mode_config_init(drm); > > > > + if (ret) > > > > + return ret; > > > > + > > > > + drm->mode_config.min_width = 60; > > > > + drm->mode_config.min_height = 60; > > > > + drm->mode_config.max_width = 8192; > > > > + drm->mode_config.max_height = 8192; > > > > + drm->mode_config.funcs = &dpu_drm_mode_config_funcs; > > > > + drm->mode_config.normalize_zpos = true; > > > > + drm->max_vblank_count = DPU_FRAMEGEN_MAX_FRAME_INDEX; > > > > + > > > > + list_for_each_entry(crtc, &dpu_drm->crtc_list, node) { > > > > + ret = dpu_kms_init_encoder_per_crtc(drm, crtc); > > > > + if (ret) > > > > + return ret; > > > > + } > > > > + > > > > + ret = drm_vblank_init(drm, n_crtc); > > > > + if (ret) { > > > > + drm_err(drm, "failed to initialize vblank support: %d\n", ret); > > > > + return ret; > > > > > > You can remove this return. > > > > Will do. > > > > > > + } > > > > + > > > > + return ret; > > > > +} > > > > > > [...] > > > > > > > diff --git a/drivers/gpu/drm/imx/dpu/dpu-plane.c b/drivers/gpu/drm/imx/dpu/dpu-plane.c > > > > new file mode 100644 > > > > index 00000000..ce85b9d > > > > --- /dev/null > > > > +++ b/drivers/gpu/drm/imx/dpu/dpu-plane.c > > > > > > [...] > > > > > > > + > > > > +static int dpu_plane_atomic_check(struct drm_plane *plane, > > > > + struct drm_plane_state *state) > > > > +{ > > > > + struct dpu_plane_state *dpstate = to_dpu_plane_state(state); > > > > + struct drm_crtc_state *crtc_state; > > > > + struct drm_framebuffer *fb = state->fb; > > > > + struct dpu_dprc *dprc; > > > > + const struct dpu_fetchunit_ops *fu_ops; > > > > + dma_addr_t baseaddr, uv_baseaddr; > > > > + u32 src_w, src_h, src_x, src_y, dst_w, dst_h; > > > > + int min_scale, bpp, ret; > > > > + bool fb_is_interlaced; > > > > + > > > > + /* ok to disable */ > > > > + if (!fb) { > > > > + dpstate->source = NULL; > > > > + dpstate->stage.ptr = NULL; > > > > + dpstate->blend = NULL; > > > > + return 0; > > > > + } > > > > + > > > > + if (!state->crtc) { > > > > + dpu_plane_dbg(plane, "no CRTC in plane state\n"); > > > > + return -EINVAL; > > > > + } > > > > + > > > > + crtc_state = > > > > + drm_atomic_get_existing_crtc_state(state->state, state->crtc); > > > > + if (WARN_ON(!crtc_state)) > > > > + return -EINVAL; > > > > + > > > > + min_scale = FRAC_16_16(1, DPU_PLANE_MAX_PIX_CNT_WITH_SCALER); > > > > + ret = drm_atomic_helper_check_plane_state(state, crtc_state, > > > > + min_scale, > > > > + DRM_PLANE_HELPER_NO_SCALING, > > > > + true, false); > > > > + if (ret) { > > > > + dpu_plane_dbg(plane, "failed to check plane state: %d\n", ret); > > > > + return ret; > > > > + } > > > > + > > > > + /* no off screen */ > > > > + if (state->dst.x1 < 0 || state->dst.y1 < 0 || > > > > + (state->dst.x2 > crtc_state->adjusted_mode.hdisplay) || > > > > + (state->dst.y2 > crtc_state->adjusted_mode.vdisplay)) { > > > > + dpu_plane_dbg(plane, "no off screen\n"); > > > > + return -EINVAL; > > > > + } > > > > + > > > > + fb_is_interlaced = !!