Re: [PATCH v3 4/4] arm64: dts: freescale: Add support for phyBOARD-Pollux-i.MX8MP

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



Hello Teresa,

I'm sorry if I was too brief in my review last time, see below.

Am Freitag, 11. Dezember 2020, 14:48:55 CET schrieb Teresa Remmet:
> Add initial support for phyBOARD-Pollux-i.MX8MP.
> Supported basic features:
> 	* eMMC
> 	* i2c EEPROM
> 	* i2c RTC
> 	* i2c LED
> 	* PMIC
> 	* debug UART
> 	* SD card
> 	* 1Gbit Ethernet (fec)
> 	* watchdog
> 
> Signed-off-by: Teresa Remmet <t.remmet@xxxxxxxxx>
> Reviewed-by: Krzysztof Kozlowski <krzk@xxxxxxxxxx>
> ---
>  arch/arm64/boot/dts/freescale/Makefile             |   1 +
>  .../dts/freescale/imx8mp-phyboard-pollux-rdk.dts   | 163 ++++++++++++
>  .../boot/dts/freescale/imx8mp-phycore-som.dtsi     | 296
> +++++++++++++++++++++ 3 files changed, 460 insertions(+)
>  create mode 100644
> arch/arm64/boot/dts/freescale/imx8mp-phyboard-pollux-rdk.dts create mode
> 100644 arch/arm64/boot/dts/freescale/imx8mp-phycore-som.dtsi
> 
> diff --git a/arch/arm64/boot/dts/freescale/Makefile
> b/arch/arm64/boot/dts/freescale/Makefile index acfb8af45912..a43b496678be
> 100644
> --- a/arch/arm64/boot/dts/freescale/Makefile
> +++ b/arch/arm64/boot/dts/freescale/Makefile
> @@ -37,6 +37,7 @@ dtb-$(CONFIG_ARCH_MXC) += imx8mn-evk.dtb
>  dtb-$(CONFIG_ARCH_MXC) += imx8mn-ddr4-evk.dtb
>  dtb-$(CONFIG_ARCH_MXC) += imx8mn-var-som-symphony.dtb
>  dtb-$(CONFIG_ARCH_MXC) += imx8mp-evk.dtb
> +dtb-$(CONFIG_ARCH_MXC) += imx8mp-phyboard-pollux-rdk.dtb
>  dtb-$(CONFIG_ARCH_MXC) += imx8mq-evk.dtb
>  dtb-$(CONFIG_ARCH_MXC) += imx8mq-hummingboard-pulse.dtb
>  dtb-$(CONFIG_ARCH_MXC) += imx8mq-librem5-devkit.dtb
> diff --git a/arch/arm64/boot/dts/freescale/imx8mp-phyboard-pollux-rdk.dts
> b/arch/arm64/boot/dts/freescale/imx8mp-phyboard-pollux-rdk.dts new file
> mode 100644
> index 000000000000..e92868c10526
> --- /dev/null
> +++ b/arch/arm64/boot/dts/freescale/imx8mp-phyboard-pollux-rdk.dts
> @@ -0,0 +1,163 @@
> +// SPDX-License-Identifier: GPL-2.0
> +/*
> + * Copyright (C) 2020 PHYTEC Messtechnik GmbH
> + * Author: Teresa Remmet <t.remmet@xxxxxxxxx>
> + */
> +
> +/dts-v1/;
> +
> +#include <dt-bindings/leds/leds-pca9532.h>
> +#include <dt-bindings/pwm/pwm.h>
> +#include "imx8mp-phycore-som.dtsi"
> +
> +/ {
> +	model = "PHYTEC phyBOARD-Pollux i.MX8MP";
> +	compatible = "phytec,imx8mp-phyboard-pollux-rdk",
> +		     "phytec,imx8mp-phycore-som", "fsl,imx8mp";
> +
> +	chosen {
> +		stdout-path = &uart2;
> +	};
> +
> +	reg_usdhc2_vmmc: regulator-usdhc2 {
> +		compatible = "regulator-fixed";
> +		pinctrl-names = "default";
> +		pinctrl-0 = <&pinctrl_reg_usdhc2_vmmc>;
> +		regulator-name = "VSD_3V3";
> +		regulator-min-microvolt = <3300000>;
> +		regulator-max-microvolt = <3300000>;
> +		gpio = <&gpio2 19 GPIO_ACTIVE_HIGH>;
> +		enable-active-high;
> +		startup-delay-us = <100>;
> +		off-on-delay-us = <12000>;
> +	};
> +};
> +
> +&i2c2 {
> +	clock-frequency = <400000>;
> +	pinctrl-names = "default";
> +	pinctrl-0 = <&pinctrl_i2c2>;
> +	pinctrl-1 = <&pinctrl_i2c2_gpio>;
> +	sda-gpios = <&gpio5 17 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
> +	scl-gpios = <&gpio5 16 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
> +	status = "okay";
> +
> +	eeprom@51 {
> +		compatible = "atmel,24c02";
> +		reg = <0x51>;
> +		pagesize = <16>;
> +		status = "okay";
> +	};
> +
> +	leds@62 {
> +		compatible = "nxp,pca9533";
> +		reg = <0x62>;
> +		status = "okay";
> +
> +		led1 {
> +			type = <PCA9532_TYPE_LED>;
> +		};
> +
> +		led2 {
> +			type = <PCA9532_TYPE_LED>;
> +		};
> +
> +		led3 {
> +			type = <PCA9532_TYPE_LED>;
> +		};
> +	};

