Hi, Qing,
On Sat, Dec 26, 2020 at 5:13 PM Qing Zhang <zhangqing@xxxxxxxxxxx> wrote:
>
> The SPI controller has the following characteristics:
>
> - Full-duplex synchronous serial data transmission
> - Support up to 4 variable length byte transmission
> - Main mode support
> - Mode failure generates an error flag and issues an interrupt request
> - Double buffer receiver
> - Serial clock with programmable polarity and phase
> - SPI can be controlled in wait mode
> - Support boot from SPI
>
> Use mtd_debug tool to earse/write/read /dev/mtd0 on development.
>
> eg:
>
> [root@linux mtd-utils-1.0.0]# mtd_debug erase /dev/mtd0 0x20000 0x40000
> Erased 262144 bytes from address 0x00020000 in flash
> [root@linux mtd-utils-1.0.0]# mtd_debug write /dev/mtd0 0x20000 13 1.img
> Copied 13 bytes from 1.img to address 0x00020000 in flash
> [root@linux mtd-utils-1.0.0]# mtd_debug read /dev/mtd0 0x20000 13 2.img
> Copied 13 bytes from address 0x00020000 in flash to 2.img
> [root@linux mtd-utils-1.0.0]# cmp -l 1.img 2.img
>
> Signed-off-by: Qing Zhang <zhangqing@xxxxxxxxxxx>
> ---
>
> v2:
> - keep Kconfig and Makefile sorted
> - make the entire comment a C++ one so things look more intentional
> - Fix unclear indentation
> - make conditional statements to improve legibility
> - Don't use static inline
> - the core handle message queue
> - Add a new binding document
> - Fix probe part mixed pdev and PCI
>
> v3:
> - expose set_cs to the core and let it handle things
> - replace transfer_one_message to transfer_one
> - replace spi_alloc_master to devm_spi_alloc_master
> - split out into prepare/unprepare_message
> - releases pci regions before unregister master
>
> v4:
> - names used in the manual
> - rename ls7a_spi_do_transfer to ls7a_spi_setup_transfer
> - change read the spcr and sper outside of this function
> - mode configuration moved to prepare instead
> - remove redundancy code about unprepare/prepare_message
> - used 0x4 instead of 0x1,WFEMPTY instead of RFEMPTY
>
> v5:
> - remove unnecessary blank lines
>
> ---
> drivers/spi/Kconfig | 7 ++
> drivers/spi/Makefile | 1 +
> drivers/spi/spi-ls7a.c | 280 +++++++++++++++++++++++++++++++++++++++++++++++++
> 3 files changed, 288 insertions(+)
> create mode 100644 drivers/spi/spi-ls7a.c
>
> diff --git a/drivers/spi/Kconfig b/drivers/spi/Kconfig
> index aadaea0..af7c0d4 100644
> --- a/drivers/spi/Kconfig
> +++ b/drivers/spi/Kconfig
> @@ -413,6 +413,13 @@ config SPI_LP8841_RTC
> Say N here unless you plan to run the kernel on an ICP DAS
> LP-8x4x industrial computer.
>
> +config SPI_LS7A
> + tristate "Loongson LS7A SPI Controller Support"
> + depends on CPU_LOONGSON64 || COMPILE_TEST
> + help
> + This drivers supports the Loongson LS7A SPI controller in master
> + SPI mode.
> +
> config SPI_MPC52xx
> tristate "Freescale MPC52xx SPI (non-PSC) controller support"
> depends on PPC_MPC52xx
> diff --git a/drivers/spi/Makefile b/drivers/spi/Makefile
> index 6fea582..d015cf2 100644
> --- a/drivers/spi/Makefile
> +++ b/drivers/spi/Makefile
> @@ -61,6 +61,7 @@ obj-$(CONFIG_SPI_LANTIQ_SSC) += spi-lantiq-ssc.o
> obj-$(CONFIG_SPI_JCORE) += spi-jcore.o
> obj-$(CONFIG_SPI_LM70_LLP) += spi-lm70llp.o
> obj-$(CONFIG_SPI_LP8841_RTC) += spi-lp8841-rtc.o
> +obj-$(CONFIG_SPI_LS7A) += spi-ls7a.o
> obj-$(CONFIG_SPI_MESON_SPICC) += spi-meson-spicc.o
> obj-$(CONFIG_SPI_MESON_SPIFC) += spi-meson-spifc.o
> obj-$(CONFIG_SPI_MPC512x_PSC) += spi-mpc512x-psc.o
> diff --git a/drivers/spi/spi-ls7a.c b/drivers/spi/spi-ls7a.c
> new file mode 100644
> index 0000000..d24b6d91
> --- /dev/null
> +++ b/drivers/spi/spi-ls7a.c
> @@ -0,0 +1,280 @@
> +// SPDX-License-Identifier: GPL-2.0-only
> +//
> +// Loongson LS7A SPI Controller driver
> +//
> +// Copyright (C) 2020 Loongson Technology Corporation Limited.
