Re: [PATCH v3 2/4] gpio: visconti: Add Toshiba Visconti GPIO support

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



Hi,

Thanks for your review.

On Thu, Dec 03, 2020 at 07:03:27PM +0900, Punit Agrawal wrote:
> Hi Iwamatsu-san,
> 
> A couple of very minor comments below -
> 
> Nobuhiro Iwamatsu <nobuhiro1.iwamatsu@xxxxxxxxxxxxx> writes:
> 
> > Add the GPIO driver for Toshiba Visconti ARM SoCs.
> >
> > Signed-off-by: Nobuhiro Iwamatsu <nobuhiro1.iwamatsu@xxxxxxxxxxxxx>
> > ---
> >  drivers/gpio/Kconfig                      |   9 +
> >  drivers/gpio/Makefile                     |   1 +
> >  drivers/gpio/gpio-visconti.c              | 232 ++++++++++++++++++++++
> >  drivers/pinctrl/visconti/pinctrl-common.c |  23 +++
> >  4 files changed, 265 insertions(+)
> >  create mode 100644 drivers/gpio/gpio-visconti.c
> >
> 
> [...]
> 
> > diff --git a/drivers/gpio/gpio-visconti.c b/drivers/gpio/gpio-visconti.c
> > new file mode 100644
> > index 000000000000..17e6da161f48
> > --- /dev/null
> > +++ b/drivers/gpio/gpio-visconti.c
> > @@ -0,0 +1,232 @@
> > +// SPDX-License-Identifier: GPL-2.0
> > +/*
> > + * Toshiba Visconti GPIO Support
> > + *
> > + * (C) Copyright 2020 Toshiba Electronic Devices & Storage Corporation
> > + * (C) Copyright 2020 Nobuhiro Iwamatsu <nobuhiro1.iwamatsu@xxxxxxxxxxxxx>
> > + */
> > +
> > +#include <linux/init.h>
> > +#include <linux/interrupt.h>
> > +#include <linux/module.h>
> > +#include <linux/io.h>
> > +#include <linux/platform_device.h>
> > +#include <linux/gpio/driver.h>
> > +#include <linux/of.h>
> > +#include <linux/bitops.h>
> > +
> > +/* register offset */
> > +#define GPIO_DIR	0x00
> > +#define GPIO_IDATA	0x08
> > +#define GPIO_ODATA	0x10
> > +#define GPIO_OSET	0x18
> > +#define GPIO_OCLR	0x20
> > +#define GPIO_INTMODE	0x30
> > +
> > +#define VISCONTI_GPIO_NR	32
> 
> The macro doesn't seem to be used. Can we drop this? On the other hand
> should there be a macro to indicate the maximum number of GPIO lines
> that support interrupt (16)?

Thanks, I will drop this macro.
And about interrutp, it supports with this patch.

