This patch adds new host controller driver for
Fujitsu SDHCI controller f_sdh30.
Signed-off-by: Vincent Yang <Vincent.Yang@xxxxxxxxxxxxxx>
---
.../devicetree/bindings/mmc/sdhci-fujitsu.txt | 35 +++
drivers/mmc/host/Kconfig | 7 +
drivers/mmc/host/Makefile | 1 +
drivers/mmc/host/sdhci_f_sdh30.c | 346 +++++++++++++++++++++
drivers/mmc/host/sdhci_f_sdh30.h | 40 +++
5 files changed, 429 insertions(+)
create mode 100644 Documentation/devicetree/bindings/mmc/sdhci-fujitsu.txt
create mode 100644 drivers/mmc/host/sdhci_f_sdh30.c
create mode 100644 drivers/mmc/host/sdhci_f_sdh30.h
diff --git a/Documentation/devicetree/bindings/mmc/sdhci-fujitsu.txt b/Documentation/devicetree/bindings/mmc/sdhci-fujitsu.txt
new file mode 100644
index 0000000..40add438
--- /dev/null
+++ b/Documentation/devicetree/bindings/mmc/sdhci-fujitsu.txt
@@ -0,0 +1,35 @@
+* Fujitsu SDHCI controller
+
+This file documents differences between the core properties in mmc.txt
+and the properties used by the sdhci_f_sdh30 driver.
+
+Required properties:
+- compatible: "fujitsu,f_sdh30"
+- voltage-ranges : two cells are required, first cell specifies minimum
+ slot voltage (mV), second cell specifies maximum slot voltage (mV).
+ Several ranges could be specified.
+
+Optional properties:
+- gpios: This is one optional gpio for controlling a power mux which
+ switches between two power supplies. 3.3V is selected when gpio is high,
+ and 1.8V is selected when gpio is low. This voltage is used for signal
+ level.
+- clocks: Must contain an entry for each entry in clock-names. It is a
+ list of phandles and clock-specifier pairs.
+ See ../clocks/clock-bindings.txt for details.
+- clock-names: Should contain the following two entries:
+ "sd_sd4clk" - clock primarily used for tuning process
+ "sd_bclk" - base clock for sdhci controller
+
+Example:
+
+ sdhci1: sdio@36600000 {
+ compatible = "fujitsu,f_sdh30";
+ reg = <0 0x36600000 0x1000>;
+ interrupts = <0 172 0x4>,
+ <0 173 0x4>;
+ voltage-ranges = <1800 1800 3300 3300>;
+ gpios = <&gpio0 7 0>;
+ clocks = <&clk_hdmi_2_0>, <&clk_hdmi_3_0>;
+ clock-names = "sd_sd4clk", "sd_bclk";
+ };
diff --git a/drivers/mmc/host/Kconfig b/drivers/mmc/host/Kconfig
index 7fee224..a1f3207 100644
--- a/drivers/mmc/host/Kconfig
+++ b/drivers/mmc/host/Kconfig
@@ -281,6 +281,13 @@ config MMC_SDHCI_BCM2835
This selects the BCM2835 SD/MMC controller. If you have a BCM2835
platform with SD or MMC devices, say Y or M here.
+config MMC_SDHCI_F_SDH30
+ tristate "SDHCI support for Fujitsu Semiconductor F_SDH30"
+ depends on MMC_SDHCI && (ARCH_MB8AC0300 || ARCH_MB86S70)
+ help
+ This selects the Secure Digital Host Controller Interface (SDHCI)
+ Needed by some Fujitsu SoC for MMC / SD / SDIO support.
+ If you have a controller with this interface, say Y or M here.
