Add initial support for phyBOARD-Pollux-i.MX8MP.
Supported basic features:
* eMMC
* i2c EEPROM
* i2c RTC
* i2c LED
* PMIC
* debug UART
* SD card
* 1Gbit Ethernet (fec)
* watchdog
Signed-off-by: Teresa Remmet <t.remmet@xxxxxxxxx>
---
arch/arm64/boot/dts/freescale/Makefile | 1 +
.../dts/freescale/imx8mp-phyboard-pollux-rdk.dts | 166 ++++++++++++
.../boot/dts/freescale/imx8mp-phycore-som.dtsi | 296 +++++++++++++++++++++
3 files changed, 463 insertions(+)
create mode 100644 arch/arm64/boot/dts/freescale/imx8mp-phyboard-pollux-rdk.dts
create mode 100644 arch/arm64/boot/dts/freescale/imx8mp-phycore-som.dtsi
diff --git a/arch/arm64/boot/dts/freescale/Makefile b/arch/arm64/boot/dts/freescale/Makefile
index acfb8af45912..a43b496678be 100644
--- a/arch/arm64/boot/dts/freescale/Makefile
+++ b/arch/arm64/boot/dts/freescale/Makefile
@@ -37,6 +37,7 @@ dtb-$(CONFIG_ARCH_MXC) += imx8mn-evk.dtb
dtb-$(CONFIG_ARCH_MXC) += imx8mn-ddr4-evk.dtb
dtb-$(CONFIG_ARCH_MXC) += imx8mn-var-som-symphony.dtb
dtb-$(CONFIG_ARCH_MXC) += imx8mp-evk.dtb
+dtb-$(CONFIG_ARCH_MXC) += imx8mp-phyboard-pollux-rdk.dtb
dtb-$(CONFIG_ARCH_MXC) += imx8mq-evk.dtb
dtb-$(CONFIG_ARCH_MXC) += imx8mq-hummingboard-pulse.dtb
dtb-$(CONFIG_ARCH_MXC) += imx8mq-librem5-devkit.dtb
diff --git a/arch/arm64/boot/dts/freescale/imx8mp-phyboard-pollux-rdk.dts b/arch/arm64/boot/dts/freescale/imx8mp-phyboard-pollux-rdk.dts
new file mode 100644
index 000000000000..9a3d73f08429
--- /dev/null
+++ b/arch/arm64/boot/dts/freescale/imx8mp-phyboard-pollux-rdk.dts
@@ -0,0 +1,166 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Copyright (C) 2020 PHYTEC Messtechnik GmbH
+ * Author: Teresa Remmet <t.remmet@xxxxxxxxx>
+ */
+
+/dts-v1/;
+
+#include <dt-bindings/leds/leds-pca9532.h>
+#include <dt-bindings/pwm/pwm.h>
+#include "imx8mp-phycore-som.dtsi"
+
+/ {
+ model = "PHYTEC phyBOARD-Pollux i.MX8MP";
+ compatible = "phytec,imx8mp-phyboard-pollux-rdk",
+ "phytec,imx8mp-phycore-som", "fsl,imx8mp";
+
+ chosen {
+ stdout-path = &uart2;
+ };
+
+ reg_usdhc2_vmmc: regulator-usdhc2 {
+ compatible = "regulator-fixed";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_reg_usdhc2_vmmc>;
+ regulator-name = "VSD_3V3";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ gpio = <&gpio2 19 GPIO_ACTIVE_HIGH>;
+ enable-active-high;
+ startup-delay-us = <100>;
+ off-on-delay-us = <12000>;
+ };
+};
+
+&i2c2 {
+ clock-frequency = <400000>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_i2c2>;
+ pinctrl-1 = <&pinctrl_i2c2_gpio>;
+ sda-gpios = <&gpio5 17 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
+ scl-gpios = <&gpio5 16 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
+ status = "okay";
+