You just removed the "label" property. Now the label is generated 
automatically (which is the preferred way), but you did neither add the 
property "color" nor "function", so the label will be constructed from the 
node name only.

Well I just saw the binding for that LED controller is not converted to yaml 
yet … Documentation/devicetree/bindings/leds/leds-pca9532.txt

Anyways, the modern approach would look like somehow like this:

                led-0 {
                        function = LED_FUNCTION_ALARM;
                        color = <LED_COLOR_ID_RED>;
                };

                led-1 {
                        function = LED_FUNCTION_STATUS;
                        color = <LED_COLOR_ID_GREEN>;
                };

                led-2 {
                        function = LED_FUNCTION_INDICATOR;
                        color = <LED_COLOR_ID_RED>;
                        function-enumerator = <1>;
                };

                led-3 {
                        function = LED_FUNCTION_INDICATOR;
                        color = <LED_COLOR_ID_RED>;
                        function-enumerator = <2>;
                };

Hope that helps, for more see Documentation/devicetree/bindings/leds and 
especially the bindings already converted to yaml. The available macros are in 
include/dt-bindings/leds/common.h 

Maybe just add the colors for now, if you're not sure what the function should 
be. As far as I could see the driver for that LED controller does not yet 
support multicolor, but I added linux-leds to Cc, maybe someone over there 
knows more?

Sorry to nag about this, but I think it's better to not introduce new dts 
files with deprecated properties. If that kind of feedback is not desired, 
please let me know.