> 
> > +
> > +struct visconti_gpio {
> > +	void __iomem *base;
> > +	int *irq;
> > +	spinlock_t lock; /* protect gpio register */
> > +	struct device *dev;
> > +	struct gpio_chip gpio_chip;
> > +	struct irq_chip irq_chip;
> > +};
> > +
> > +static void visconti_gpio_irq_mask(struct irq_data *d)
> > +{
> > +	struct gpio_chip *gc = irq_data_get_irq_chip_data(d);
> > +	struct visconti_gpio *priv = gpiochip_get_data(gc);
> > +
> > +	disable_irq_nosync(priv->irq[irqd_to_hwirq(d)]);
> > +}
> > +
> > +static void visconti_gpio_irq_unmask(struct irq_data *d)
> > +{
> > +	struct gpio_chip *gc = irq_data_get_irq_chip_data(d);
> > +	struct visconti_gpio *priv = gpiochip_get_data(gc);
> > +
> > +	enable_irq(priv->irq[irqd_to_hwirq(d)]);
> > +}
> > +
> > +static int visconti_gpio_irq_set_type(struct irq_data *d, unsigned int type)
> > +{
> > +	struct gpio_chip *gc = irq_data_get_irq_chip_data(d);
> > +	struct visconti_gpio *priv = gpiochip_get_data(gc);
> > +	u32 offset = irqd_to_hwirq(d);
> > +	u32 bit = BIT(offset);
> > +	u32 intc_type = IRQ_TYPE_EDGE_RISING;
> > +	u32 intmode, odata;
> > +	int ret = 0;
> > +	unsigned long flags;
> > +
> > +	spin_lock_irqsave(&priv->lock, flags);
> > +
> > +	odata = readl(priv->base + GPIO_ODATA);
> > +	intmode = readl(priv->base + GPIO_INTMODE);
> > +
> > +	switch (type) {
> > +	case IRQ_TYPE_EDGE_RISING:
> > +		odata &= ~bit;
> > +		intmode &= ~bit;
> > +		break;
> > +	case IRQ_TYPE_EDGE_FALLING:
> > +		odata |= bit;
> > +		intmode &= ~bit;
> > +		break;
> > +	case IRQ_TYPE_EDGE_BOTH:
> > +		intmode |= bit;
> > +		break;
> > +	case IRQ_TYPE_LEVEL_HIGH:
> > +		intc_type = IRQ_TYPE_LEVEL_HIGH;
> > +		odata &= ~bit;
> > +		intmode &= ~bit;
> > +		break;
> > +	case IRQ_TYPE_LEVEL_LOW:
> > +		intc_type = IRQ_TYPE_LEVEL_HIGH;
> > +		odata |= bit;
> > +		intmode &= ~bit;
> > +		break;
> > +	default:
> > +		ret = -EINVAL;
> > +		goto err;
> > +	}
> > +
> > +	writel(odata, priv->base + GPIO_ODATA);
> > +	writel(intmode, priv->base + GPIO_INTMODE);
> > +	irq_set_irq_type(priv->irq[offset], intc_type);
> > +err:
> > +	spin_unlock_irqrestore(&priv->lock, flags);
> > +
> > +	return ret;
> > +}
> > +
> > +static irqreturn_t visconti_gpio_irq_handler(int irq, void *dev_id)
> > +{
> > +	struct visconti_gpio *priv = dev_id;
> > +	u32 offset = irq - priv->irq[0];
> > +
> > +	generic_handle_irq(irq_find_mapping(priv->gpio_chip.irq.domain, offset));
> > +
> > +	return IRQ_HANDLED;
> > +}
> > +
> > +static void visconti_init_irq_valid_mask(struct gpio_chip *chip, unsigned long *valid_mask,
> > +					 unsigned int ngpios)
> > +{
> > +	int i;
> > +
> > +	/* Exclude GPIO pins 16-31 from irq */
> > +	for (i = 16; i < ngpios; i++)
> > +		clear_bit(i, valid_mask);
> > +}
> > +
> > +static int visconti_gpio_probe(struct platform_device *pdev)
> > +{
> > +	struct device *dev = &pdev->dev;
> > +	struct visconti_gpio *priv;
> > +	struct irq_chip *irq_chip;
> > +	struct irq_desc *desc;
> > +	struct gpio_irq_chip *girq;
> > +	const char *name = dev_name(dev);
> > +	int i, ret, num_irq;
> > +
> > +	priv = devm_kzalloc(dev, sizeof(*priv), GFP_KERNEL);
> > +	if (!priv)
> > +		return -ENOMEM;
> > +
> > +	priv->dev = dev;
> > +	spin_lock_init(&priv->lock);
> > +
> > +	priv->base = devm_platform_ioremap_resource(pdev, 0);
> > +	if (IS_ERR(priv->base))
> > +		return PTR_ERR(priv->base);
> > +
> > +	ret = platform_irq_count(pdev);
> > +	if (!ret) {
> > +		dev_err(dev, "Couldn't determine # GPIO banks\n");
> > +		return -ENOENT;
> > +	}
> 
> platform_irq_count() can return -EPROBE_DEFER. Is that something that
> should be handled?

I see. In case of an error, I will change it to return ret directly.

> 
> With the above two comments addressed, feel free to add 
> 
> Reviewed-by: Punit Agrawal <punit1.agrawal@xxxxxxxxxxxxx>
> 

Thank you.