If unsure, say N.
config MMC_MOXART
diff --git a/drivers/mmc/host/Makefile b/drivers/mmc/host/Makefile
index 7f81ddf..a4c89e5 100644
--- a/drivers/mmc/host/Makefile
+++ b/drivers/mmc/host/Makefile
@@ -15,6 +15,7 @@ obj-$(CONFIG_MMC_SDHCI_PXAV3) += sdhci-pxav3.o
obj-$(CONFIG_MMC_SDHCI_PXAV2) += sdhci-pxav2.o
obj-$(CONFIG_MMC_SDHCI_S3C) += sdhci-s3c.o
obj-$(CONFIG_MMC_SDHCI_SIRF) += sdhci-sirf.o
+obj-$(CONFIG_MMC_SDHCI_F_SDH30) += sdhci_f_sdh30.o
obj-$(CONFIG_MMC_SDHCI_SPEAR) += sdhci-spear.o
obj-$(CONFIG_MMC_WBSD) += wbsd.o
obj-$(CONFIG_MMC_AU1X) += au1xmmc.o
diff --git a/drivers/mmc/host/sdhci_f_sdh30.c b/drivers/mmc/host/sdhci_f_sdh30.c
new file mode 100644
index 0000000..6fae509
--- /dev/null
+++ b/drivers/mmc/host/sdhci_f_sdh30.c
@@ -0,0 +1,346 @@
+/*
+ * linux/drivers/mmc/host/sdhci_f_sdh30.c
+ *
+ * Copyright (C) 2013 - 2014 Fujitsu Semiconductor, Ltd
+ * Vincent Yang <vincent.yang@xxxxxxxxxxxxxx>
+ * Copyright (C) 2014 Linaro Ltd Andy Green <andy.green@xxxxxxxxxx>
+ *
+ * This program is free software: you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation, version 2 of the License.
+ */
+
+#include <linux/err.h>
+#include <linux/delay.h>
+#include <linux/module.h>
+#include <linux/mmc/sd.h>
+#include <linux/mmc/host.h>
+#include <linux/mmc/card.h>
+#include <linux/gpio.h>
+#include <linux/of_gpio.h>
+#include <linux/of_address.h>
+#include <linux/platform_device.h>
+#include <linux/pm.h>
+#include <linux/pm_runtime.h>
+#include <linux/suspend.h>
+
+#include "sdhci.h"
+#include "sdhci-pltfm.h"
+#include "sdhci_f_sdh30.h"
+#include "../core/core.h"
+
+#define DRIVER_NAME "f_sdh30"
+
+
+struct f_sdhost_priv {
+ struct clk *clk_sd4;
+ struct clk *clk_b;
+ int gpio_select_1v8;
+ u32 vendor_hs200;
+ struct device *dev;
+};
+
+void sdhci_f_sdh30_soft_voltage_switch(struct sdhci_host *host)
+{
+ struct f_sdhost_priv *priv = sdhci_priv(host);
+ u32 ctrl = 0;
+
+ usleep_range(2500, 3000);
+ ctrl = sdhci_readl(host, F_SDH30_IO_CONTROL2);
+ ctrl |= F_SDH30_CRES_O_DN;
+ sdhci_writel(host, ctrl, F_SDH30_IO_CONTROL2);
+ ctrl |= F_SDH30_MSEL_O_1_8;
+ sdhci_writel(host, ctrl, F_SDH30_IO_CONTROL2);
+
+ if (gpio_is_valid(priv->gpio_select_1v8)) {
+ dev_info(priv->dev, "%s: setting gpio\n", __func__);
+ gpio_direction_output(priv->gpio_select_1v8, 0);
+ }
+
+ ctrl &= ~F_SDH30_CRES_O_DN;
+ sdhci_writel(host, ctrl, F_SDH30_IO_CONTROL2);
+ usleep_range(2500, 3000);
+
+ if (priv->vendor_hs200) {
+ dev_info(priv->dev, "%s: setting hs200\n", __func__);
+ ctrl = sdhci_readl(host, F_SDH30_ESD_CONTROL);
+ ctrl |= priv->vendor_hs200;
+ sdhci_writel(host, ctrl, F_SDH30_ESD_CONTROL);
+ }
+
+ ctrl = sdhci_readl(host, F_SDH30_TUNING_SETTING);
+ ctrl |= F_SDH30_CMD_CHK_DIS;
+ sdhci_writel(host, ctrl, F_SDH30_TUNING_SETTING);
+}
+
