The 'marvell,pwm-offset' property of both GPIO blocks (per CP component)
point to the same counter registers offset. The driver will decide how
to use counters A/B.
This is different from the convention of pwm on earlier Armada series
(370/38x). On those systems the assignment of A/B counters to GPIO
blocks is coded in both DT and the driver. The actual behaviour of the
current driver on Armada 8K/7K is the same as earlier systems.
Add also clock properties for base pwm frequency reference.
Signed-off-by: Baruch Siach <baruch@xxxxxxxxxx>
---
arch/arm64/boot/dts/marvell/armada-ap80x.dtsi | 3 +++
arch/arm64/boot/dts/marvell/armada-cp11x.dtsi | 10 ++++++++++
2 files changed, 13 insertions(+)
diff --git a/arch/arm64/boot/dts/marvell/armada-ap80x.dtsi b/arch/arm64/boot/dts/marvell/armada-ap80x.dtsi
index 12e477f1aeb9..6614472100c2 100644
--- a/arch/arm64/boot/dts/marvell/armada-ap80x.dtsi
+++ b/arch/arm64/boot/dts/marvell/armada-ap80x.dtsi
@@ -281,6 +281,9 @@ ap_gpio: gpio@1040 {
gpio-controller;
#gpio-cells = <2>;
gpio-ranges = <&ap_pinctrl 0 0 20>;
+ marvell,pwm-offset = <0x10c0>;
+ #pwm-cells = <2>;
+ clocks = <&ap_clk 3>;
};
};
diff --git a/arch/arm64/boot/dts/marvell/armada-cp11x.dtsi b/arch/arm64/boot/dts/marvell/armada-cp11x.dtsi
index 994a2fce449a..d774a39334d9 100644
--- a/arch/arm64/boot/dts/marvell/armada-cp11x.dtsi
+++ b/arch/arm64/boot/dts/marvell/armada-cp11x.dtsi
@@ -234,12 +234,17 @@ CP11X_LABEL(gpio1): gpio@100 {
gpio-controller;
#gpio-cells = <2>;
gpio-ranges = <&CP11X_LABEL(pinctrl) 0 0 32>;
+ marvell,pwm-offset = <0x1f0>;
+ #pwm-cells = <2>;
interrupt-controller;
interrupts = <86 IRQ_TYPE_LEVEL_HIGH>,
<85 IRQ_TYPE_LEVEL_HIGH>,
<84 IRQ_TYPE_LEVEL_HIGH>,
<83 IRQ_TYPE_LEVEL_HIGH>;
#interrupt-cells = <2>;
+ clock-names = "core", "axi";
+ clocks = <&CP11X_LABEL(clk) 1 21>,
+ <&CP11X_LABEL(clk) 1 17>;
status = "disabled";
};
@@ -250,12 +255,17 @@ CP11X_LABEL(gpio2): gpio@140 {
gpio-controller;
#gpio-cells = <2>;
gpio-ranges = <&CP11X_LABEL(pinctrl) 0 32 31>;
+ marvell,pwm-offset = <0x1f0>;
+ #pwm-cells = <2>;
interrupt-controller;
interrupts = <82 IRQ_TYPE_LEVEL_HIGH>,
<81 IRQ_TYPE_LEVEL_HIGH>,
<80 IRQ_TYPE_LEVEL_HIGH>,
<79 IRQ_TYPE_LEVEL_HIGH>;
#interrupt-cells = <2>;
+ clock-names = "core", "axi";
+ clocks = <&CP11X_LABEL(clk) 1 21>,
+ <&CP11X_LABEL(clk) 1 17>;
status = "disabled";
};
};
--
2.29.2