(fb->flags & DRM_MODE_FB_INTERLACED); > > > > + > > > > + src_w = drm_rect_width(&state->src) >> 16; > > > > + src_h = drm_rect_height(&state->src) >> 16; > > > > + src_x = state->src.x1 >> 16; > > > > + src_y = state->src.y1 >> 16; > > > > + dst_w = drm_rect_width(&state->dst); > > > > + dst_h = drm_rect_height(&state->dst); > > > > + > > > > + /* max source resolution check */ > > > > + if (src_w == dst_w || src_h == dst_h) { > > > > + /* without scaling */ > > > > + if (src_w > DPU_PLANE_MAX_PIX_CNT || > > > > + src_h > DPU_PLANE_MAX_PIX_CNT) { > > > > + dpu_plane_dbg(plane, "invalid source resolution\n"); > > > > + return -EINVAL; > > > > + } > > > > + } else { > > > > + /* with scaling */ > > > > + if (src_w > DPU_PLANE_MAX_PIX_CNT_WITH_SCALER || > > > > + src_h > DPU_PLANE_MAX_PIX_CNT_WITH_SCALER) { > > > > + dpu_plane_dbg(plane, > > > > + "invalid source resolution with scale\n"); > > > > + return -EINVAL; > > > > + } > > > > + } > > > > + > > > > + /* pixel/line count and position parameters check */ > > > > + if (fb->format->hsub == 2) { > > > > + if (src_w % 2) { > > > > + dpu_plane_dbg(plane, "bad uv width\n"); > > > > + return -EINVAL; > > > > + } > > > > + if (src_x % 2) { > > > > + dpu_plane_dbg(plane, "bad uv xoffset\n"); > > > > + return -EINVAL; > > > > + } > > > > + } > > > > + if (fb->format->vsub == 2) { > > > > + if (src_h % (fb_is_interlaced ? 4 : 2)) { > > > > + dpu_plane_dbg(plane, "bad uv height\n"); > > > > + return -EINVAL; > > > > + } > > > > + if (src_y % (fb_is_interlaced ? 4 : 2)) { > > > > + dpu_plane_dbg(plane, "bad uv yoffset\n"); > > > > + return -EINVAL; > > > > + } > > > > + } > > > > + > > > > + if ((fb->flags & DRM_MODE_FB_MODIFIERS) && > > > > + !plane->funcs->format_mod_supported(plane, fb->format->format, > > > > + fb->modifier)) { > > > > + dpu_plane_dbg(plane, "invalid modifier 0x%016llx", > > > > + fb->modifier); > > > > + return -EINVAL; > > > > + } > > > > + > > > > + /* for tile formats, framebuffer has to be tile aligned */ > > > > + switch (fb->modifier) { > > > > + case DRM_FORMAT_MOD_VIVANTE_TILED: > > > > + if (fb->width % 4) { > > > > + dpu_plane_dbg(plane, "bad fb width for VIVANTE tile\n"); > > > > + return -EINVAL; > > > > + } > > > > + if (fb->height % 4) { > > > > + dpu_plane_dbg(plane, "bad fb height for VIVANTE tile\n"); > > > > + return -EINVAL; > > > > + } > > > > + break; > > > > + case DRM_FORMAT_MOD_VIVANTE_SUPER_TILED: > > > > + if (fb->width % 64) { > > > > + dpu_plane_dbg(plane, > > > > + "bad fb width for VIVANTE super tile\n"); > > > > + return -EINVAL; > > > > + } > > > > + if (fb->height % 64) { > > > > + dpu_plane_dbg(plane, > > > > + "bad fb height for VIVANTE super tile\n"); > > > > + return -EINVAL; > > > > + } > > > > + break; > > > > + } > > > > + > > > > + /* do not support BT709 full range */ > > > > + if (fb->format->is_yuv && > > > > + state->color_encoding == DRM_COLOR_YCBCR_BT709 && > > > > + state->color_range == DRM_COLOR_YCBCR_FULL_RANGE) { > > > > + dpu_plane_dbg(plane, "no BT709 full range support\n"); > > > > + return -EINVAL; > > > > + } > > > > + > > > > + /* base address alignment check */ > > > > + baseaddr = drm_plane_state_to_baseaddr(state); > > > > + switch (fb->format->format) { > > > > + case DRM_FORMAT_YUYV: > > > > + case DRM_FORMAT_UYVY: > > > > + bpp = 16; > > > > + break; > > > > + case DRM_FORMAT_NV12: > > > > + case DRM_FORMAT_NV21: > > > > + bpp = 8; > > > > + break; > > > > + default: > > > > + bpp = fb->format->cpp[0] * 8; > > > > + break; > > > > + } > > > > + if (((bpp == 32) && (baseaddr & 0x3)) || > > > > + ((bpp == 16) && (baseaddr & 0x1))) { > > > > + dpu_plane_dbg(plane, "%dbpp fb bad baddr alignment\n", bpp); > > > > + return -EINVAL; > > > > + } > > > > + switch (bpp) { > > > > + case 32: > > > > + if (baseaddr & 0x3) { > > > > + dpu_plane_dbg(plane, "32bpp fb bad baddr alignment\n"); > > > > + return -EINVAL; > > > > + } > > > > + break; > > > > + case 16: > > > > + if (fb->modifier) { > > > > + if (baseaddr & 0x1) { > > > > + dpu_plane_dbg(plane, > > > > + "16bpp tile fb bad baddr alignment\n"); > > > > + return -EINVAL; > > > > + } > > > > + } else { > > > > + if (baseaddr & 0x7) { > > > > + dpu_plane_dbg(plane, > > > > + "16bpp fb bad baddr alignment\n"); > > > > + return -EINVAL; > > > > + } > > > > + } > > > > + break; > > > > + } > > > > + > > > > + /* pitches[0] check */ > > > > + if (fb->pitches[0] > DPU_PLANE_MAX_PITCH) { > > > > + dpu_plane_dbg(plane, "fb pitches[0] is out of range\n"); > > > > + return -EINVAL; > > > > + } > > > > + > > > > + if (((bpp == 32) && (fb->pitches[0] & 0x3)) || > > > > + ((bpp == 16) && (fb->pitches[0] & 0x1))) { > > > > + dpu_plane_dbg(plane, > > > > + "%dbpp fb bad pitches[0] alignment\n", bpp); > > > > + return -EINVAL; > > > > + } > > > > + > > > > + /* UV planar check, assuming 16bpp */ > > > > + if (fb->format->num_planes > 1) { > > > > + /* base address alignment check */ > > > > + uv_baseaddr = drm_plane_state_to_uvbaseaddr(state); > > > > + if (uv_baseaddr & 0x7) { > > > > + dpu_plane_dbg(plane, "bad uv baddr alignment\n"); > > > > + return -EINVAL; > > > > + } > > > > + > > > > + /* pitches[1] check */ > > > > + if (fb->pitches[1] > DPU_PLANE_MAX_PITCH) { > > > > + dpu_plane_dbg(plane, "fb pitches[1] is out of range\n"); > > > > + return -EINVAL; > > > > + } > > > > + > > > > + if (fb->pitches[1] & 0x1) { > > > > + dpu_plane_dbg(plane, "fb bad pitches[1] alignment\n"); > > > > + return -EINVAL; > > > > + } > > > > + } > > > > + > > > > + /* DPRC check */ > > > > + fu_ops = dpu_fu_get_ops(dpstate->source); > > > > + dprc = fu_ops->get_dprc(dpstate->source); > > > > + > > > > + if (!dpu_dprc_rtram_width_supported(dprc, src_w)) { > > > > + dpu_plane_dbg(plane, "bad RTRAM width for DPRC\n"); > > > > + return -EINVAL; > > > > + } > > > > + > > > > + if (!dpu_dprc_stride_supported(dprc, fb->pitches[0], fb->pitches[1], > > > > + src_w, src_x, fb->format, fb->modifier, > > > > + baseaddr, uv_baseaddr)) { > > > > + dpu_plane_dbg(plane, "bad fb pitches for DPRC\n"); > > > > + return -EINVAL; > > > > + } > > > > + > > > > + return 0; > > > > +} > > > > > > This function is huge but it's well structured into logical sections. Why not > > > split it into smaller functions? > > > > Will do. > > > > > [...] > > > > > > > diff --git a/drivers/gpu/drm/imx/dpu/dpu-prv.h b/drivers/gpu/drm/imx/dpu/dpu-prv.h > > > > new file mode 100644 > > > > index 00000000..9151155 > > > > --- /dev/null > > > > +++ b/drivers/gpu/drm/imx/dpu/dpu-prv.h > > > > @@ -0,0 +1,203 @@ > > > > +/* SPDX-License-Identifier: GPL-2.0+ */ > > > > + > > > > +/* > > > > + * Copyright (C) 2016 Freescale Semiconductor, Inc. > > > > + * Copyright 2017-2020 NXP > > > > + */ > > > > + > > > > +#ifndef __DPU_PRV_H__ > > > > +#define __DPU_PRV_H__ > > > > + > > > > +#include <linux/clk.h> > > > > +#include <linux/device.h> > > > > +#include <linux/irqdomain.h> > > > > + > > > > +#include "dpu.h" > > > > + > > > > +/* DPU common control registers */ > > > > +#define DPU_COMCTRL_REG(offset) (offset) > > > > + > > > > +#define IPIDENTIFIER DPU_COMCTRL_REG(0x0) > > > > +#define LOCKUNLOCK DPU_COMCTRL_REG(0x40) > > > > +#define LOCKSTATUS DPU_COMCTRL_REG(0x44) > > > > +#define USERINTERRUPTMASK(n) DPU_COMCTRL_REG(0x48 + 4 * (n)) > > > > +#define INTERRUPTENABLE(n) DPU_COMCTRL_REG(0x50 + 4 * (n)) > > > > +#define INTERRUPTPRESET(n) DPU_COMCTRL_REG(0x58 + 4 * (n)) > > > > +#define INTERRUPTCLEAR(n) DPU_COMCTRL_REG(0x60 + 4 * (n)) > > > > +#define INTERRUPTSTATUS(n) DPU_COMCTRL_REG(0x68 + 4 * (n)) > > > > +#define USERINTERRUPTENABLE(n) DPU_COMCTRL_REG(0x80 + 4 * (n)) > > > > +#define