Hi Adam,
On Tue, Dec 22, 2020 at 2:39 AM Adam Ford <aford173@xxxxxxxxx> wrote:
> On Fri, Dec 18, 2020 at 7:16 AM Geert Uytterhoeven <geert@xxxxxxxxxxxxxx> wrote:
> > On Thu, Dec 17, 2020 at 12:52 PM Adam Ford <aford173@xxxxxxxxx> wrote:
> > > On Thu, Dec 17, 2020 at 2:16 AM Geert Uytterhoeven <geert@xxxxxxxxxxxxxx> wrote:
> > > > On Wed, Dec 16, 2020 at 6:03 PM Adam Ford <aford173@xxxxxxxxx> wrote:
> > > > > On Wed, Dec 16, 2020 at 8:55 AM Geert Uytterhoeven <geert@xxxxxxxxxxxxxx> wrote:
> > > > > > On Sun, Dec 13, 2020 at 7:38 PM Adam Ford <aford173@xxxxxxxxx> wrote:
> > > > > > > When the board was added, clock drivers were being updated done at
> > > > > > > the same time to allow the versaclock driver to properly configure
> > > > > > > the modes. Unforutnately, the updates were not applied to the board
> > > >
> > > > > > > --- a/arch/arm64/boot/dts/renesas/beacon-renesom-baseboard.dtsi
> > > > > > > +++ b/arch/arm64/boot/dts/renesas/beacon-renesom-baseboard.dtsi
> > > > > > > @@ -5,6 +5,7 @@
> > > > > > >
> > > > > > > #include <dt-bindings/gpio/gpio.h>
> > > > > > > #include <dt-bindings/input/input.h>
> > > > > > > +#include <dt-bindings/clk/versaclock.h>
> > > > > > >
> > > > > > > / {
> > > > > > > backlight_lvds: backlight-lvds {
> > > > > > > @@ -294,12 +295,12 @@ &du_out_rgb {
> > > > > > > &ehci0 {
> > > > > > > dr_mode = "otg";
> > > > > > > status = "okay";
> > > > > > > - clocks = <&cpg CPG_MOD 703>, <&cpg CPG_MOD 704>;
> > > > > > > + clocks = <&cpg CPG_MOD 703>, <&cpg CPG_MOD 704>, <&versaclock5 3>;
> > > > > >
> > > > > > Why this change? You said before you don't need this
> > > > > > https://lore.kernel.org/linux-renesas-soc/CAHCN7xJWbP16SA-Ok-5syNnqOZAt8OFJo2_rtg5VrNVsN2-eiQ@xxxxxxxxxxxxxx/
> > > > > >
> > > > >
> > > > > I had talked with the hardware guys about buy pre-programmed
> > > > > versaclock chips which would have been pre-configured and pre-enabled.
> > > > > I thought it was going to happen, but it didn't, so we need the
> > > > > versaclock driver to enable the reference clock for the USB
> > > > > controllers, ethernet controller and audio clocks. Previously we were
> > > > > manually configuring it or it was coincidentally working. Ideally,
> > > > > we'd have the clock system intentionally enable/disable the clocks
> > > > > when drivers are loaded/unloaded for for power management reasons.
> > > >
> > > > Can you tell me how exactly the Versaclock outputs are wired?
> > >
> > > The SoC is expecting a fixed external 50 MHz clock connected to
> > > USB_EXTAL. Instead of a fixed clock, we're using the Versaclock.
> > > We're also using the Versaclock to drive the AVB TXCRefClk,
> > > du_dotclkiun0 and du_dotclkin2 (also also called du_dotclkin3 on
> > > RZ/G2N) instead of fixed clocks.
> > >
> > > > E.g. for USB, the bindings don't say anything about a third clock input,
> > > > so I'd like to know where that clock is fed into USB.
> > >
> > > The way the driver is crafted, it can take in multiple clocks and it
> > > goes through a list to enable them all, so I added the versaclock to
> > > the array. Without the versaclock reference, the clock doesn't get
> > > turned on and the USB fails to operate.
> >
> > According to the Hardware User's Manual, USBL_EXTAL is used for USB3.0,
> > while you added the clock references to the EHCI nodes.
> > Are you sure EHCI is failing without this?
> >
> > Still, it means we need to extend the bindings/driver for
> > renesas,rcar-gen3-xhci to handle USB_EXTAL.
>
> After investigating this, it looks like the USB_EXTAL is already
> referenced from the device tree and it's referenced by the USB3 Phy.
> The SoC calls it usb_extal_clk. Since the phy driver is calling
> devm_clk_get() it looks like i could just redefine the clocks of
> usb3_phy0 to point to the versaclock instead of usb_extal_clk.
>
> The other option is to use a similar method I proposed for the audio
> reference clock and redefine the usb_extal_clk as a fixed
> fixed-factor-clock.
>
> Do you have a preference as to which direction I go?
I'd go for the classical solution: override the clocks property of the
usb3_phy0 node.
Thanks!
Gr{oetje,eeting}s,
Geert
--
Geert Uytterhoeven -- There's lots of Linux beyond ia32 -- geert@xxxxxxxxxxxxxx
In personal conversations with technical people, I call myself a hacker. But
when I'm talking to journalists I just say "programmer" or something like that.
-- Linus Torvalds
