On Fri, Dec 11, 2020 at 02:48:55PM +0100, Teresa Remmet wrote:
> Add initial support for phyBOARD-Pollux-i.MX8MP.
> Supported basic features:
> * eMMC
> * i2c EEPROM
> * i2c RTC
> * i2c LED
> * PMIC
> * debug UART
> * SD card
> * 1Gbit Ethernet (fec)
> * watchdog
>
> Signed-off-by: Teresa Remmet <t.remmet@xxxxxxxxx>
> Reviewed-by: Krzysztof Kozlowski <krzk@xxxxxxxxxx>
> ---
> arch/arm64/boot/dts/freescale/Makefile | 1 +
> .../dts/freescale/imx8mp-phyboard-pollux-rdk.dts | 163 ++++++++++++
> .../boot/dts/freescale/imx8mp-phycore-som.dtsi | 296 +++++++++++++++++++++
> 3 files changed, 460 insertions(+)
> create mode 100644 arch/arm64/boot/dts/freescale/imx8mp-phyboard-pollux-rdk.dts
> create mode 100644 arch/arm64/boot/dts/freescale/imx8mp-phycore-som.dtsi
>
> diff --git a/arch/arm64/boot/dts/freescale/Makefile b/arch/arm64/boot/dts/freescale/Makefile
> index acfb8af45912..a43b496678be 100644
> --- a/arch/arm64/boot/dts/freescale/Makefile
> +++ b/arch/arm64/boot/dts/freescale/Makefile
> @@ -37,6 +37,7 @@ dtb-$(CONFIG_ARCH_MXC) += imx8mn-evk.dtb
> dtb-$(CONFIG_ARCH_MXC) += imx8mn-ddr4-evk.dtb
> dtb-$(CONFIG_ARCH_MXC) += imx8mn-var-som-symphony.dtb
> dtb-$(CONFIG_ARCH_MXC) += imx8mp-evk.dtb
> +dtb-$(CONFIG_ARCH_MXC) += imx8mp-phyboard-pollux-rdk.dtb
> dtb-$(CONFIG_ARCH_MXC) += imx8mq-evk.dtb
> dtb-$(CONFIG_ARCH_MXC) += imx8mq-hummingboard-pulse.dtb
> dtb-$(CONFIG_ARCH_MXC) += imx8mq-librem5-devkit.dtb
> diff --git a/arch/arm64/boot/dts/freescale/imx8mp-phyboard-pollux-rdk.dts b/arch/arm64/boot/dts/freescale/imx8mp-phyboard-pollux-rdk.dts
> new file mode 100644
> index 000000000000..e92868c10526
> --- /dev/null
> +++ b/arch/arm64/boot/dts/freescale/imx8mp-phyboard-pollux-rdk.dts
> @@ -0,0 +1,163 @@
> +// SPDX-License-Identifier: GPL-2.0
> +/*
> + * Copyright (C) 2020 PHYTEC Messtechnik GmbH
> + * Author: Teresa Remmet <t.remmet@xxxxxxxxx>
> + */
> +
> +/dts-v1/;
> +
> +#include <dt-bindings/leds/leds-pca9532.h>
> +#include <dt-bindings/pwm/pwm.h>
> +#include "imx8mp-phycore-som.dtsi"
> +
> +/ {
> + model = "PHYTEC phyBOARD-Pollux i.MX8MP";
> + compatible = "phytec,imx8mp-phyboard-pollux-rdk",
> + "phytec,imx8mp-phycore-som", "fsl,imx8mp";
> +
> + chosen {
> + stdout-path = &uart2;
> + };
> +
> + reg_usdhc2_vmmc: regulator-usdhc2 {
> + compatible = "regulator-fixed";
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_reg_usdhc2_vmmc>;
> + regulator-name = "VSD_3V3";
> + regulator-min-microvolt = <3300000>;
> + regulator-max-microvolt = <3300000>;
> + gpio = <&gpio2 19 GPIO_ACTIVE_HIGH>;
> + enable-active-high;
> + startup-delay-us = <100>;
> + off-on-delay-us = <12000>;
> + };
> +};
> +
> +&i2c2 {
> + clock-frequency = <400000>;
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_i2c2>;
> + pinctrl-1 = <&pinctrl_i2c2_gpio>;
> + sda-gpios = <&gpio5 17 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
> + scl-gpios = <&gpio5 16 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
> + status = "okay";
> +
> + eeprom@51 {
> + compatible = "atmel,24c02";
> + reg = <0x51>;
> + pagesize = <16>;
> + status = "okay";
We generally use 'okay' to flip the 'disabled' status defined in
<soc>.dtsi. It's only really needed for such cases.