USERINTERRUPTPRESET(n) DPU_COMCTRL_REG(0x88 + 4 * (n)) > > > > +#define USERINTERRUPTCLEAR(n) DPU_COMCTRL_REG(0x90 + 4 * (n)) > > > > +#define USERINTERRUPTSTATUS(n) DPU_COMCTRL_REG(0x98 + 4 * (n)) > > > > +#define GENERALPURPOSE DPU_COMCTRL_REG(0x100) > > > > + > > > > +#define DPU_SAFETY_STREAM_OFFSET 4 > > > > + > > > > +/* shadow enable bit for several DPU units */ > > > > +#define SHDEN BIT(0) > > > > + > > > > +/* Pixel Engine Configuration register fields */ > > > > +#define CLKEN_MASK_SHIFT 24 > > > > +#define CLKEN_MASK (0x3 << CLKEN_MASK_SHIFT) > > > > +#define CLKEN(n) ((n) << CLKEN_MASK_SHIFT) > > > > + > > > > +/* H/Vscaler register fields */ > > > > +#define SCALE_FACTOR_MASK 0xfffff > > > > +#define SCALE_FACTOR(n) ((n) & 0xfffff) > > > > +#define PHASE_OFFSET_MASK 0x1fffff > > > > +#define PHASE_OFFSET(n) ((n) & 0x1fffff) > > > > +#define OUTPUT_SIZE_MASK 0x3fff0000 > > > > +#define OUTPUT_SIZE(n) ((((n) - 1) << 16) & OUTPUT_SIZE_MASK) > > > > +#define FILTER_MODE_MASK 0x100 > > > > +#define FILTER_MODE(n) ((n) << 8) > > > > +#define SCALE_MODE_MASK 0x10 > > > > +#define SCALE_MODE(n) ((n) << 4) > > > > + > > > > +enum dpu_irq { > > > > + DPU_IRQ_STORE9_SHDLOAD = 0, > > > > + DPU_IRQ_STORE9_FRAMECOMPLETE = 1, > > > > + DPU_IRQ_STORE9_SEQCOMPLETE = 2, > > > > + DPU_IRQ_EXTDST0_SHDLOAD = 3, > > > > + DPU_IRQ_EXTDST0_FRAMECOMPLETE = 4, > > > > + DPU_IRQ_EXTDST0_SEQCOMPLETE = 5, > > > > + DPU_IRQ_EXTDST4_SHDLOAD = 6, > > > > + DPU_IRQ_EXTDST4_FRAMECOMPLETE = 7, > > > > + DPU_IRQ_EXTDST4_SEQCOMPLETE = 8, > > > > + DPU_IRQ_EXTDST1_SHDLOAD = 9, > > > > + DPU_IRQ_EXTDST1_FRAMECOMPLETE = 10, > > > > + DPU_IRQ_EXTDST1_SEQCOMPLETE = 11, > > > > + DPU_IRQ_EXTDST5_SHDLOAD = 12, > > > > + DPU_IRQ_EXTDST5_FRAMECOMPLETE = 13, > > > > + DPU_IRQ_EXTDST5_SEQCOMPLETE = 14, > > > > + DPU_IRQ_DISENGCFG_SHDLOAD0 = 15, > > > > + DPU_IRQ_DISENGCFG_FRAMECOMPLETE0 = 16, > > > > + DPU_IRQ_DISENGCFG_SEQCOMPLETE0 = 17, > > > > + DPU_IRQ_FRAMEGEN0_INT0 = 18, > > > > + DPU_IRQ_FRAMEGEN0_INT1 = 19, > > > > + DPU_IRQ_FRAMEGEN0_INT2 = 20, > > > > + DPU_IRQ_FRAMEGEN0_INT3 = 21, > > > > + DPU_IRQ_SIG0_SHDLOAD = 22, > > > > + DPU_IRQ_SIG0_VALID = 23, > > > > + DPU_IRQ_SIG0_ERROR = 24, > > > > + DPU_IRQ_DISENGCFG_SHDLOAD1 = 25, > > > > + DPU_IRQ_DISENGCFG_FRAMECOMPLETE1 = 26, > > > > + DPU_IRQ_DISENGCFG_SEQCOMPLETE1 = 27, > > > > + DPU_IRQ_FRAMEGEN1_INT0 = 28, > > > > + DPU_IRQ_FRAMEGEN1_INT1 = 29, > > > > + DPU_IRQ_FRAMEGEN1_INT2 = 30, > > > > + DPU_IRQ_FRAMEGEN1_INT3 = 31, > > > > + DPU_IRQ_SIG1_SHDLOAD = 32, > > > > + DPU_IRQ_SIG1_VALID = 33, > > > > + DPU_IRQ_SIG1_ERROR = 34, > > > > + DPU_IRQ_RESERVED = 