On Thu, Dec 17, 2020 at 05:21:32PM +0800, Peng.Zhou wrote:
>
> On Wed, 2020-11-25 at 17:03 +0800, Stanley Chu wrote:
> > Hi Eric,
> >
> > On Mon, 2020-11-23 at 18:01 -0800, Eric Biggers wrote:
> > > Hi Adrian,
> > >
> > > On Mon, Nov 23, 2020 at 09:04:12AM +0200, Adrian Hunter wrote:
> > > > On 20/11/20 9:44 pm, Eric Biggers wrote:
> > > > > Hi Adrian,
> > > > >
> > > > > On Fri, Nov 20, 2020 at 09:29:59PM +0200, Adrian Hunter wrote:
> > > > >> I haven't had a chance to look at it properly, but I do have a couple of
> > > > >> dumb questions. How do you ensure the host controller is not runtime
> > > > >> suspended when the key is programmed?
> > > > >
> > > > > This is handled by the block layer, in block/keyslot-manager.c. It ensures that
> > > > > the device is resumed before calling blk_ksm_ll_ops::keyslot_program() or
> > > > > blk_ksm_ll_ops::keyslot_evict(). See blk_ksm_hw_enter().
> > > >
> > > > Cool, although cqhci is doing a lazy kind of resume, so maybe not be enabled
> > > > when a key is programmed? Would that be a problem?
> > > >
> > > > >
> > > > >> Are the keys lost when the host controller is reset, and then how do you know
> > > > >> the host controller does not get reset after the key is programmed but before
> > > > >> the I/O is submitted?
> > > > >
> > > > > As with UFS, keys might be lost when the host controller is reset, so we're
> > > > > reprogramming all the keys when that happens. See patch 1:
> > > > >
> > > > > mmc_set_initial_state()
> > > > > mmc_crypto_set_initial_state()
> > > > > blk_ksm_reprogram_all_keys()
> > > > >
> > > > > (That's the intent, at least. For MMC, I'm not sure if resets were properly
> > > > > covered by the testing I've done so far. But the code looks right to me.)
> > > >
> > > > After reset, cqhci will not necessarily be enabled at this point. Is that OK?
> > >
> > > The hardware that I have (sdm630) appears to allow programming and evicting keys
> > > even while CQHCI_CFG.CQHCI_ENABLE is clear, i.e. even when the CQE is "off".
> > > I tested it using the patch below.
> > >
> > > The eMMC specification isn't clear about this point. But I'm thinking that the
> > > crypto configuration registers (the keyslots) are probably supposed to work like
> > > most of the other CQHCI registers, which can be written to while CQHCI_ENABLE is
> > > clear. Then setting CQHCI_ENABLE just enables the ability to actually issue
> > > requests. Likewise, setting CQHCI_CRYPTO_GENERAL_ENABLE just allows using
> > > crypto in requests; it isn't needed to write to the crypto configurations.
> > >
> > > For what it's worth, UFS crypto (which has been supported by upstream since
> > > v5.9) works similarly. Keys can be programmed while the UFS host is powered on,
> > > even before it's "enabled".
> > >
> > > But maybe someone interpreted the eMMC specification differently. Hopefully
> > > Mediatek can give some insight into how they implemented it, and test this
> > > patchset on their hardware too.
> >
> > MediaTek CQHCI also works in this way.
> >
> > Complete test is on-going now and we will update the results as soon as
> > possible.
> >
> > Thanks,
> > Stanley Chu
> >
> > >
> > > Here's the patch I used to verify that sdm630 allows programming and evicting
> > > keys even while the CQE is off:
> > >
> > > diff --git a/drivers/mmc/core/block.c b/drivers/mmc/core/block.c
> > > index eaf2f1074326..eb2d88d0b3ba 100644
> > > --- a/drivers/mmc/core/block.c
> > > +++ b/drivers/mmc/core/block.c
> > > @@ -1406,6 +1406,9 @@ static void mmc_blk_cqe_complete_rq(struct mmc_queue *mq, struct request *req)
> > >
> > > mmc_cqe_check_busy(mq);
> > >
> > > + if (mmc_tot_in_flight(mq) == 0 && host->cqe_on)
> > > + host->cqe_ops->cqe_off(host);
> > > +
> > > spin_unlock_irqrestore(&mq->lock, flags);
> > >
> > > if (!mq->cqe_busy)
> > > diff --git a/drivers/mmc/host/sdhci-msm.c b/drivers/mmc/host/sdhci-msm.c
> > > index 6ce21414d510..70d8dbc6515f 100644
> > > --- a/drivers/mmc/host/sdhci-msm.c
> > > +++ b/drivers/mmc/host/sdhci-msm.c
> > > @@ -1971,6 +1971,12 @@ static int sdhci_msm_program_key(struct cqhci_host *cq_host,
> > > int i;
> > > int err;
> > >
> > > + if (!cq_host->mmc->cqe_on) {
> > > + pr_info("@@@ cqe is off for %s slot %d\n",
> > > + (cfg->config_enable & CQHCI_CRYPTO_CONFIGURATION_ENABLE) ?
> > > + "program" : "evict", slot);
> > > + }
> > > +
> > > if (!(cfg->config_enable & CQHCI_CRYPTO_CONFIGURATION_ENABLE))
> > > return qcom_scm_ice_invalidate_key(slot);
> >
> >
>
> Hi Eric,
>
> I also have a question about reprogramming keys scenarios, if some SoC
> vensors' eMMC host will power down or something else like that keys will
> be lost after runtime suspend, that means we must do reprogramming keys
> in runtime resume, right? Do you think that we should add it in
> cqhci-core layer(such as __cqhci_enable()) or every SoC vendor's host
> driver resume path?
>
The keys should only be lost on reset, not on runtime suspend. So I believe the
code I've proposed is sufficient.
- Eric