+unsigned int sdhci_f_sdh30_get_min_clock(struct sdhci_host *host)
+{
+ return F_SDH30_MIN_CLOCK;
+}
+
+void sdhci_f_sdh30_reset(struct sdhci_host *host, u8 mask)
+{
+ struct f_sdhost_priv *priv = sdhci_priv(host);
+
+ if (gpio_is_valid(priv->gpio_select_1v8))
+ gpio_direction_output(priv->gpio_select_1v8, 1);
+
+ if (sdhci_readw(host, SDHCI_CLOCK_CONTROL) == 0) {
+ sdhci_writew(host, 0xBC01, SDHCI_CLOCK_CONTROL);
+ mmiowb();
+ }
+
+ sdhci_reset(host, mask);
+}
+
+static const struct sdhci_ops sdhci_f_sdh30_ops = {
+ .voltage_switch = sdhci_f_sdh30_soft_voltage_switch,
+ .get_min_clock = sdhci_f_sdh30_get_min_clock,
+ .reset = sdhci_f_sdh30_reset,
+ .set_clock = sdhci_set_clock,
+ .set_bus_width = sdhci_set_bus_width,
+ .set_uhs_signaling = sdhci_set_uhs_signaling,
+};
+
+static int sdhci_f_sdh30_probe(struct platform_device *pdev)
+{
+ struct sdhci_host *host;
+ struct device *dev = &pdev->dev;
+ int irq, ctrl = 0, ret = 0;
+ struct f_sdhost_priv *priv;
+ u32 reg = 0, bus_width;
+
+ irq = platform_get_irq(pdev, 0);
+ if (irq < 0) {
+ dev_err(dev, "%s: no irq specified\n", __func__);
+ ret = irq;
+ goto err;
+ }
+
+ host = sdhci_alloc_host(dev, sizeof(struct sdhci_host) +
+ sizeof(struct f_sdhost_priv));
+ if (IS_ERR(host)) {
+ dev_err(dev, "%s: host allocate error\n", __func__);
+ ret = -ENOMEM;
+ goto err;
+ }
+ priv = sdhci_priv(host);
+ priv->dev = dev;
+
+ host->quirks = SDHCI_QUIRK_NO_ENDATTR_IN_NOPDESC |
+ SDHCI_QUIRK_INVERTED_WRITE_PROTECT;
+ host->quirks2 = SDHCI_QUIRK2_SUPPORT_SINGLE |
+ SDHCI_QUIRK2_VOLTAGE_SWITCH |
+ SDHCI_QUIRK2_TUNING_WORK_AROUND;
+
+ if (!of_property_read_u32(pdev->dev.of_node, "vendor-hs200",
+ &priv->vendor_hs200))
+ dev_info(dev, "Applying vendor-hs200 setting\n");
+ else
+ priv->vendor_hs200 = 0;
+
+ if (!of_property_read_u32(pdev->dev.of_node, "bus-width", &bus_width)) {
+ if (bus_width == 8) {
+ dev_info(dev, "Applying 8 bit bus width\n");
+ host->mmc->caps |= MMC_CAP_8_BIT_DATA;
+ }
+ }
+
+ ret = mmc_of_parse_voltage(pdev->dev.of_node, &host->ocr_mask);
+ if (ret) {
+ dev_err(dev, "%s: parse voltage error\n", __func__);
+ goto err_voltage;
+ }
+
+ host->hw_name = DRIVER_NAME;
+ host->ops = &sdhci_f_sdh30_ops;
+ host->irq = irq;
+
+ host->ioaddr = of_iomap(pdev->dev.of_node, 0);
+ if (!host->ioaddr) {
+ dev_err(dev, "%s: failed to remap registers\n", __func__);
+ ret = -ENXIO;
+ goto err_remap;
+ }
+
+ priv->clk_sd4 = of_clk_get(pdev->dev.of_node, 0);
+ if (!IS_ERR(priv->clk_sd4)) {
+ ret = clk_prepare_enable(priv->clk_sd4);
+ if (ret < 0) {
+ dev_err(dev, "Failed to enable sd4 clock: %d\n", ret);
+ goto err_clk1;
+ }
+ }
+ priv->clk_b = of_clk_get(pdev->dev.of_node, 1);
+ if (!IS_ERR(priv->clk_b)) {
+ ret = clk_prepare_enable(priv->clk_b);
+ if (ret < 0) {
+ dev_err(dev, "Failed to enable clk_b clock: %d\n", ret);