> + };
> +
> + leds@62 {
> + compatible = "nxp,pca9533";
> + reg = <0x62>;
> + status = "okay";
Ditto
> +
> + led1 {
> + type = <PCA9532_TYPE_LED>;
> + };
> +
> + led2 {
> + type = <PCA9532_TYPE_LED>;
> + };
> +
> + led3 {
> + type = <PCA9532_TYPE_LED>;
> + };
> + };
> +};
> +
> +&snvs_pwrkey {
> + status = "okay";
> +};
> +
> +/* debug console */
> +&uart2 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_uart2>;
> + status = "okay";
> +};
> +
> +/* SD-Card */
> +&usdhc2 {
> + pinctrl-names = "default", "state_100mhz", "state_200mhz";
> + pinctrl-0 = <&pinctrl_usdhc2>, <&pinctrl_usdhc2_pins>;
> + pinctrl-1 = <&pinctrl_usdhc2_100mhz>, <&pinctrl_usdhc2_pins>;
> + pinctrl-2 = <&pinctrl_usdhc2_200mhz>, <&pinctrl_usdhc2_pins>;
> + cd-gpios = <&gpio2 12 GPIO_ACTIVE_LOW>;
> + vmmc-supply = <®_usdhc2_vmmc>;
> + bus-width = <4>;
> + status = "okay";
> +};
> +
> +&iomuxc {
> + pinctrl_i2c2: i2c2grp {
> + fsl,pins = <
> + MX8MP_IOMUXC_I2C2_SCL__I2C2_SCL 0x400001c3
> + MX8MP_IOMUXC_I2C2_SDA__I2C2_SDA 0x400001c3
> + >;
> + };
> +
> + pinctrl_i2c2_gpio: i2c2gpiogrp {
> + fsl,pins = <
> + MX8MP_IOMUXC_I2C2_SCL__GPIO5_IO16 0x1e3
> + MX8MP_IOMUXC_I2C2_SDA__GPIO5_IO17 0x1e3
> + >;
> + };
> +
> + pinctrl_reg_usdhc2_vmmc: regusdhc2vmmcgrp {
> + fsl,pins = <
> + MX8MP_IOMUXC_SD2_RESET_B__GPIO2_IO19 0x41
> + >;
> + };
> +
> + pinctrl_uart2: uart2grp {
> + fsl,pins = <
> + MX8MP_IOMUXC_UART2_RXD__UART2_DCE_RX 0x49
> + MX8MP_IOMUXC_UART2_TXD__UART2_DCE_TX 0x49
> + >;
> + };
> +
> + pinctrl_usdhc2_pins: usdhc2-gpiogrp {
> + fsl,pins = <
> + MX8MP_IOMUXC_SD2_CD_B__GPIO2_IO12 0x1c4
> + >;
> + };
> +
> + pinctrl_usdhc2: usdhc2grp {
> + fsl,pins = <
> + MX8MP_IOMUXC_SD2_CLK__USDHC2_CLK 0x190
> + MX8MP_IOMUXC_SD2_CMD__USDHC2_CMD 0x1d0
> + MX8MP_IOMUXC_SD2_DATA0__USDHC2_DATA0 0x1d0
> + MX8MP_IOMUXC_SD2_DATA1__USDHC2_DATA1 0x1d0
> + MX8MP_IOMUXC_SD2_DATA2__USDHC2_DATA2 0x1d0
> + MX8MP_IOMUXC_SD2_DATA3__USDHC2_DATA3 0x1d0
> + MX8MP_IOMUXC_GPIO1_IO04__USDHC2_VSELECT 0xc1
> + >;
> + };
> +
> + pinctrl_usdhc2_100mhz: usdhc2-100mhzgrp {
> + fsl,pins = <
> + MX8MP_IOMUXC_SD2_CLK__USDHC2_CLK 0x194
> + MX8MP_IOMUXC_SD2_CMD__USDHC2_CMD 0x1d4
> + MX8MP_IOMUXC_SD2_DATA0__USDHC2_DATA0 0x1d4
> + MX8MP_IOMUXC_SD2_DATA1__USDHC2_DATA1 0x1d4
