On 12/22/20 11:45 AM, Mimi Zohar wrote:
On Tue, 2020-12-22 at 10:53 -0800, Lakshmi Ramasubramanian wrote:
On 12/22/20 6:26 AM, Mimi Zohar wrote:
Hi Mimi,
On Sat, 2020-12-19 at 09:57 -0800, Lakshmi Ramasubramanian wrote:
diff --git a/arch/powerpc/kexec/Makefile b/arch/powerpc/kexec/Makefile
index 4aff6846c772..b6c52608cb49 100644
--- a/arch/powerpc/kexec/Makefile
+++ b/arch/powerpc/kexec/Makefile
@@ -9,13 +9,6 @@ obj-$(CONFIG_PPC32) += relocate_32.o
obj-$(CONFIG_KEXEC_FILE) += file_load.o ranges.o file_load_$(BITS).o elf_$(BITS).o
-ifdef CONFIG_HAVE_IMA_KEXEC
-ifdef CONFIG_IMA
-obj-y += ima.o
-endif
-endif
Notice how "kexec/ima.o" is only included if the architecture supports
it and IMA is configured. In addition only if CONFIG_IMA_KEXEC is
configured, is the IMA measurement list carried across kexec. After
moving the rest of ima.c to drivers/of/kexec.c, this changes. Notice
how drivers/of/Kconfig includes kexec.o:
obj-$(CONFIG_KEXEC_FILE) += kexec.o
It is not dependent on CONFIG_HAVE_IMA_KEXEC. Shouldn't all of the
functions defined in ima.c being moved to kexec.o be defined within a
CONFIG_HAVE_IMA_KEXEC ifdef?
Thanks for reviewing the changes.
In "drivers/of/kexec.c" the function remove_ima_buffer() is defined
under "#ifdef CONFIG_HAVE_IMA_KEXEC"
setup_ima_buffer() is defined under "#ifdef CONFIG_IMA_KEXEC" - the same
way it was defined in "arch/powerpc/kexec/ima.c".
As you know, CONFIG_IMA_KEXEC depends on CONFIG_HAVE_IMA_KEXEC (as
defined in "security/integrity/ima/Kconfig").
ima_get_kexec_buffer() and ima_free_kexec_buffer() are unconditionally
defined in "drivers/of/kexec.c" even though they are called only when
CONFIG_HAVE_IMA_KEXEC is enabled. I will update these two functions to
be moved under "#ifdef CONFIG_HAVE_IMA_KEXEC"
The issue is the reverse. CONFIG_HAVE_IMA_KEXEC may be enabled without
CONFIG_IMA_KEXEC being enabled. This allows the architecture to
support carrying the measurement list across kexec, but requires
enabling it at build time.
Only if CONFIG_HAVE_IMA_KEXEC is enabled should any of these functions
be compiled at build. This allows restoring the previous IMA
measurement list, even if CONFIG_IMA_KEXEC is not enabled.
Only if CONFIG_IMA_KEXEC is enabled, should carrying the measurement
list across kexec be enabled. See how arch_ima_add_kexec_buffer,
write_number, setup_ima_buffer are ifdef'ed in
arch/powerpc/kexec/ima.c.
Yes - I agree. I will make the following changes:
=> Enable the functions moved from "arch/powerpc/kexec/ima.c" to
"drivers/of/kexec.c" only when CONFIG_HAVE_IMA_KEXEC is enabled.
=> Also, compile write_number() and setup_ima_buffer() only when
CONFIG_IMA_KEXEC is enabled.
thanks,
-lakshmi