+ goto err_clk2;
+ }
+ }
+
+ /* optional */
+ priv->gpio_select_1v8 = of_get_gpio(pdev->dev.of_node, 0);
+ if (gpio_is_valid(priv->gpio_select_1v8)) {
+ ret = gpio_request(priv->gpio_select_1v8, "sdhci");
+ if (unlikely(ret)) {
+ dev_err(dev, " gpio %d request failed ",
+ priv->gpio_select_1v8);
+ goto err_gpio;
+ }
+ /* initially 3.3V */
+ ret = gpio_direction_output(priv->gpio_select_1v8, 1);
+ if (unlikely(ret)) {
+ dev_err(dev, "failed to set phy_enable gpio\n");
+ goto err_gpio;
+ }
+ }
+
+ ret = sdhci_add_host(host);
+ if (ret) {
+ dev_err(dev, "%s: host add error\n", __func__);
+ goto err_add_host;
+ }
+
+ platform_set_drvdata(pdev, host);
+
+#ifdef CONFIG_PM_RUNTIME
+ pm_runtime_enable(&pdev->dev);
+ ret = pm_runtime_get_sync(&pdev->dev);
+ if (ret < 0)
+ dev_err(dev, "Failed to pm_runtime_get_sync: %d\n", ret);
+#endif
+
+ /* init vendor specific regs */
+ ctrl = sdhci_readw(host, F_SDH30_AHB_CONFIG);
+ ctrl |= F_SDH30_SIN | F_SDH30_AHB_INCR_16 | F_SDH30_AHB_INCR_8 |
+ F_SDH30_AHB_INCR_4;
+ ctrl &= ~(F_SDH30_AHB_BIGED | F_SDH30_BUSLOCK_EN);
+ sdhci_writew(host, ctrl, F_SDH30_AHB_CONFIG);
+ mmiowb();
+
+ reg = sdhci_readl(host, F_SDH30_ESD_CONTROL);
+ sdhci_writel(host, reg & ~F_SDH30_EMMC_RST, F_SDH30_ESD_CONTROL);
+ msleep(20);
+ sdhci_writel(host, reg | F_SDH30_EMMC_RST, F_SDH30_ESD_CONTROL);
+ mmiowb();
+
+ return 0;
+
+err_add_host:
+ if (gpio_is_valid(priv->gpio_select_1v8)) {
+ gpio_direction_output(priv->gpio_select_1v8, 1);
+ gpio_free(priv->gpio_select_1v8);
+ }
+err_gpio:
+ clk_put(priv->clk_b);
+err_clk2:
+ clk_put(priv->clk_sd4);
+err_clk1:
+ iounmap(host->ioaddr);
+err_remap:
+err_voltage:
+ sdhci_free_host(host);
+err:
+ return ret;
+}
+
+static int sdhci_f_sdh30_remove(struct platform_device *pdev)
+{
+ struct sdhci_host *host = platform_get_drvdata(pdev);
+ struct f_sdhost_priv *priv = sdhci_priv(host);
+ struct resource *iomem = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+
+ sdhci_remove_host(host, readl(host->ioaddr + SDHCI_INT_STATUS) ==
+ 0xffffffff);
+ iounmap(host->ioaddr);
+ release_mem_region(iomem->start, resource_size(iomem));
+
+ clk_disable_unprepare(priv->clk_sd4);
+ clk_disable_unprepare(priv->clk_b);
+
+ clk_put(priv->clk_b);
+ clk_put(priv->clk_sd4);
+
+ if (gpio_is_valid(priv->gpio_select_1v8)) {
+ gpio_direction_output(priv->gpio_select_1v8, 1);
+ gpio_free(priv->gpio_select_1v8);
+ }
+
+ sdhci_free_host(host);
+ platform_set_drvdata(pdev, NULL);
+
+ return 0;
+}
+
+#ifdef CONFIG_PM_SLEEP
+static int sdhci_f_sdh30_suspend(struct device *dev)
+{
+ struct sdhci_host *host = dev_get_drvdata(dev);
+
+ return sdhci_suspend_host(host);
+}
+
+static int sdhci_f_sdh30_resume(struct device *dev)
+{
+ struct sdhci_host *host = dev_get_drvdata(dev);
+