> + MX8MP_IOMUXC_SD2_DATA2__USDHC2_DATA2 0x1d4
> + MX8MP_IOMUXC_SD2_DATA3__USDHC2_DATA3 0x1d4
> + MX8MP_IOMUXC_GPIO1_IO04__USDHC2_VSELECT 0xc1
> + >;
> + };
> +
> + pinctrl_usdhc2_200mhz: usdhc2-200mhzgrp {
> + fsl,pins = <
> + MX8MP_IOMUXC_SD2_CLK__USDHC2_CLK 0x196
> + MX8MP_IOMUXC_SD2_CMD__USDHC2_CMD 0x1d6
> + MX8MP_IOMUXC_SD2_DATA0__USDHC2_DATA0 0x1d6
> + MX8MP_IOMUXC_SD2_DATA1__USDHC2_DATA1 0x1d6
> + MX8MP_IOMUXC_SD2_DATA2__USDHC2_DATA2 0x1d6
> + MX8MP_IOMUXC_SD2_DATA3__USDHC2_DATA3 0x1d6
> + MX8MP_IOMUXC_GPIO1_IO04__USDHC2_VSELECT 0xc1
> + >;
> + };
> +};
> diff --git a/arch/arm64/boot/dts/freescale/imx8mp-phycore-som.dtsi b/arch/arm64/boot/dts/freescale/imx8mp-phycore-som.dtsi
> new file mode 100644
> index 000000000000..8618df68b1e5
> --- /dev/null
> +++ b/arch/arm64/boot/dts/freescale/imx8mp-phycore-som.dtsi
> @@ -0,0 +1,296 @@
> +// SPDX-License-Identifier: GPL-2.0
> +/*
> + * Copyright (C) 2020 PHYTEC Messtechnik GmbH
> + * Author: Teresa Remmet <t.remmet@xxxxxxxxx>
> + */
> +
> +#include <dt-bindings/net/ti-dp83867.h>
> +#include "imx8mp.dtsi"
> +
> +/ {
> + model = "PHYTEC phyCORE-i.MX8MP";
> + compatible = "phytec,imx8mp-phycore-som", "fsl,imx8mp";
> +
> + aliases {
> + rtc0 = &rv3028;
> + rtc1 = &snvs_rtc;
> + };
> +
> + memory@40000000 {
> + device_type = "memory";
> + reg = <0x0 0x40000000 0 0x80000000>;
> + };
> +};
> +
> +&A53_0 {
> + cpu-supply = <&buck2>;
> +};
> +
> +&A53_1 {
> + cpu-supply = <&buck2>;
> +};
> +
> +&A53_2 {
> + cpu-supply = <&buck2>;
> +};
> +
> +&A53_3 {
> + cpu-supply = <&buck2>;
> +};
> +
> +/* ethernet 1 */
> +&fec {
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_fec>;
> + phy-mode = "rgmii-id";
> + phy-handle = <ðphy1>;
> + fsl,magic-packet;
> + status = "okay";
> +
> + mdio {
> + #address-cells = <1>;
> + #size-cells = <0>;
> +
> + ethphy1: ethernet-phy@0 {
> + compatible = "ethernet-phy-ieee802.3-c22";
> + reg = <0>;
> + interrupt-parent = <&gpio1>;
> + interrupts = <15 IRQ_TYPE_EDGE_FALLING>;
> + ti,rx-internal-delay = <DP83867_RGMIIDCTL_2_00_NS>;
> + ti,tx-internal-delay = <DP83867_RGMIIDCTL_2_00_NS>;
> + ti,fifo-depth = <DP83867_PHYCR_FIFO_DEPTH_4_B_NIB>;
> + ti,clk-output-sel = <DP83867_CLK_O_SEL_OFF>;
> + enet-phy-lane-no-swap;
Undocumented property?
