On Fri, Dec 11, 2020 at 07:20:41AM +0100, 'Greg Kroah-Hartman' wrote:
> On Fri, Dec 11, 2020 at 06:09:43AM +0000, József Horváth wrote:
> > On Fri, Dec 11, 2020 at 06:50:58AM +0100, 'Greg Kroah-Hartman' wrote:
> > > On Thu, Dec 10, 2020 at 07:46:25PM +0000, József Horváth wrote:
> > > > On Thu, Dec 10, 2020 at 08:03:22PM +0100, 'Greg Kroah-Hartman' wrote:
> > > > > On Thu, Dec 10, 2020 at 05:04:46PM +0000, József Horváth wrote:
> > > > > > This is a serial port driver for
> > > > > > Silicon Labs Si4455 Sub-GHz transciver.
> > > > > > +
> > > > > > +#define BASE_TTYIOC_PRIVATE 0xA0
> > > > > > +/* Set EZConfig.
> > > > > > + * After this ioctl call, the driver restarts the si4455,
> > > > > > + * then apply the new configuration and patch.
> > > > > > + */
> > > > > > +#define SI4455_IOC_SEZC _IOW('T', \
> > > > > > + BASE_TTYIOC_PRIVATE + 0x01, \
> > > > > > + struct si4455_iocbuff)
> > > > >
> > > > > Why does a serial driver have private ioctls? Please no, don't do that.
> > > >
> > > > I checked the ioctl.h and serial_core.h, but I not found any similar definition, like BASE_VIDIOC_PRIVATE in videodev2.h.
> > > > In this case the name of macro BASE_TTYIOC_PRIVATE means the base value of special ioctl commands owned by this driver.
> > >
> > > My point is, a serial driver should NOT have any custom ioctls.
> > >
> > > > I can change it to BASE_TTYIOC or SI4455_IOC_BASE
> > > >
> > > > > Implement the basic serial driver first, and then we can talk about
> > > > > "custom" configurations and the like, using the correct apis.
> > > >
> > > > Without the SI4455_IOC_SEZC call, the driver can't configure the Si4455 and not working at all.
> > > > The cofiguration for interface is provided by user for application.
> > >
> > > That is what a device tree is for, to configure the device to have the
> > > correct system configuration, why can't that be the same here?
> > >
> > > > It contains the base frequency, channel spacing, modulation, and a lot
> > > > of more stuff, and generated by Silicon Labs Wireless Development
> > > > Suite.
> > > > The generated configuration is in a non public(compressed,
> > > > encrypted...who knows) format, so without this the driver can't
> > > > provide configuration parameters to Si4455.
> > >
> > > So we have to take a "custom" userspace blob and send it to the device
> > > to configure it properly? Like Jiri said, sounds like firmware, so just
> > > use that interface instead.
> >
> > I checked Jiri's suggestion, and it is a good solution to replace SI4455_IOC_SEZC(configuration) and SI4455_IOC_SEZP(firmware patch).
> > I can move SI4455_IOC_SSIZ(package size) to device tree property.
> >
> > Maybe you have good suggestion for the following:
> > SI4455_IOC_STXC -> Radio transmit channel index. It is a real use case to control this parameter by user at runtime.
> > SI4455_IOC_SRXC -> Radio receive channel index. It is a real use case to control this parameter by user at runtime.
>
> These are not serial port things, why would a serial port care about
> these?
You are right, these are not regular serial port things, but this device is not a regular uart, it is a sub-GHz transciever, digital radio.
This driver tries to represent it as a serial port to user.
>
> > SI4455_IOC_GRSSI -> Last measured RSSI, when packet received. This is a useful information.
> > (Currently I'm the only one user, and I need this :) )
>
> What is "RSSI"?
>
> And why not debugfs if it's only debugging stuff?
Received signal strength indication, and not only debugging. It is an information for the end user.
>
> thanks,
>
> greg k-h
Üdvözlettel / Best regards:
József Horváth