Greets
Alex

> +};
> +
> +&snvs_pwrkey {
> +	status = "okay";
> +};
> +
> +/* debug console */
> +&uart2 {
> +	pinctrl-names = "default";
> +	pinctrl-0 = <&pinctrl_uart2>;
> +	status = "okay";
> +};
> +
> +/* SD-Card */
> +&usdhc2 {
> +	pinctrl-names = "default", "state_100mhz", "state_200mhz";
> +	pinctrl-0 = <&pinctrl_usdhc2>, <&pinctrl_usdhc2_pins>;
> +	pinctrl-1 = <&pinctrl_usdhc2_100mhz>, <&pinctrl_usdhc2_pins>;
> +	pinctrl-2 = <&pinctrl_usdhc2_200mhz>, <&pinctrl_usdhc2_pins>;
> +	cd-gpios = <&gpio2 12 GPIO_ACTIVE_LOW>;
> +	vmmc-supply = <&reg_usdhc2_vmmc>;
> +	bus-width = <4>;
> +	status = "okay";
> +};
> +
> +&iomuxc {
> +	pinctrl_i2c2: i2c2grp {
> +		fsl,pins = <
> +			MX8MP_IOMUXC_I2C2_SCL__I2C2_SCL		0x400001c3
> +			MX8MP_IOMUXC_I2C2_SDA__I2C2_SDA		0x400001c3
> +		>;
> +	};
> +
> +	pinctrl_i2c2_gpio: i2c2gpiogrp {
> +		fsl,pins = <
> +			MX8MP_IOMUXC_I2C2_SCL__GPIO5_IO16	0x1e3
> +			MX8MP_IOMUXC_I2C2_SDA__GPIO5_IO17	0x1e3
> +		>;
> +	};
> +
> +	pinctrl_reg_usdhc2_vmmc: regusdhc2vmmcgrp {
> +		fsl,pins = <
> +			MX8MP_IOMUXC_SD2_RESET_B__GPIO2_IO19	0x41
> +		>;
> +	};
> +
> +	pinctrl_uart2: uart2grp {
> +		fsl,pins = <
> +			MX8MP_IOMUXC_UART2_RXD__UART2_DCE_RX	0x49
> +			MX8MP_IOMUXC_UART2_TXD__UART2_DCE_TX	0x49
> +		>;
> +	};
> +
> +	pinctrl_usdhc2_pins: usdhc2-gpiogrp {
> +		fsl,pins = <
> +			MX8MP_IOMUXC_SD2_CD_B__GPIO2_IO12	0x1c4
> +		>;
> +	};
> +
> +	pinctrl_usdhc2: usdhc2grp {
> +		fsl,pins = <
> +			MX8MP_IOMUXC_SD2_CLK__USDHC2_CLK	0x190
> +			MX8MP_IOMUXC_SD2_CMD__USDHC2_CMD	0x1d0
> +			MX8MP_IOMUXC_SD2_DATA0__USDHC2_DATA0	0x1d0
> +			MX8MP_IOMUXC_SD2_DATA1__USDHC2_DATA1	0x1d0
> +			MX8MP_IOMUXC_SD2_DATA2__USDHC2_DATA2	0x1d0
> +			MX8MP_IOMUXC_SD2_DATA3__USDHC2_DATA3	0x1d0
> +			MX8MP_IOMUXC_GPIO1_IO04__USDHC2_VSELECT	0xc1
> +		>;
> +	};
> +
> +	pinctrl_usdhc2_100mhz: usdhc2-100mhzgrp {
> +		fsl,pins = <
> +			MX8MP_IOMUXC_SD2_CLK__USDHC2_CLK	0x194
> +			MX8MP_IOMUXC_SD2_CMD__USDHC2_CMD	0x1d4
> +			MX8MP_IOMUXC_SD2_DATA0__USDHC2_DATA0	0x1d4
> +			MX8MP_IOMUXC_SD2_DATA1__USDHC2_DATA1	0x1d4
> +			MX8MP_IOMUXC_SD2_DATA2__USDHC2_DATA2	0x1d4
> +			MX8MP_IOMUXC_SD2_DATA3__USDHC2_DATA3	0x1d4
> +			MX8MP_IOMUXC_GPIO1_IO04__USDHC2_VSELECT	0xc1
> +		>;
> +	};
> +
> +	pinctrl_usdhc2_200mhz: usdhc2-200mhzgrp {
> +		fsl,pins = <
> +			MX8MP_IOMUXC_SD2_CLK__USDHC2_CLK	0x196
> +			MX8MP_IOMUXC_SD2_CMD__USDHC2_CMD	0x1d6