> +//
> +
> +#include <linux/module.h>
> +#include <linux/pci.h>
> +#include <linux/spi/spi.h>
> +
> +/* define spi register */
> +#define SPCR 0x00
> +#define SPSR 0x01
> +#define FIFO 0x02
> +#define SPER 0x03
> +#define SFC_PARAM 0x04
> +#define SFC_SOFTCS 0x05
> +#define SFC_TIMING 0x06
> +
> +struct ls7a_spi {
> + struct spi_master *master;
> + void __iomem *base;
> + unsigned int hz;
> + unsigned int mode;
> +};
> +
> +static void ls7a_spi_write_reg(struct ls7a_spi *spi,
> + unsigned char reg,
> + unsigned char data)
> +{
> + writeb(data, spi->base + reg);
> +}
> +
> +static char ls7a_spi_read_reg(struct ls7a_spi *spi, unsigned char reg)
> +{
> + return readb(spi->base + reg);
> +}
> +
> +static int ls7a_spi_prepare_message(struct spi_master *master,
> + struct spi_message *msg)
> +{
> + struct ls7a_spi *ls7a_spi;
> + struct spi_device *spi = msg->spi;
> + unsigned char val;
> +
> + ls7a_spi = spi_master_get_devdata(master);
> +
> + if (ls7a_spi->mode != spi->mode) {
> + val = ls7a_spi_read_reg(ls7a_spi, SPCR);
> + val &= ~0xc;
> + if (spi->mode & SPI_CPOL)
> + val |= 8;
> + if (spi->mode & SPI_CPHA)
> + val |= 4;
> + ls7a_spi_write_reg(ls7a_spi, SPCR, val);
> + val = ls7a_spi_read_reg(ls7a_spi, SPER);
> + ls7a_spi_write_reg(ls7a_spi, SPER, val);
> + ls7a_spi->mode = spi->mode;
> + }
> + return 0;
I'm sorry that I hadn't review very carefully in V4 and you need to
send another new version. In kernel code we usually keep a blank line
before the last "return xxx" in a function, and there are several
other places with the same problem.
Huacai
> +}
> +
> +static void ls7a_spi_set_cs(struct spi_device *spi, bool enable)
> +{
> + struct ls7a_spi *ls7a_spi;
> + int cs;
> +
> + ls7a_spi = spi_master_get_devdata(spi->master);
> +
> + cs = ls7a_spi_read_reg(ls7a_spi, SFC_SOFTCS) & ~(0x11 << spi->chip_select);
> +
> + if (!!(spi->mode & SPI_CS_HIGH) == enable)
> + ls7a_spi_write_reg(ls7a_spi, SFC_SOFTCS, (0x1 << spi->chip_select) | cs);
> + else
> + ls7a_spi_write_reg(ls7a_spi, SFC_SOFTCS, (0x11 << spi->chip_select) | cs);
> +}
> +
> +static int ls7a_spi_setup_transfer(struct spi_device *spi,
> + struct spi_transfer *t)
> +{
> + unsigned int hz;
> + unsigned int div, div_tmp;
> + unsigned int bit;
> + unsigned long clk;
> + unsigned char val;
> + unsigned char spcr, sper;
> + const char rdiv[12] = {0, 1, 4, 2, 3, 5, 6, 7, 8, 9, 10, 11};
> + struct ls7a_spi *ls7a_spi;
> +
> + ls7a_spi = spi_master_get_devdata(spi->master);
> +
> + if (t) {
> + hz = t->speed_hz;
> + if (!hz)
> + hz = spi->max_speed_hz;
> + } else {
> + hz = spi->max_speed_hz;
> + }
> +
> + if (hz & (ls7a_spi->hz != hz)) {
> + clk = 100000000;
> +
> + div = DIV_ROUND_UP(clk, hz);
> + if (div < 2)
> + div = 2;
> + if (div > 4096)
> + div = 4096;
> +
> + bit = fls(div) - 1;
> + if ((1 << bit) == div)
> + bit--;
> + div_tmp = rdiv[bit];
> +
> + dev_dbg(&spi->dev, "clk = %ld hz = %d div_tmp = %d bit = %d\n",
> + clk, hz, div_tmp, bit);
> +
> + ls7a_spi->hz = hz;
> + spcr = div_tmp & 3;
> + sper = (div_tmp >> 2) & 3;
> +
> + val = ls7a_spi_read_reg(ls7a_spi, SPCR);
> + ls7a_spi_write_reg(ls7a_spi, SPCR, (val & ~3) | spcr);
> + val = ls7a_spi_read_reg(ls7a_spi, SPER);
> + ls7a_spi_write_reg(ls7a_spi, SPER, (val & ~3) | sper);
> + }
> + return 0;
> +}
> +
> +static int ls7a_spi_setup(struct spi_device *spi)
> +{
> + return ls7a_spi_setup_transfer(spi, NULL);
> +}
> +
> +static int ls7a_spi_write_read_8bit(struct spi_device *spi,
> + const u8 **tx_buf, u8 **rx_buf,
> + unsigned int num)
> +{
