On 1/12/2021 5:17 AM, Rafał Miłecki wrote:
> From: Rafał Miłecki <rafal@xxxxxxxxxx>
>
> BCM4908 has internal switch with 5 GPHYs. Ports 0 - 3 are always
> connected to the internal PHYs. Remaining ports depend on device setup.
>
> Asus GT-AC5300 has an extra switch with its PHYs accessible using the
> internal MDIO.
>
> CPU port and Ethernet interface remain to be documented.
>
> Signed-off-by: Rafał Miłecki <rafal@xxxxxxxxxx>
> ---
> .../bcm4908/bcm4908-asus-gt-ac5300.dts | 51 +++++++++++
> .../boot/dts/broadcom/bcm4908/bcm4908.dtsi | 85 ++++++++++++++++++-
> 2 files changed, 135 insertions(+), 1 deletion(-)
>
> diff --git a/arch/arm64/boot/dts/broadcom/bcm4908/bcm4908-asus-gt-ac5300.dts b/arch/arm64/boot/dts/broadcom/bcm4908/bcm4908-asus-gt-ac5300.dts
> index 13c6b86eef21..51305e96fbd6 100644
> --- a/arch/arm64/boot/dts/broadcom/bcm4908/bcm4908-asus-gt-ac5300.dts
> +++ b/arch/arm64/boot/dts/broadcom/bcm4908/bcm4908-asus-gt-ac5300.dts
> @@ -44,6 +44,57 @@ brightness {
> };
> };
>
> +&ports {
> + port@0 {
> + label = "lan2";
> + };
> +
> + port@1 {
> + label = "lan1";
> + };
> +
> + port@2 {
> + label = "lan6";
> + };
> +
> + port@3 {
> + label = "lan5";
> + };
> +
> + /* External BCM53134S switch */
> + port@7 {
> + label = "sw";
> + reg = <7>;
> +
> + fixed-link {
> + speed = <1000>;
> + full-duplex;
> + };
> + };
> +};
> +
> +&mdio {
> + /* lan8 */
> + phy@0 {
> + reg = <0>;
> + };
> +
> + /* lan7 */
> + phy@1 {
> + reg = <1>;
> + };
> +
> + /* lan4 */
> + phy@2 {
> + reg = <2>;
> + };
> +
> + /* lan3 */
> + phy@3 {
> + reg = <3>;
> + };
> +};
> +
> &nandcs {
> nand-ecc-strength = <4>;
> nand-ecc-step-size = <512>;
> diff --git a/arch/arm64/boot/dts/broadcom/bcm4908/bcm4908.dtsi b/arch/arm64/boot/dts/broadcom/bcm4908/bcm4908.dtsi
> index b5b772a9a51b..0b44f32fdef1 100644
> --- a/arch/arm64/boot/dts/broadcom/bcm4908/bcm4908.dtsi
> +++ b/arch/arm64/boot/dts/broadcom/bcm4908/bcm4908.dtsi
> @@ -108,7 +108,7 @@ soc {
> compatible = "simple-bus";
> #address-cells = <1>;
> #size-cells = <1>;
> - ranges = <0x00 0x00 0x80000000 0x10000>;
> + ranges = <0x00 0x00 0x80000000 0xd0000>;
>
> usb@c300 {
> compatible = "generic-ehci";
> @@ -130,6 +130,89 @@ usb@d000 {
> interrupts = <GIC_SPI 74 IRQ_TYPE_LEVEL_HIGH>;
> status = "disabled";
> };
> +
> + switch@80000 {
> + compatible = "simple-mfd";
Should not this be simple-bus instead? That is what I used in the 7445
and 7278 Device Trees provided by the bootloader, and also what was in
the sf2 example binding.
> + #size-cells = <1>;
> + #address-cells = <1>;
> + ranges = <0 0x80000 0x50000>;
> +
> + switch@0 {
> + compatible = "brcm,bcm4908-switch";
> + reg = <0x0 0x40000>,
> + <0x40000 0x110>,
> + <0x40340 0x30>,
> + <0x40380 0x30>,
> + <0x40600 0x34>,
> + <0x40800 0x208>;
> + reg-names = "core", "reg", "intrl2_0",
> + "intrl2_1", "fcb", "acb";
> + interrupts = <GIC_SPI 57 IRQ_TYPE_LEVEL_HIGH>,
> + <GIC_SPI 58 IRQ_TYPE_LEVEL_HIGH>;
> + brcm,num-gphy = <5>;
> + brcm,num-rgmii-ports = <2>;
> +
> + #address-cells = <1>;
> + #size-cells = <0>;
> +
> + ports: ports {
> + #address-cells = <1>;
> + #size-cells = <0>;
> +
> + port@0 {
> + reg = <0>;
> + phy-mode = "internal";
> + phy-handle = <&phy8>;
> + };
> +
> + port@1 {
> + reg = <1>;
> + phy-mode = "internal";
> + phy-handle = <&phy9>;
> + };
> +
> + port@2 {
> + reg = <2>;
> + phy-mode = "internal";
> + phy-handle = <&phy10>;
> + };
> +
> + port@3 {
> + reg = <3>;
> + phy-mode = "internal";
> + phy-handle = <&phy11>;
> + };
> + };
> + };
> +
> + mdio: mdio@405c0 {
> + compatible = "brcm,unimac-mdio";
> + reg = <0x405c0 0x8>;
> + reg-names = "mdio";
> + #size-cells = <1>;
> + #address-cells = <0>;
> +
> + phy8: phy@8 {
> + reg = <8>;
> + };
> +
> + phy9: phy@9 {
> + reg = <9>;
> + };
> +
> + phy10: phy@a {
> + reg = <10>;
> + };
> +
> + phy11: phy@b {
> + reg = <11>;
> + };
> +
> + phy12: phy@c {
> + reg = <12>;
> + };
> + };
> + };
> };
>
> bus@ff800000 {
>
--
Florian
