Re: [PATCH v1 4/9] pinctrl: tegra-xusb: Add USB PHY support

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 




On Wed, Jun 25, 2014 at 3:12 PM, Stephen Warren <swarren@xxxxxxxxxxxxx> wrote:
> On 06/18/2014 12:16 AM, Andrew Bresticker wrote:
>> In addition to the PCIe and SATA PHYs, the XUSB pad controller also
>> supports 3 UTMI, 2 HSIC, and 2 USB3 PHYs.  Each USB3 PHY uses a single
>> PCIe or SATA lane and is mapped to one of the three UTMI ports.
>>
>
>> diff --git a/drivers/pinctrl/pinctrl-tegra-xusb.c b/drivers/pinctrl/pinctrl-tegra-xusb.c
>
>> @@ -372,6 +720,193 @@ static int tegra_xusb_padctl_pinconf_group_set(struct pinctrl_dev *pinctrl,
>>                       padctl_writel(padctl, regval, lane->offset);
>>                       break;
>>
>> +             case TEGRA_XUSB_PADCTL_USB3_PORT_NUM:
>> +                     if (value >= TEGRA_XUSB_PADCTL_USB3_PORTS) {
>> +                             dev_err(padctl->dev, "Invalid USB3 port: %lu\n",
>> +                                     value);
>> +                             return -EINVAL;
>> +                     }
>> +                     if (!is_pcie_sata_lane(group)) {
>> +                             dev_err(padctl->dev,
>> +                                     "USB3 port not applicable for pin %d\n",
>> +                                     group);
>> +                             return -EINVAL;
>> +                     }
>> +                     padctl->usb3_ports[value].lane = group;
>> +                     break;
>
> It feels odd to use pinctrl for a SW-only purpose. In other words, that
> chunk of code isn't writing the pinconf data to HW, but rather some
> internal variable.

Well the mapping of lanes to USB3 ports is a hardware property and we
do use it when programming the hardware later to choose which set of
lane registers to program given a USB3 port, but it's true that it's
not some value we program into HW directly.

> Perhaps it would make more sense for the DT binding to represent this
> data directly in a custom property that's parsed at probe() time. That
> way, pinctrl only touches "real" HW stuff.

I'm on the fence about this.  If you or others feel strongly about
this then I can make it a separate DT property and move it out of the
pinctrl properties.

>> +static int usb3_phy_power_on(struct phy *phy)
>> +{
>> +     struct tegra_xusb_padctl *padctl = phy_get_drvdata(phy);
>> +     int port = usb3_phy_to_port(phy);
>> +     int lane = padctl->usb3_ports[port].lane;
>> +     u32 value, offset;
>> +
>> +     value = padctl_readl(padctl, XUSB_PADCTL_IOPHY_USB3_PADX_CTL2(port));
>> +     value &= ~((XUSB_PADCTL_IOPHY_USB3_PAD_CTL2_RX_WANDER_MASK <<
>> +                 XUSB_PADCTL_IOPHY_USB3_PAD_CTL2_RX_WANDER_SHIFT) |
>> +                (XUSB_PADCTL_IOPHY_USB3_PAD_CTL2_RX_EQ_MASK <<
>> +                 XUSB_PADCTL_IOPHY_USB3_PAD_CTL2_RX_EQ_SHIFT) |
>> +                (XUSB_PADCTL_IOPHY_USB3_PAD_CTL2_CDR_CNTL_MASK <<
>> +                 XUSB_PADCTL_IOPHY_USB3_PAD_CTL2_CDR_CNTL_SHIFT));
>
> Hmm. So there is a lot of "PHY" stuff here after all.
>
> However, the PHYs implemented here appear to implement very low-level
> I/O pad code, whereas the PHYs we have for our USB 2.0 controller are
> somewhat higher-level; they're more USB-oriented than just IO pad
> oriented. Do you know which level of abstraction a Linux PHY object is
> supposed to be? I could never get an answer when I asked before.

The only other PHY driver I've worked with (Exynos USB2/3 PHYs) also
mainly only did low-level pad control stuff, but looking at a couple
of other USB PHYs (MSM, MV), there appear to be others that have
higher-level USB stuff in the PHY driver.  Perhaps Kishon or Felipe
could offer us some guidance?
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at  http://vger.kernel.org/majordomo-info.html




[Index of Archives]     [Device Tree Compilter]     [Device Tree Spec]     [Linux Driver Backports]     [Video for Linux]     [Linux USB Devel]     [Linux PCI Devel]     [Linux Audio Users]     [Linux Kernel]     [Linux SCSI]     [XFree86]     [Yosemite Backpacking]
  Powered by Linux