> + struct ls7a_spi *ls7a_spi;
> +
> + ls7a_spi = spi_master_get_devdata(spi->master);
> +
> + if (tx_buf && *tx_buf) {
> + ls7a_spi_write_reg(ls7a_spi, FIFO, *((*tx_buf)++));
> +
> + while ((ls7a_spi_read_reg(ls7a_spi, SPSR) & 0x4) == 1)
> + ;
> + } else {
> + ls7a_spi_write_reg(ls7a_spi, FIFO, 0);
> +
> + while ((ls7a_spi_read_reg(ls7a_spi, SPSR) & 0x1) == 1)
> + ;
> + }
> +
> + if (rx_buf && *rx_buf)
> + *(*rx_buf)++ = ls7a_spi_read_reg(ls7a_spi, FIFO);
> + else
> + ls7a_spi_read_reg(ls7a_spi, FIFO);
> +
> + return 1;
> +}
> +
> +static unsigned int ls7a_spi_write_read(struct spi_device *spi,
> + struct spi_transfer *xfer)
> +{
> + unsigned int count;
> + const u8 *tx = xfer->tx_buf;
> + u8 *rx = xfer->rx_buf;
> +
> + count = xfer->len;
> +
> + do {
> + if (ls7a_spi_write_read_8bit(spi, &tx, &rx, count) < 0)
> + goto out;
> + count--;
> + } while (count);
> +
> +out:
> + return xfer->len - count;
> +}
> +
> +static int ls7a_spi_transfer_one(struct spi_master *master,
> + struct spi_device *spi,
> + struct spi_transfer *t)
> +{
> + int status = 0;
> +
> + status = ls7a_spi_setup_transfer(spi, t);
> + if (status < 0)
> + return status;
> +
> + if (t->len)
> + ls7a_spi_write_read(spi, t);
> +
> + return status;
> +}
> +
> +static int ls7a_spi_pci_probe(struct pci_dev *pdev,
> + const struct pci_device_id *ent)
> +{
> + struct spi_master *master;
> + struct ls7a_spi *spi;
> + int ret;
> +
> + master = devm_spi_alloc_master(&pdev->dev, sizeof(*spi));
> + if (!master)
> + return -ENOMEM;
> +
> + spi = spi_master_get_devdata(master);
> + ret = pcim_enable_device(pdev);
> + if (ret)
> + goto err_free_master;
> +
> + ret = pci_request_regions(pdev, "ls7a-spi");
> + if (ret)
> + goto err_free_master;
> +
> + spi->base = pcim_iomap(pdev, 0, pci_resource_len(pdev, 0));
> + if (!spi->base) {
> + ret = -EINVAL;
> + goto err_free_master;
> + }
> + ls7a_spi_write_reg(spi, SPCR, 0x51);
> + ls7a_spi_write_reg(spi, SPER, 0x00);
> + ls7a_spi_write_reg(spi, SFC_TIMING, 0x01);
> + ls7a_spi_write_reg(spi, SFC_PARAM, 0x40);
> + spi->mode = 0;
> +
> + master->mode_bits = SPI_CPOL | SPI_CPHA | SPI_CS_HIGH;
> + master->set_cs = ls7a_spi_set_cs;
> + master->prepare_message = ls7a_spi_prepare_message;
> + master->setup = ls7a_spi_setup;
> + master->transfer_one = ls7a_spi_transfer_one;
> + master->bits_per_word_mask = SPI_BPW_MASK(8);
> + master->num_chipselect = 4;
> + master->dev.of_node = pdev->dev.of_node;
> +
> + spi->master = master;
> +
> + pci_set_drvdata(pdev, master);
> +
> + ret = spi_register_master(master);
> + if (ret)
> + goto err_free_master;
> +
> + return 0;
> +
> +err_free_master:
> + pci_release_regions(pdev);
> + return ret;
> +}
> +
> +static void ls7a_spi_pci_remove(struct pci_dev *pdev)
> +{
> + struct spi_master *master = pci_get_drvdata(pdev);
> +
> + spi_unregister_master(master);
> + pci_release_regions(pdev);
> +}
> +
> +static const struct pci_device_id ls7a_spi_pci_id_table[] = {
> + { PCI_DEVICE(PCI_VENDOR_ID_LOONGSON, 0x7a0b) },
> + { 0, }
> +};
> +
> +MODULE_DEVICE_TABLE(pci, ls7a_spi_pci_id_table);
> +
> +static struct pci_driver ls7a_spi_pci_driver = {
> + .name = "ls7a-spi",
> + .id_table = ls7a_spi_pci_id_table,
> + .probe = ls7a_spi_pci_probe,
> + .remove = ls7a_spi_pci_remove,
> +};
> +
> +module_pci_driver(ls7a_spi_pci_driver);
> +
> +MODULE_AUTHOR("Juxin Gao <gaojuxin@xxxxxxxxxxx>");
> +MODULE_AUTHOR("Qing Zhang <zhangqing@xxxxxxxxxxx>");
> +MODULE_DESCRIPTION("Loongson LS7A SPI controller driver");
> +MODULE_LICENSE("GPL v2");
> --
> 2.1.0
>