> +			MX8MP_IOMUXC_SD2_DATA0__USDHC2_DATA0	0x1d6
> +			MX8MP_IOMUXC_SD2_DATA1__USDHC2_DATA1	0x1d6
> +			MX8MP_IOMUXC_SD2_DATA2__USDHC2_DATA2	0x1d6
> +			MX8MP_IOMUXC_SD2_DATA3__USDHC2_DATA3	0x1d6
> +			MX8MP_IOMUXC_GPIO1_IO04__USDHC2_VSELECT	0xc1
> +		>;
> +	};
> +};
> diff --git a/arch/arm64/boot/dts/freescale/imx8mp-phycore-som.dtsi
> b/arch/arm64/boot/dts/freescale/imx8mp-phycore-som.dtsi new file mode
> 100644
> index 000000000000..8618df68b1e5
> --- /dev/null
> +++ b/arch/arm64/boot/dts/freescale/imx8mp-phycore-som.dtsi
> @@ -0,0 +1,296 @@
> +// SPDX-License-Identifier: GPL-2.0
> +/*
> + * Copyright (C) 2020 PHYTEC Messtechnik GmbH
> + * Author: Teresa Remmet <t.remmet@xxxxxxxxx>
> + */
> +
> +#include <dt-bindings/net/ti-dp83867.h>
> +#include "imx8mp.dtsi"
> +
> +/ {
> +	model = "PHYTEC phyCORE-i.MX8MP";
> +	compatible = "phytec,imx8mp-phycore-som", "fsl,imx8mp";
> +
> +	aliases {
> +		rtc0 = &rv3028;
> +		rtc1 = &snvs_rtc;
> +	};
> +
> +	memory@40000000 {
> +		device_type = "memory";
> +		reg = <0x0 0x40000000 0 0x80000000>;
> +	};
> +};
> +
> +&A53_0 {
> +	cpu-supply = <&buck2>;
> +};
> +
> +&A53_1 {
> +	cpu-supply = <&buck2>;
> +};
> +
> +&A53_2 {
> +	cpu-supply = <&buck2>;
> +};
> +
> +&A53_3 {
> +	cpu-supply = <&buck2>;
> +};
> +
> +/* ethernet 1 */
> +&fec {
> +	pinctrl-names = "default";
> +	pinctrl-0 = <&pinctrl_fec>;
> +	phy-mode = "rgmii-id";
> +	phy-handle = <&ethphy1>;
> +	fsl,magic-packet;
> +	status = "okay";
> +
> +	mdio {
> +		#address-cells = <1>;
> +		#size-cells = <0>;
> +
> +		ethphy1: ethernet-phy@0 {
> +			compatible = "ethernet-phy-ieee802.3-c22";
> +			reg = <0>;
> +			interrupt-parent = <&gpio1>;
> +			interrupts = <15 IRQ_TYPE_EDGE_FALLING>;
> +			ti,rx-internal-delay = <DP83867_RGMIIDCTL_2_00_NS>;
> +			ti,tx-internal-delay = <DP83867_RGMIIDCTL_2_00_NS>;
> +			ti,fifo-depth = <DP83867_PHYCR_FIFO_DEPTH_4_B_NIB>;
> +			ti,clk-output-sel = <DP83867_CLK_O_SEL_OFF>;
> +			enet-phy-lane-no-swap;
> +		};
> +	};
> +};
> +
> +&i2c1 {
> +	clock-frequency = <400000>;
> +	pinctrl-names = "default";
> +	pinctrl-0 = <&pinctrl_i2c1>;
> +	pinctrl-1 = <&pinctrl_i2c1_gpio>;
> +	sda-gpios = <&gpio5 15 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
> +	scl-gpios = <&gpio5 14 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
> +	status = "okay";
> +
> +	pmic: pmic@25 {