35, > > > > + DPU_IRQ_CMDSEQ_ERROR = 36, > > > > + DPU_IRQ_COMCTRL_SW0 = 37, > > > > + DPU_IRQ_COMCTRL_SW1 = 38, > > > > + DPU_IRQ_COMCTRL_SW2 = 39, > > > > + DPU_IRQ_COMCTRL_SW3 = 40, > > > > + DPU_IRQ_FRAMEGEN0_PRIMSYNC_ON = 41, > > > > + DPU_IRQ_FRAMEGEN0_PRIMSYNC_OFF = 42, > > > > + DPU_IRQ_FRAMEGEN0_SECSYNC_ON = 43, > > > > + DPU_IRQ_FRAMEGEN0_SECSYNC_OFF = 44, > > > > + DPU_IRQ_FRAMEGEN1_PRIMSYNC_ON = 45, > > > > + DPU_IRQ_FRAMEGEN1_PRIMSYNC_OFF = 46, > > > > + DPU_IRQ_FRAMEGEN1_SECSYNC_ON = 47, > > > > + DPU_IRQ_FRAMEGEN1_SECSYNC_OFF = 48, > > > > + DPU_IRQ_COUNT = 49, > > > > +}; > > > > + > > > > +enum dpu_unit_type { > > > > + DPU_DISP, > > > > + DPU_BLIT, > > > > +}; > > > > + > > > > +struct dpu_units { > > > > + const unsigned int *ids; > > > > + const enum dpu_unit_type *types; > > > > + const unsigned long *ofss; > > > > + const unsigned long *pec_ofss; /* Pixel Engine Configuration */ > > > > + const unsigned int cnt; > > > > +}; > > > > + > > > > +struct dpu_soc { > > > > + struct device *dev; > > > > + > > > > + struct device *pd_dc_dev; > > > > + struct device *pd_pll0_dev; > > > > + struct device *pd_pll1_dev; > > > > + struct device_link *pd_dc_link; > > > > + struct device_link *pd_pll0_link; > > > > + struct device_link *pd_pll1_link; > > > > + > > > > + void __iomem *comctrl_reg; > > > > + > > > > + struct clk *clk_cfg; > > > > + struct clk *clk_axi; > > > > + > > > > + int id; > > > > + > > > > + int irq_disengcfg_framecomplete0; > > > > + int irq_disengcfg_seqcomplete0; > > > > + int irq_disengcfg_shdload0; > > > > + int irq_disengcfg_framecomplete1; > > > > + int irq_disengcfg_seqcomplete1; > > > > + int irq_disengcfg_shdload1; > > > > + int irq_extdst0_shdload; > > > > + int irq_extdst1_shdload; > > > > + int irq_extdst4_shdload; > > > > + int irq_extdst5_shdload; > > > > + > > > > + struct irq_domain *domain; > > > > + > > > > + struct dpu_constframe *cf_priv[4]; > > > > + struct dpu_disengcfg *dec_priv[2]; > > > > + struct dpu_extdst *ed_priv[4]; > > > > + struct dpu_fetchunit *fd_priv[3]; > > > > + struct dpu_fetchunit *fe_priv[4]; > > > > + struct dpu_framegen *fg_priv[2]; > > > > + struct dpu_fetchunit *fl_priv[1]; > > > > + struct dpu_fetchunit *fw_priv[2]; > > > > + struct dpu_gammacor *gc_priv[2]; > > > > + struct dpu_hscaler *hs_priv[3]; > > > > + struct dpu_layerblend *lb_priv[4]; > > > > + struct dpu_tcon *tcon_priv[2]; > > > > + struct dpu_vscaler *vs_priv[3]; > > > > +}; > > > > + > > > > +#define DECLARE_DPU_UNIT_HW_INIT_FUNC(unit) \ > > > > +void dpu_##unit##_hw_init(struct dpu_soc *dpu, unsigned int id) \ > > > > + > > > > +DECLARE_DPU_UNIT_HW_INIT_FUNC(cf); > > > > +DECLARE_DPU_UNIT_HW_INIT_FUNC(dec); > > > > +DECLARE_DPU_UNIT_HW_INIT_FUNC(ed); > > > > +DECLARE_DPU_UNIT_HW_INIT_FUNC(fd); > > > > +DECLARE_DPU_UNIT_HW_INIT_FUNC(fe); > > > > +DECLARE_DPU_UNIT_HW_INIT_FUNC(fg); > > > > +DECLARE_DPU_UNIT_HW_INIT_FUNC(fl); > > > > +DECLARE_DPU_UNIT_HW_INIT_FUNC(fw); > > > > +DECLARE_DPU_UNIT_HW_INIT_FUNC(gc); > > > > +DECLARE_DPU_UNIT_HW_INIT_FUNC(hs); > > > > +DECLARE_DPU_UNIT_HW_INIT_FUNC(lb); > > > > +DECLARE_DPU_UNIT_HW_INIT_FUNC(tcon); > > > > +DECLARE_DPU_UNIT_HW_INIT_FUNC(vs); > > > > > > Why use macros to declare these functions? It wouldn't make such a big > > > difference declaring them explicitly. > > > > I thought there would be some consistency if they can be declared by > > using the same pattern as DECLARE_DPU_UNIT_INIT_FUNC() below. Will > > declare them directly. > > > > > > + > > > > +#define DECLARE_DPU_UNIT_INIT_FUNC(unit) \ > > > > +int dpu_##unit##_init(struct dpu_soc *dpu, unsigned int index, \ > > > > + unsigned int id, enum dpu_unit_type type, \ > > > > + unsigned long pec_base, unsigned long base) > > > > + > > > > +DECLARE_DPU_UNIT_INIT_FUNC(cf); > > > > +DECLARE_DPU_UNIT_INIT_FUNC(dec); > > > > +DECLARE_DPU_UNIT_INIT_FUNC(ed); > > > > +DECLARE_DPU_UNIT_INIT_FUNC(fd); > > > > +DECLARE_DPU_UNIT_INIT_FUNC(fe); > > > > +DECLARE_DPU_UNIT_INIT_FUNC(fg); > > > > +DECLARE_DPU_UNIT_INIT_FUNC(fl); > > > > +DECLARE_DPU_UNIT_INIT_FUNC(fw); > > > > +DECLARE_DPU_UNIT_INIT_FUNC(gc); > > > > +DECLARE_DPU_UNIT_INIT_FUNC(hs); > > > > +DECLARE_DPU_UNIT_INIT_FUNC(lb); > > > > +DECLARE_DPU_UNIT_INIT_FUNC(tcon); > > > > +DECLARE_DPU_UNIT_INIT_FUNC(vs); > > > > > > Same question goes here. > > > > Each function has quite a few parameters, so it takes much more lines > > to declare them directly than by using the marco. Now that ctags + > > cscope doesn't do marco expansion, I will declare them directly. > > > > > > + > > > > +#endif /* __DPU_PRV_H__ */ > > > > diff --git a/drivers/gpu/drm/imx/dpu/dpu-tcon.c b/drivers/gpu/drm/imx/dpu/dpu-tcon.c > > > > new file mode 100644 > > > > index 00000000..e58dac8 > > > > --- /dev/null > > > > +++ b/drivers/gpu/drm/imx/dpu/dpu-tcon.c > > > > > > [...] > > > > > > > + > > > > +void dpu_tcon_hw_init(struct dpu_soc *dpu, unsigned int index) > > > > +{ > > > > + struct dpu_tcon *tcon = dpu->tcon_priv[index]; > > > > > > You can safely get rid of this extra variable. > > > > Will do. > > > > Regards, > > Liu Ying > > > > > Thanks, > > > laurentiu > > > > > > > + > > > > + /* reset TCON_CTRL to POR default so that TCON works in bypass mode */ > > > > + dpu_tcon_write(tcon, TCON_CTRL, CTRL_RST_VAL); > > > > +} > > > > +