> + };
> + };
> +};
> +
> +&i2c1 {
> + clock-frequency = <400000>;
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_i2c1>;
> + pinctrl-1 = <&pinctrl_i2c1_gpio>;
> + sda-gpios = <&gpio5 15 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
> + scl-gpios = <&gpio5 14 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
> + status = "okay";
> +
> + pmic: pmic@25 {
> + reg = <0x25>;
> + compatible = "nxp,pca9450c";
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_pmic>;
> + interrupt-parent = <&gpio4>;
> + interrupts = <18 IRQ_TYPE_LEVEL_LOW>;
> +
> + regulators {
> + buck1: BUCK1 {
> + regulator-compatible = "BUCK1";
> + regulator-min-microvolt = <600000>;
> + regulator-max-microvolt = <2187500>;
> + regulator-boot-on;
> + regulator-always-on;
> + regulator-ramp-delay = <3125>;
> + };
> +
> + buck2: BUCK2 {
> + regulator-compatible = "BUCK2";
> + regulator-min-microvolt = <600000>;
> + regulator-max-microvolt = <2187500>;
> + regulator-boot-on;
> + regulator-always-on;
> + regulator-ramp-delay = <3125>;
> + };
> +
> + buck4: BUCK4 {
> + regulator-compatible = "BUCK4";
> + regulator-min-microvolt = <600000>;
> + regulator-max-microvolt = <3400000>;
> + regulator-boot-on;
> + regulator-always-on;
> + };
> +
> + buck5: BUCK5 {
> + regulator-compatible = "BUCK5";
> + regulator-min-microvolt = <600000>;
> + regulator-max-microvolt = <3400000>;
> + regulator-boot-on;
> + regulator-always-on;
> + };
> +
> + buck6: BUCK6 {
> + regulator-compatible = "BUCK6";
> + regulator-min-microvolt = <600000>;
> + regulator-max-microvolt = <3400000>;
> + regulator-boot-on;
> + regulator-always-on;
> + };
> +
> + ldo1: LDO1 {
> + regulator-compatible = "LDO1";
> + regulator-min-microvolt = <1600000>;
> + regulator-max-microvolt = <3300000>;
> + regulator-boot-on;
> + regulator-always-on;
> + };
> +
> + ldo2: LDO2 {
> + regulator-compatible = "LDO2";
> + regulator-min-microvolt = <800000>;
> + regulator-max-microvolt = <1150000>;
> + regulator-boot-on;
> + regulator-always-on;
> + };
> +
> + ldo3: LDO3 {
> + regulator-compatible = "LDO3";
> + regulator-min-microvolt = <800000>;
> + regulator-max-microvolt = <3300000>;
> + regulator-boot-on;
> + regulator-always-on;
> + };
> +
> + ldo4: LDO4 {
> + regulator-compatible = "LDO4";
> + regulator-min-microvolt = <800000>;
> + regulator-max-microvolt = <3300000>;
> + regulator-boot-on;
> + regulator-always-on;
> + };
> +
> + ldo5: LDO5 {
> + regulator-compatible = "LDO5";
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <3300000>;
> + };
> + };
> + };
> +
> + eeprom@51 {
> + compatible = "atmel,24c32";
> + reg = <0x51>;
> + pagesize = <32>;
> + status = "okay";
Unneeded 'okay' status.