> +		reg = <0x25>;
> +		compatible = "nxp,pca9450c";
> +		pinctrl-names = "default";
> +		pinctrl-0 = <&pinctrl_pmic>;
> +		interrupt-parent = <&gpio4>;
> +		interrupts = <18 IRQ_TYPE_LEVEL_LOW>;
> +
> +		regulators {
> +			buck1: BUCK1 {
> +				regulator-compatible = "BUCK1";
> +				regulator-min-microvolt = <600000>;
> +				regulator-max-microvolt = <2187500>;
> +				regulator-boot-on;
> +				regulator-always-on;
> +				regulator-ramp-delay = <3125>;
> +			};
> +
> +			buck2: BUCK2 {
> +				regulator-compatible = "BUCK2";
> +				regulator-min-microvolt = <600000>;
> +				regulator-max-microvolt = <2187500>;
> +				regulator-boot-on;
> +				regulator-always-on;
> +				regulator-ramp-delay = <3125>;
> +			};
> +
> +			buck4: BUCK4 {
> +				regulator-compatible = "BUCK4";
> +				regulator-min-microvolt = <600000>;
> +				regulator-max-microvolt = <3400000>;
> +				regulator-boot-on;
> +				regulator-always-on;
> +			};
> +
> +			buck5: BUCK5 {
> +				regulator-compatible = "BUCK5";
> +				regulator-min-microvolt = <600000>;
> +				regulator-max-microvolt = <3400000>;
> +				regulator-boot-on;
> +				regulator-always-on;
> +			};
> +
> +			buck6: BUCK6 {
> +				regulator-compatible = "BUCK6";
> +				regulator-min-microvolt = <600000>;
> +				regulator-max-microvolt = <3400000>;
> +				regulator-boot-on;
> +				regulator-always-on;
> +			};
> +
> +			ldo1: LDO1 {
> +				regulator-compatible = "LDO1";
> +				regulator-min-microvolt = <1600000>;
> +				regulator-max-microvolt = <3300000>;
> +				regulator-boot-on;
> +				regulator-always-on;
> +			};
> +
> +			ldo2: LDO2 {
> +				regulator-compatible = "LDO2";
> +				regulator-min-microvolt = <800000>;
> +				regulator-max-microvolt = <1150000>;
> +				regulator-boot-on;
> +				regulator-always-on;
> +			};
> +
> +			ldo3: LDO3 {
> +				regulator-compatible = "LDO3";
> +				regulator-min-microvolt = <800000>;
> +				regulator-max-microvolt = <3300000>;
> +				regulator-boot-on;
> +				regulator-always-on;
> +			};
> +
> +			ldo4: LDO4 {
> +				regulator-compatible = "LDO4";
> +				regulator-min-microvolt = <800000>;
> +				regulator-max-microvolt = <3300000>;
> +				regulator-boot-on;
> +				regulator-always-on;
> +			};
> +
> +			ldo5: LDO5 {
> +				regulator-compatible = "LDO5";
> +				regulator-min-microvolt = <1800000>;
> +				regulator-max-microvolt = <3300000>;
