[PATCH 1/2] net: phy: micrel: add LED control on KSZ9131

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



Add the possibility to read the LED configuration via DTS properties from
KSZ9131 PHY node. Add the new proprties and handle for them:
micrel,led-mode-behavior
micrel,led-mode-select

Signed-off-by: Ivan Mikhaylov <i.mikhaylov@xxxxxxxxx>
---
 drivers/net/phy/micrel.c | 69 +++++++++++++++++++++++++++++++++++++++-
 1 file changed, 68 insertions(+), 1 deletion(-)

diff --git a/drivers/net/phy/micrel.c b/drivers/net/phy/micrel.c
index 3fe552675dd2..117f3a3b9dd6 100644
--- a/drivers/net/phy/micrel.c
+++ b/drivers/net/phy/micrel.c
@@ -71,6 +71,11 @@
 #define MII_KSZPHY_RX_DATA_PAD_SKEW             0x105
 #define MII_KSZPHY_TX_DATA_PAD_SKEW             0x106
 
+/* KSZ9131 LED registers */
+#define MII_KSZPHY_LED_MODE_SELECT		0x16
+#define MII_KSZPHY_LED_BEHAVIOR			0x17
+#define MII_KSZPHY_LED_MODE			0x1a
+
 #define PS_TO_REG				200
 
 struct kszphy_hw_stat {
@@ -86,6 +91,8 @@ static struct kszphy_hw_stat kszphy_hw_stats[] = {
 
 struct kszphy_type {
 	u32 led_mode_reg;
+	u32 led_mode_behavior_reg;
+	u32 led_mode_select_reg;
 	u16 interrupt_level_mask;
 	bool has_broadcast_disable;
 	bool has_nand_tree_disable;
@@ -95,6 +102,8 @@ struct kszphy_type {
 struct kszphy_priv {
 	const struct kszphy_type *type;
 	int led_mode;
+	int led_mode_behavior;
+	int led_mode_select;
 	bool rmii_ref_clk_sel;
 	bool rmii_ref_clk_sel_val;
 	u64 stats[ARRAY_SIZE(kszphy_hw_stats)];
@@ -131,6 +140,13 @@ static const struct kszphy_type ksz9021_type = {
 	.interrupt_level_mask	= BIT(14),
 };
 
+static const struct kszphy_type ksz9131_type = {
+	.led_mode_reg		= MII_KSZPHY_LED_MODE,
+	.led_mode_behavior_reg	= MII_KSZPHY_LED_BEHAVIOR,
+	.led_mode_select_reg	= MII_KSZPHY_LED_MODE_SELECT,
+	.interrupt_level_mask	= BIT(14),
+};
+
 static int kszphy_extended_write(struct phy_device *phydev,
 				u32 regnum, u16 val)
 {
@@ -204,6 +220,7 @@ static int kszphy_setup_led(struct phy_device *phydev, u32 reg, int val)
 
 	switch (reg) {
 	case MII_KSZPHY_CTRL_1:
+	case MII_KSZPHY_LED_MODE:
 		shift = 14;
 		break;
 	case MII_KSZPHY_CTRL_2:
@@ -286,6 +303,26 @@ static int kszphy_config_reset(struct phy_device *phydev)
 	if (priv->led_mode >= 0)
 		kszphy_setup_led(phydev, priv->type->led_mode_reg, priv->led_mode);
 
+	if (priv->led_mode_behavior >= 0) {
+		ret = phy_write(phydev, priv->type->led_mode_behavior_reg,
+				priv->led_mode_behavior);
+		if (ret) {
+			phydev_err(phydev,
+				   "failed to set led mode behavior reg\n");
+			return ret;
+		}
+	}
+
+	if (priv->led_mode_select >= 0) {
+		ret = phy_write(phydev, priv->type->led_mode_select_reg,
+				priv->led_mode_select);
+		if (ret) {
+			phydev_err(phydev,
+				   "failed to set led mode select reg\n");
+			return ret;
+		}
+	}
+
 	return 0;
 }
 
@@ -1122,6 +1159,36 @@ static int kszphy_probe(struct phy_device *phydev)
 		priv->led_mode = -1;
 	}
 
+	if (type->led_mode_behavior_reg) {
+		ret = of_property_read_u32(np, "micrel,led-mode-behavior",
+					   &priv->led_mode_behavior);
+		if (!ret) {
+			ret = phy_write(phydev, type->led_mode_behavior_reg,
+					priv->led_mode_behavior);
+			if (ret)
+				phydev_err(phydev,
+					   "invalid led mode behavior: 0x%x\n",
+					   priv->led_mode_behavior);
+		}
+	} else {
+		priv->led_mode_behavior = -1;
+	}
+
+	if (type->led_mode_select_reg) {
+		ret = of_property_read_u32(np, "micrel,led-mode-select",
+					   &priv->led_mode_select);
+		if (!ret) {
+			ret = phy_write(phydev, type->led_mode_select_reg,
+					priv->led_mode_select);
+			if (ret)
+				phydev_err(phydev,
+					   "invalid led mode select: 0x%x\n",
+					   priv->led_mode_select);
+		}
+	} else {
+		priv->led_mode_select = -1;
+	}
+
 	clk = devm_clk_get(&phydev->mdio.dev, "rmii-ref");
 	/* NOTE: clk may be NULL if building without CONFIG_HAVE_CLK */
 	if (!IS_ERR_OR_NULL(clk)) {
@@ -1319,7 +1386,7 @@ static struct phy_driver ksphy_driver[] = {
 	.phy_id_mask	= MICREL_PHY_ID_MASK,
 	.name		= "Microchip KSZ9131 Gigabit PHY",
 	/* PHY_GBIT_FEATURES */
-	.driver_data	= &ksz9021_type,
+	.driver_data	= &ksz9131_type,
 	.probe		= kszphy_probe,
 	.config_init	= ksz9131_config_init,
 	.read_status	= genphy_read_status,
-- 
2.21.1




[Index of Archives]     [Device Tree Compilter]     [Device Tree Spec]     [Linux Driver Backports]     [Video for Linux]     [Linux USB Devel]     [Linux PCI Devel]     [Linux Audio Users]     [Linux Kernel]     [Linux SCSI]     [XFree86]     [Yosemite Backpacking]


  Powered by Linux