+ return sdhci_resume_host(host);
+}
+#endif
+
+#ifdef CONFIG_PM_RUNTIME
+static int sdhci_f_sdh30_runtime_suspend(struct device *dev)
+{
+ struct sdhci_host *host = dev_get_drvdata(dev);
+
+ return sdhci_runtime_suspend_host(host);
+}
+
+static int sdhci_f_sdh30_runtime_resume(struct device *dev)
+{
+ struct sdhci_host *host = dev_get_drvdata(dev);
+
+ return sdhci_runtime_resume_host(host);
+}
+#endif
+
+#ifdef CONFIG_PM
+static const struct dev_pm_ops sdhci_f_sdh30_pmops = {
+ SET_SYSTEM_SLEEP_PM_OPS(sdhci_f_sdh30_suspend, sdhci_f_sdh30_resume)
+ SET_RUNTIME_PM_OPS(sdhci_f_sdh30_runtime_suspend,
+ sdhci_f_sdh30_runtime_resume, NULL)
+};
+
+#define SDHCI_F_SDH30_PMOPS (&sdhci_f_sdh30_pmops)
+
+#else
+#define SDHCI_F_SDH30_PMOPS NULL
+#endif
+
+static const struct of_device_id f_sdh30_dt_ids[] = {
+ { .compatible = "fujitsu,f_sdh30" },
+ { /* sentinel */ }
+};
+MODULE_DEVICE_TABLE(of, f_sdh30_dt_ids);
+
+static struct platform_driver sdhci_f_sdh30_driver = {
+ .driver = {
+ .name = DRIVER_NAME,
+ .owner = THIS_MODULE,
+ .of_match_table = f_sdh30_dt_ids,
+#ifdef CONFIG_PM_SLEEP
+ .pm = SDHCI_F_SDH30_PMOPS,
+#endif
+ },
+ .probe = sdhci_f_sdh30_probe,
+ .remove = sdhci_f_sdh30_remove,
+};
+
+module_platform_driver(sdhci_f_sdh30_driver);
+
+MODULE_DESCRIPTION("F_SDH30 SD Card Controller driver");
+MODULE_LICENSE("GPL v2");
+MODULE_AUTHOR("FUJITSU SEMICONDUCTOR LTD.");
+MODULE_ALIAS("platform: " DRIVER_NAME);
diff --git a/drivers/mmc/host/sdhci_f_sdh30.h b/drivers/mmc/host/sdhci_f_sdh30.h
new file mode 100644
index 0000000..50c51c9
--- /dev/null
+++ b/drivers/mmc/host/sdhci_f_sdh30.h
@@ -0,0 +1,40 @@
+/*
+ * linux/drivers/mmc/host/sdhci_f_sdh30.h
+ *
+ * Copyright (C) 2013 - 2014 Fujitsu Semiconductor, Ltd
+ * Vincent Yang <vincent.yang@xxxxxxxxxxxxxx>
+ * Copyright (C) 2014 Linaro Ltd Andy Green <andy.green@xxxxxxxxxx>
+ *
+ * This program is free software: you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation, version 2 of the License.
+ */
+
+#ifndef F_SDH30_H
+#define F_SDH30_H
+
+/* F_SDH30 extended Controller registers */
+#define F_SDH30_AHB_CONFIG 0x100
+#define F_SDH30_AHB_BIGED 0x00000040
+#define F_SDH30_BUSLOCK_DMA 0x00000020
+#define F_SDH30_BUSLOCK_EN 0x00000010
+#define F_SDH30_SIN 0x00000008
+#define F_SDH30_AHB_INCR_16 0x00000004
+#define F_SDH30_AHB_INCR_8 0x00000002
+#define F_SDH30_AHB_INCR_4 0x00000001
+
+#define F_SDH30_TUNING_SETTING 0x108
+#define F_SDH30_CMD_CHK_DIS 0x00010000
+
+#define F_SDH30_IO_CONTROL2 0x114
+#define F_SDH30_CRES_O_DN 0x00080000
+#define F_SDH30_MSEL_O_1_8 0x00040000
+
+#define F_SDH30_ESD_CONTROL 0x124
+#define F_SDH30_EMMC_RST 0x00000002
+
+#define F_SDH30_CMD_DAT_DELAY 0x200
+
+#define F_SDH30_MIN_CLOCK 400000
+
+#endif
--
1.9.0
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