> +			};
> +		};
> +	};
> +
> +	eeprom@51 {
> +		compatible = "atmel,24c32";
> +		reg = <0x51>;
> +		pagesize = <32>;
> +		status = "okay";
> +	};
> +
> +	rv3028: rtc@52 {
> +		compatible = "microcrystal,rv3028";
> +		reg = <0x52>;
> +		trickle-resistor-ohms = <1000>;
> +		enable-level-switching-mode;
> +		status = "okay";
> +	};
> +};
> +
> +/* eMMC */
> +&usdhc3 {
> +	pinctrl-names = "default", "state_100mhz", "state_200mhz";
> +	pinctrl-0 = <&pinctrl_usdhc3>;
> +	pinctrl-1 = <&pinctrl_usdhc3_100mhz>;
> +	pinctrl-2 = <&pinctrl_usdhc3_200mhz>;
> +	bus-width = <8>;
> +	non-removable;
> +	status = "okay";
> +};
> +
> +&wdog1 {
> +	pinctrl-names = "default";
> +	pinctrl-0 = <&pinctrl_wdog>;
> +	fsl,ext-reset-output;
> +	status = "okay";
> +};
> +
> +&iomuxc {
> +	pinctrl_fec: fecgrp {
> +		fsl,pins = <
> +			MX8MP_IOMUXC_SAI1_RXD2__ENET1_MDC		0x3
> +			MX8MP_IOMUXC_SAI1_RXD3__ENET1_MDIO		0x3
> +			MX8MP_IOMUXC_SAI1_RXD4__ENET1_RGMII_RD0		0x91
> +			MX8MP_IOMUXC_SAI1_RXD5__ENET1_RGMII_RD1		0x91
> +			MX8MP_IOMUXC_SAI1_RXD6__ENET1_RGMII_RD2		0x91
> +			MX8MP_IOMUXC_SAI1_RXD7__ENET1_RGMII_RD3		0x91
> +			MX8MP_IOMUXC_SAI1_TXC__ENET1_RGMII_RXC		0x91
> +			MX8MP_IOMUXC_SAI1_TXFS__ENET1_RGMII_RX_CTL	0x91
> +			MX8MP_IOMUXC_SAI1_TXD0__ENET1_RGMII_TD0		0x1f
> +			MX8MP_IOMUXC_SAI1_TXD1__ENET1_RGMII_TD1		0x1f
> +			MX8MP_IOMUXC_SAI1_TXD2__ENET1_RGMII_TD2		0x1f
> +			MX8MP_IOMUXC_SAI1_TXD3__ENET1_RGMII_TD3		0x1f
> +			MX8MP_IOMUXC_SAI1_TXD4__ENET1_RGMII_TX_CTL	0x1f
> +			MX8MP_IOMUXC_SAI1_TXD5__ENET1_RGMII_TXC		0x1f
> +			MX8MP_IOMUXC_GPIO1_IO15__GPIO1_IO15		0x11
> +		>;
> +	};
> +
> +	pinctrl_i2c1: i2c1grp {
> +		fsl,pins = <
> +			MX8MP_IOMUXC_I2C1_SCL__I2C1_SCL		0x400001c3
> +			MX8MP_IOMUXC_I2C1_SDA__I2C1_SDA		0x400001c3
> +		>;
> +	};
> +
> +	pinctrl_i2c1_gpio: i2c1gpiogrp {
> +		fsl,pins = <
> +			MX8MP_IOMUXC_I2C1_SCL__GPIO5_IO14	0x1e3
> +			MX8MP_IOMUXC_I2C1_SDA__GPIO5_IO15	0x1e3
> +		>;
> +	};
> +
> +	pinctrl_pmic: pmicirqgrp {
> +		fsl,pins = <
> +			MX8MP_IOMUXC_SAI1_TXD6__GPIO4_IO18	0x141
> +		>;
> +	};
> +
> +	pinctrl_usdhc3: usdhc3grp {
> +		fsl,pins = <
> +			MX8MP_IOMUXC_NAND_WE_B__USDHC3_CLK	0x190
> +			MX8MP_IOMUXC_NAND_WP_B__USDHC3_CMD	0x1d0
> +			MX8MP_IOMUXC_NAND_DATA04__USDHC3_DATA0	0x1d0
> +			MX8MP_IOMUXC_NAND_DATA05__USDHC3_DATA1	0x1d0
> +			MX8MP_IOMUXC_NAND_DATA06__USDHC3_DATA2	0x1d0
