Re: [PATCH v2 2/3] arm64: dts: imx: Add i.mx8mm nitrogen8mm basic dts support

[Krzysztof Kozlowski <krzk@xxxxxxxxxx>]

On Wed, Jan 13, 2021 at 03:34:42PM +0100, Adrien Grassein wrote:
> Tested with a basic Build Root configuration booting from sdcard.
> 
> Signed-off-by: Adrien Grassein <adrien.grassein@xxxxxxxxx>
> ---
>  arch/arm64/boot/dts/freescale/Makefile        |   1 +
>  .../dts/freescale/imx8mm-nitrogen8mm_rev2.dts | 364 ++++++++++++++++++
>  2 files changed, 365 insertions(+)
>  create mode 100644 arch/arm64/boot/dts/freescale/imx8mm-nitrogen8mm_rev2.dts
> 
> diff --git a/arch/arm64/boot/dts/freescale/Makefile b/arch/arm64/boot/dts/freescale/Makefile
> index 901d80086b47..b2eb7a5e4db3 100644
> --- a/arch/arm64/boot/dts/freescale/Makefile
> +++ b/arch/arm64/boot/dts/freescale/Makefile
> @@ -45,6 +45,7 @@ dtb-$(CONFIG_ARCH_MXC) += imx8mq-librem5-devkit.dtb
>  dtb-$(CONFIG_ARCH_MXC) += imx8mq-librem5-r2.dtb
>  dtb-$(CONFIG_ARCH_MXC) += imx8mq-librem5-r3.dtb
>  dtb-$(CONFIG_ARCH_MXC) += imx8mq-nitrogen.dtb
> +dtb-$(CONFIG_ARCH_MXC) += imx8mm-nitrogen8mm_rev2.dtb
>  dtb-$(CONFIG_ARCH_MXC) += imx8mq-phanbell.dtb
>  dtb-$(CONFIG_ARCH_MXC) += imx8mq-pico-pi.dtb
>  dtb-$(CONFIG_ARCH_MXC) += imx8mq-thor96.dtb
> diff --git a/arch/arm64/boot/dts/freescale/imx8mm-nitrogen8mm_rev2.dts b/arch/arm64/boot/dts/freescale/imx8mm-nitrogen8mm_rev2.dts
> new file mode 100644
> index 000000000000..506e467ebf16
> --- /dev/null
> +++ b/arch/arm64/boot/dts/freescale/imx8mm-nitrogen8mm_rev2.dts
> @@ -0,0 +1,364 @@
> +// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
> +/*
> + * Device Tree file for Boundary Devices i.MX8MMini Nitrogen8MM Rev2 board.
> + * Adrien Grassein <adrien.grassein@xxxxxxxxxxxxx>
> + */
> +/dts-v1/;
> +#include "imx8mm.dtsi"
> +
> +/ {
> +	model = "Boundary Devices i.MX8MMini Nitrogen8MM Rev2";
> +	compatible = "boundary,imx8mm-nitrogen8mm", "fsl,imx8mm";
> +
> +	reg_vref_1v8: regulator-vref-1v8 {
> +		compatible = "regulator-fixed";
> +		regulator-name = "vref-1v8";
> +		regulator-min-microvolt = <1800000>;
> +		regulator-max-microvolt = <1800000>;
> +	};
> +
> +	reg_vref_3v3: regulator-vref-3v3 {
> +		compatible = "regulator-fixed";
> +		regulator-name = "vref-3v3";
> +		regulator-min-microvolt = <3300000>;
> +		regulator-max-microvolt = <3300000>;
> +	};

Why do you need these two regulators? They don't do anything, there is
no control over them.

> +};
> +
> +&A53_0 {
> +	cpu-supply = <&reg_sw3>;
> +};
> +
> +&A53_1 {
> +	cpu-supply = <&reg_sw3>;
> +};
> +
> +&A53_2 {
> +	cpu-supply = <&reg_sw3>;
> +};
> +
> +&A53_3 {
> +	cpu-supply = <&reg_sw3>;
> +};
> +
> +&i2c1 {
> +	clock-frequency = <400000>;
> +	pinctrl-names = "default", "gpio";
> +	pinctrl-0 = <&pinctrl_i2c1>;
> +	pinctrl-1 = <&pinctrl_i2c1_1>;
> +	scl-gpios = <&gpio5 14 GPIO_OPEN_DRAIN>;
> +	sda-gpios = <&gpio5 15 GPIO_OPEN_DRAIN>;
> +	status = "okay";
> +
> +	pmic@8 {
> +		compatible = "nxp,pf8121a";
> +		reg = <0x8>;
> +		status = "okay";
> +
> +		regulators {
> +			reg_ldo2: ldo2 {

The PMIC regulators should be described fully, so bring them back from
the v1.

> +				regulator-always-on;
> +				regulator-boot-on;
> +				regulator-max-microvolt = <5000000>;
> +				regulator-min-microvolt = <1500000>;
> +			};
> +
> +			reg_sw3: buck3 {
> +				regulator-always-on;
> +				regulator-boot-on;
> +				regulator-max-microvolt = <1800000>;
> +				regulator-min-microvolt =  <400000>;
> +			};
> +		};
> +	};
> +};
> +
> +&fec1 {

Please order the overridden nodes alphabetically, with iomux exception
which goes to the end (by convention in NXP). You define i2c1, then fec1
and then i2c3. Should be fec1, i2c1 and then i2c3.

Best regards,
Krzysztof