> + };
> +
> + rv3028: rtc@52 {
> + compatible = "microcrystal,rv3028";
> + reg = <0x52>;
> + trickle-resistor-ohms = <1000>;
> + enable-level-switching-mode;
Undocumented property?
Shawn
> + status = "okay";
> + };
> +};
> +
> +/* eMMC */
> +&usdhc3 {
> + pinctrl-names = "default", "state_100mhz", "state_200mhz";
> + pinctrl-0 = <&pinctrl_usdhc3>;
> + pinctrl-1 = <&pinctrl_usdhc3_100mhz>;
> + pinctrl-2 = <&pinctrl_usdhc3_200mhz>;
> + bus-width = <8>;
> + non-removable;
> + status = "okay";
> +};
> +
> +&wdog1 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_wdog>;
> + fsl,ext-reset-output;
> + status = "okay";
> +};
> +
> +&iomuxc {
> + pinctrl_fec: fecgrp {
> + fsl,pins = <
> + MX8MP_IOMUXC_SAI1_RXD2__ENET1_MDC 0x3
> + MX8MP_IOMUXC_SAI1_RXD3__ENET1_MDIO 0x3
> + MX8MP_IOMUXC_SAI1_RXD4__ENET1_RGMII_RD0 0x91
> + MX8MP_IOMUXC_SAI1_RXD5__ENET1_RGMII_RD1 0x91
> + MX8MP_IOMUXC_SAI1_RXD6__ENET1_RGMII_RD2 0x91
> + MX8MP_IOMUXC_SAI1_RXD7__ENET1_RGMII_RD3 0x91
> + MX8MP_IOMUXC_SAI1_TXC__ENET1_RGMII_RXC 0x91
> + MX8MP_IOMUXC_SAI1_TXFS__ENET1_RGMII_RX_CTL 0x91
> + MX8MP_IOMUXC_SAI1_TXD0__ENET1_RGMII_TD0 0x1f
> + MX8MP_IOMUXC_SAI1_TXD1__ENET1_RGMII_TD1 0x1f
> + MX8MP_IOMUXC_SAI1_TXD2__ENET1_RGMII_TD2 0x1f
> + MX8MP_IOMUXC_SAI1_TXD3__ENET1_RGMII_TD3 0x1f
> + MX8MP_IOMUXC_SAI1_TXD4__ENET1_RGMII_TX_CTL 0x1f
> + MX8MP_IOMUXC_SAI1_TXD5__ENET1_RGMII_TXC 0x1f
> + MX8MP_IOMUXC_GPIO1_IO15__GPIO1_IO15 0x11
> + >;
> + };
> +
> + pinctrl_i2c1: i2c1grp {
> + fsl,pins = <
> + MX8MP_IOMUXC_I2C1_SCL__I2C1_SCL 0x400001c3
> + MX8MP_IOMUXC_I2C1_SDA__I2C1_SDA 0x400001c3
> + >;
> + };
> +
> + pinctrl_i2c1_gpio: i2c1gpiogrp {
> + fsl,pins = <
> + MX8MP_IOMUXC_I2C1_SCL__GPIO5_IO14 0x1e3
> + MX8MP_IOMUXC_I2C1_SDA__GPIO5_IO15 0x1e3
> + >;
> + };
> +
> + pinctrl_pmic: pmicirqgrp {
> + fsl,pins = <
> + MX8MP_IOMUXC_SAI1_TXD6__GPIO4_IO18 0x141
> + >;
> + };
> +
> + pinctrl_usdhc3: usdhc3grp {