> +			MX8MP_IOMUXC_NAND_DATA07__USDHC3_DATA3	0x1d0
> +			MX8MP_IOMUXC_NAND_RE_B__USDHC3_DATA4	0x1d0
> +			MX8MP_IOMUXC_NAND_CE2_B__USDHC3_DATA5	0x1d0
> +			MX8MP_IOMUXC_NAND_CE3_B__USDHC3_DATA6	0x1d0
> +			MX8MP_IOMUXC_NAND_CLE__USDHC3_DATA7	0x1d0
> +			MX8MP_IOMUXC_NAND_CE1_B__USDHC3_STROBE	0x190
> +		>;
> +	};
> +
> +	pinctrl_usdhc3_100mhz: usdhc3-100mhzgrp {
> +		fsl,pins = <
> +			MX8MP_IOMUXC_NAND_WE_B__USDHC3_CLK	0x194
> +			MX8MP_IOMUXC_NAND_WP_B__USDHC3_CMD	0x1d4
> +			MX8MP_IOMUXC_NAND_DATA04__USDHC3_DATA0	0x1d4
> +			MX8MP_IOMUXC_NAND_DATA05__USDHC3_DATA1	0x1d4
> +			MX8MP_IOMUXC_NAND_DATA06__USDHC3_DATA2	0x1d4
> +			MX8MP_IOMUXC_NAND_DATA07__USDHC3_DATA3	0x1d4
> +			MX8MP_IOMUXC_NAND_RE_B__USDHC3_DATA4	0x1d4
> +			MX8MP_IOMUXC_NAND_CE2_B__USDHC3_DATA5	0x1d4
> +			MX8MP_IOMUXC_NAND_CE3_B__USDHC3_DATA6	0x1d4
> +			MX8MP_IOMUXC_NAND_CLE__USDHC3_DATA7	0x1d4
> +			MX8MP_IOMUXC_NAND_CE1_B__USDHC3_STROBE	0x194
> +		>;
> +	};
> +
> +	pinctrl_usdhc3_200mhz: usdhc3-200mhzgrp {
> +		fsl,pins = <
> +			MX8MP_IOMUXC_NAND_WE_B__USDHC3_CLK	0x196
> +			MX8MP_IOMUXC_NAND_WP_B__USDHC3_CMD	0x1d6
> +			MX8MP_IOMUXC_NAND_DATA04__USDHC3_DATA0	0x1d6
> +			MX8MP_IOMUXC_NAND_DATA05__USDHC3_DATA1	0x1d6
> +			MX8MP_IOMUXC_NAND_DATA06__USDHC3_DATA2	0x1d6
> +			MX8MP_IOMUXC_NAND_DATA07__USDHC3_DATA3	0x1d6
> +			MX8MP_IOMUXC_NAND_RE_B__USDHC3_DATA4	0x1d6
> +			MX8MP_IOMUXC_NAND_CE2_B__USDHC3_DATA5	0x1d6
> +			MX8MP_IOMUXC_NAND_CE3_B__USDHC3_DATA6	0x1d6
> +			MX8MP_IOMUXC_NAND_CLE__USDHC3_DATA7	0x1d6
> +			MX8MP_IOMUXC_NAND_CE1_B__USDHC3_STROBE	0x196
> +		>;
> +	};
> +
> +	pinctrl_wdog: wdoggrp {
> +		fsl,pins = <
> +			MX8MP_IOMUXC_GPIO1_IO02__WDOG1_WDOG_B	0xc6
> +		>;
> +	};
> +};


-- 
Alexander Dahl           Thorsis Technologies GmbH   T +49 391 544 563 1000
Industrieautomation      Oststr. 18                  F +49 391 544 563 9099
T +49 391 544 563 3036   39114 Magdeburg             https://www.thorsis.com/

Sitz der Gesellschaft: Magdeburg
Amtsgericht Stendal HRB 110339
Geschäftsführer: Dipl.-Ing. Thorsten Szczepanski







[Index of Archives]     [Device Tree Compilter]     [Device Tree Spec]     [Linux Driver Backports]     [Video for Linux]     [Linux USB Devel]     [Linux PCI Devel]     [Linux Audio Users]     [Linux Kernel]     [Linux SCSI]     [XFree86]     [Yosemite Backpacking]


  Powered by Linux