> Thanks,
> Punit
> 

Best regards.,
  Nobuhiro

> 
> > +	num_irq = ret;
> > +
> > +	priv->irq = devm_kcalloc(dev, num_irq, sizeof(priv->irq), GFP_KERNEL);
> > +	if (!priv->irq)
> > +		return -ENOMEM;
> > +
> > +	for (i = 0; i < num_irq; i++) {
> > +		priv->irq[i] = platform_get_irq(pdev, i);
> > +		if (priv->irq[i] < 0) {
> > +			dev_err(dev, "invalid IRQ[%d]\n", i);
> > +			return priv->irq[i];
> > +		}
> > +	}
> > +
> > +	ret = bgpio_init(&priv->gpio_chip, dev, 4,
> > +			 priv->base + GPIO_IDATA,
> > +			 priv->base + GPIO_OSET,
> > +			 priv->base + GPIO_OCLR,
> > +			 priv->base + GPIO_DIR,
> > +			 NULL,
> > +			 0);
> > +	if (ret) {
> > +		dev_err(dev, "unable to init generic GPIO\n");
> > +		return ret;
> > +	}
> > +
> > +	priv->gpio_chip.irq.init_valid_mask = visconti_init_irq_valid_mask;
> > +
> > +	irq_chip = &priv->irq_chip;
> > +	irq_chip->name = "gpio-visconti";
> > +	irq_chip->irq_mask = visconti_gpio_irq_mask;
> > +	irq_chip->irq_unmask = visconti_gpio_irq_unmask;
> > +	irq_chip->irq_set_type = visconti_gpio_irq_set_type;
> > +	irq_chip->flags = IRQCHIP_SET_TYPE_MASKED | IRQCHIP_MASK_ON_SUSPEND;
> > +
> > +	girq = &priv->gpio_chip.irq;
> > +	girq->chip = irq_chip;
> > +	/* This will let us handle the parent IRQ in the driver */
> > +	girq->parent_handler = NULL;
> > +	girq->num_parents = 0;
> > +	girq->parents = NULL;
> > +	girq->default_type = IRQ_TYPE_NONE;
> > +	girq->handler = handle_level_irq;
> > +
> > +	ret = devm_gpiochip_add_data(dev, &priv->gpio_chip, priv);
> > +	if (ret) {
> > +		dev_err(dev, "failed to add GPIO chip\n");
> > +		return ret;
> > +	}
> > +
> > +	for (i = 0; i < num_irq; i++) {
> > +		desc = irq_to_desc(priv->irq[i]);
> > +		desc->status_use_accessors |= IRQ_NOAUTOEN;
> > +		if (devm_request_irq(dev, priv->irq[i],
> > +				     visconti_gpio_irq_handler, 0, name, priv)) {
> > +			dev_err(dev, "failed to request IRQ[%d]\n", i);
> > +			return -ENOENT;
> > +		}
> > +	}
> > +
> > +	return ret;
> > +}
> > +
> > +static const struct of_device_id visconti_gpio_of_match[] = {
> > +	{ .compatible = "toshiba,gpio-tmpv7708", },
> > +	{ /* end of table */ }
> > +};
> > +MODULE_DEVICE_TABLE(of, visconti_gpio_of_match);
> > +
> > +static struct platform_driver visconti_gpio_driver = {
> > +	.probe		= visconti_gpio_probe,
> > +	.driver		= {
> > +		.name	= "visconti_gpio",
> > +		.of_match_table = of_match_ptr(visconti_gpio_of_match),
> > +	}
> > +};
> > +module_platform_driver(visconti_gpio_driver);
> > +
> > +MODULE_AUTHOR("Toshiba Electronic Devices & Storage Corporation");
> > +MODULE_AUTHOR("Nobuhiro Iwamatsu <nobuhiro1.iwamatsu@xxxxxxxxxxxxx>");
> > +MODULE_DESCRIPTION("Toshiba Visconti GPIO Driver");
> > +MODULE_LICENSE("GPL v2");
> 
> [...]
> 
> 



[Index of Archives]     [Device Tree Compilter]     [Device Tree Spec]     [Linux Driver Backports]     [Video for Linux]     [Linux USB Devel]     [Linux PCI Devel]     [Linux Audio Users]     [Linux Kernel]     [Linux SCSI]     [XFree86]     [Yosemite Backpacking]


  Powered by Linux