> + fsl,pins = <
> + MX8MP_IOMUXC_NAND_WE_B__USDHC3_CLK 0x190
> + MX8MP_IOMUXC_NAND_WP_B__USDHC3_CMD 0x1d0
> + MX8MP_IOMUXC_NAND_DATA04__USDHC3_DATA0 0x1d0
> + MX8MP_IOMUXC_NAND_DATA05__USDHC3_DATA1 0x1d0
> + MX8MP_IOMUXC_NAND_DATA06__USDHC3_DATA2 0x1d0
> + MX8MP_IOMUXC_NAND_DATA07__USDHC3_DATA3 0x1d0
> + MX8MP_IOMUXC_NAND_RE_B__USDHC3_DATA4 0x1d0
> + MX8MP_IOMUXC_NAND_CE2_B__USDHC3_DATA5 0x1d0
> + MX8MP_IOMUXC_NAND_CE3_B__USDHC3_DATA6 0x1d0
> + MX8MP_IOMUXC_NAND_CLE__USDHC3_DATA7 0x1d0
> + MX8MP_IOMUXC_NAND_CE1_B__USDHC3_STROBE 0x190
> + >;
> + };
> +
> + pinctrl_usdhc3_100mhz: usdhc3-100mhzgrp {
> + fsl,pins = <
> + MX8MP_IOMUXC_NAND_WE_B__USDHC3_CLK 0x194
> + MX8MP_IOMUXC_NAND_WP_B__USDHC3_CMD 0x1d4
> + MX8MP_IOMUXC_NAND_DATA04__USDHC3_DATA0 0x1d4
> + MX8MP_IOMUXC_NAND_DATA05__USDHC3_DATA1 0x1d4
> + MX8MP_IOMUXC_NAND_DATA06__USDHC3_DATA2 0x1d4
> + MX8MP_IOMUXC_NAND_DATA07__USDHC3_DATA3 0x1d4
> + MX8MP_IOMUXC_NAND_RE_B__USDHC3_DATA4 0x1d4
> + MX8MP_IOMUXC_NAND_CE2_B__USDHC3_DATA5 0x1d4
> + MX8MP_IOMUXC_NAND_CE3_B__USDHC3_DATA6 0x1d4
> + MX8MP_IOMUXC_NAND_CLE__USDHC3_DATA7 0x1d4
> + MX8MP_IOMUXC_NAND_CE1_B__USDHC3_STROBE 0x194
> + >;
> + };
> +
> + pinctrl_usdhc3_200mhz: usdhc3-200mhzgrp {
> + fsl,pins = <
> + MX8MP_IOMUXC_NAND_WE_B__USDHC3_CLK 0x196
> + MX8MP_IOMUXC_NAND_WP_B__USDHC3_CMD 0x1d6
> + MX8MP_IOMUXC_NAND_DATA04__USDHC3_DATA0 0x1d6
> + MX8MP_IOMUXC_NAND_DATA05__USDHC3_DATA1 0x1d6
> + MX8MP_IOMUXC_NAND_DATA06__USDHC3_DATA2 0x1d6
> + MX8MP_IOMUXC_NAND_DATA07__USDHC3_DATA3 0x1d6
> + MX8MP_IOMUXC_NAND_RE_B__USDHC3_DATA4 0x1d6
> + MX8MP_IOMUXC_NAND_CE2_B__USDHC3_DATA5 0x1d6
> + MX8MP_IOMUXC_NAND_CE3_B__USDHC3_DATA6 0x1d6
> + MX8MP_IOMUXC_NAND_CLE__USDHC3_DATA7 0x1d6
> + MX8MP_IOMUXC_NAND_CE1_B__USDHC3_STROBE 0x196
> + >;
> + };
> +
> + pinctrl_wdog: wdoggrp {
> + fsl,pins = <
> + MX8MP_IOMUXC_GPIO1_IO02__WDOG1_WDOG_B 0xc6
> + >;
> + };
> +};
> --
> 2.7.4
>
