Re: [PATCH v2 47/48] ARM: tegra: ventana: Support CPU voltage scaling and thermal throttling

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



On 17/12/2020 19:06, Dmitry Osipenko wrote:
> Enable CPU voltage scaling and thermal throttling on Tegra20 Ventana board.
> 
> Signed-off-by: Dmitry Osipenko <digetx@xxxxxxxxx>
> ---
>  arch/arm/boot/dts/tegra20-ventana.dts | 40 ++++++++++++++++++++++++++-
>  1 file changed, 39 insertions(+), 1 deletion(-)
> 
> diff --git a/arch/arm/boot/dts/tegra20-ventana.dts b/arch/arm/boot/dts/tegra20-ventana.dts
> index 14ace2ef749c..c2d9f38960bc 100644
> --- a/arch/arm/boot/dts/tegra20-ventana.dts
> +++ b/arch/arm/boot/dts/tegra20-ventana.dts
> @@ -2,8 +2,10 @@
>  /dts-v1/;
>  
>  #include <dt-bindings/input/input.h>
> +#include <dt-bindings/thermal/thermal.h>
>  #include "tegra20.dtsi"
>  #include "tegra20-cpu-opp.dtsi"
> +#include "tegra20-cpu-opp-microvolt.dtsi"
>  
>  / {
>  	model = "NVIDIA Tegra20 Ventana evaluation board";
> @@ -527,9 +529,10 @@ ldo_rtc {
>  			};
>  		};
>  
> -		temperature-sensor@4c {
> +		nct1008: temperature-sensor@4c {
>  			compatible = "onnn,nct1008";
>  			reg = <0x4c>;
> +			#thermal-sensor-cells = <1>;
>  		};
>  	};
>  
> @@ -615,10 +618,13 @@ clk32k_in: clock@0 {
>  
>  	cpus {
>  		cpu0: cpu@0 {
> +			cpu-supply = <&vdd_cpu>;
>  			operating-points-v2 = <&cpu0_opp_table>;
> +			#cooling-cells = <2>;
>  		};
>  
>  		cpu@1 {
> +			cpu-supply = <&vdd_cpu>;
>  			operating-points-v2 = <&cpu0_opp_table>;
>  		};
>  	};
> @@ -717,4 +723,36 @@ sound {
>  			 <&tegra_car TEGRA20_CLK_CDEV1>;
>  		clock-names = "pll_a", "pll_a_out0", "mclk";
>  	};
> +
> +	thermal-zones {
> +		cpu-thermal {
> +			polling-delay-passive = <1000>; /* milliseconds */
> +			polling-delay = <5000>; /* milliseconds */
> +
> +			thermal-sensors = <&nct1008 1>;
> +
> +			trips {
> +				trip0: cpu-alert0 {
> +					/* start throttling at 50C */
> +					temperature = <50000>;
> +					hysteresis = <200>;

Did you mean <2000> ?

> +					type = "passive";
> +				};
> +
> +				trip1: cpu-crit {
> +					/* shut down at 60C */
> +					temperature = <60000>;
> +					hysteresis = <2000>;

I think you can drop the hysteresis here, when the critical temperature
is reached, there is an emergency shutdown.

50°C and 60°C sound very low values, no ?

> +					type = "critical";
> +				};
> +			};
> +
> +			cooling-maps {
> +				map0 {
> +					trip = <&trip0>;
> +					cooling-device = <&cpu0 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>;

You should add all CPUs here.

> +				};
> +			};
> +		};
> +	};
>  };
> 


-- 
<http://www.linaro.org/> Linaro.org │ Open source software for ARM SoCs

Follow Linaro:  <http://www.facebook.com/pages/Linaro> Facebook |
<http://twitter.com/#!/linaroorg> Twitter |
<http://www.linaro.org/linaro-blog/> Blog



[Index of Archives]     [Device Tree Compilter]     [Device Tree Spec]     [Linux Driver Backports]     [Video for Linux]     [Linux USB Devel]     [Linux PCI Devel]     [Linux Audio Users]     [Linux Kernel]     [Linux SCSI]     [XFree86]     [Yosemite Backpacking]


  Powered by Linux