+ eeprom@51 {
+ compatible = "atmel,24c02";
+ reg = <0x51>;
+ pagesize = <16>;
+ status = "okay";
+ };
+
+ leds@62 {
+ compatible = "nxp,pca9533";
+ reg = <0x62>;
+ status = "okay";
+
+ led1 {
+ label = "red:user1";
+ type = <PCA9532_TYPE_LED>;
+ };
+
+ led2 {
+ label = "green:user2";
+ type = <PCA9532_TYPE_LED>;
+ };
+
+ led3 {
+ label = "blue:user3";
+ type = <PCA9532_TYPE_LED>;
+ };
+ };
+};
+
+&snvs_pwrkey {
+ status = "okay";
+};
+
+/* debug console */
+&uart2 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_uart2>;
+ status = "okay";
+};
+
+/* SD-Card */
+&usdhc2 {
+ pinctrl-names = "default", "state_100mhz", "state_200mhz";
+ pinctrl-0 = <&pinctrl_usdhc2>, <&pinctrl_usdhc2_pins>;
+ pinctrl-1 = <&pinctrl_usdhc2_100mhz>, <&pinctrl_usdhc2_pins>;
+ pinctrl-2 = <&pinctrl_usdhc2_200mhz>, <&pinctrl_usdhc2_pins>;
+ cd-gpios = <&gpio2 12 GPIO_ACTIVE_LOW>;
+ vmmc-supply = <®_usdhc2_vmmc>;
+ bus-width = <4>;
+ status = "okay";
+};
+
+&iomuxc {
+ pinctrl_i2c2: i2c2grp {
+ fsl,pins = <
+ MX8MP_IOMUXC_I2C2_SCL__I2C2_SCL 0x400001c3
+ MX8MP_IOMUXC_I2C2_SDA__I2C2_SDA 0x400001c3
+ >;
+ };
+
+ pinctrl_i2c2_gpio: i2c2gpiogrp {
+ fsl,pins = <
+ MX8MP_IOMUXC_I2C2_SCL__GPIO5_IO16 0x1e3
+ MX8MP_IOMUXC_I2C2_SDA__GPIO5_IO17 0x1e3
+ >;
+ };
+
+ pinctrl_reg_usdhc2_vmmc: regusdhc2vmmcgrp {
+ fsl,pins = <
+ MX8MP_IOMUXC_SD2_RESET_B__GPIO2_IO19 0x41
+ >;
+ };
+
+ pinctrl_uart2: uart2grp {
+ fsl,pins = <
+ MX8MP_IOMUXC_UART2_RXD__UART2_DCE_RX 0x49
+ MX8MP_IOMUXC_UART2_TXD__UART2_DCE_TX 0x49
+ >;
+ };
+
+ pinctrl_usdhc2_pins: usdhc2-gpiogrp {
+ fsl,pins = <
+ MX8MP_IOMUXC_SD2_CD_B__GPIO2_IO12 0x1c4
+ >;
+ };
+
+ pinctrl_usdhc2: usdhc2grp {
+ fsl,pins = <
+ MX8MP_IOMUXC_SD2_CLK__USDHC2_CLK 0x190
+ MX8MP_IOMUXC_SD2_CMD__USDHC2_CMD 0x1d0
+ MX8MP_IOMUXC_SD2_DATA0__USDHC2_DATA0 0x1d0
+ MX8MP_IOMUXC_SD2_DATA1__USDHC2_DATA1 0x1d0
+ MX8MP_IOMUXC_SD2_DATA2__USDHC2_DATA2 0x1d0
+ MX8MP_IOMUXC_SD2_DATA3__USDHC2_DATA3 0x1d0
+ MX8MP_IOMUXC_GPIO1_IO04__USDHC2_VSELECT 0xc1
+ >;
+ };
+
+ pinctrl_usdhc2_100mhz: usdhc2-100mhzgrp {
+ fsl,pins = <
+ MX8MP_IOMUXC_SD2_CLK__USDHC2_CLK 0x194
+ MX8MP_IOMUXC_SD2_CMD__USDHC2_CMD 0x1d4
+ MX8MP_IOMUXC_SD2_DATA0__USDHC2_DATA0 0x1d4
+ MX8MP_IOMUXC_SD2_DATA1__USDHC2_DATA1 0x1d4
+ MX8MP_IOMUXC_SD2_DATA2__USDHC2_DATA2 0x1d4
+ MX8MP_IOMUXC_SD2_DATA3__USDHC2_DATA3 0x1d4
+ MX8MP_IOMUXC_GPIO1_IO04__USDHC2_VSELECT 0xc1
+ >;
+ };
+
+ pinctrl_usdhc2_200mhz: usdhc2-200mhzgrp {
+ fsl,pins = <
+ MX8MP_IOMUXC_SD2_CLK__USDHC2_CLK 0x196
+ MX8MP_IOMUXC_SD2_CMD__USDHC2_CMD 0x1d6
+ MX8MP_IOMUXC_SD2_DATA0__USDHC2_DATA0 0x1d6
+ MX8MP_IOMUXC_SD2_DATA1__USDHC2_DATA1 0x1d6
+ MX8MP_IOMUXC_SD2_DATA2__USDHC2_DATA2 0x1d6
+ MX8MP_IOMUXC_SD2_DATA3__USDHC2_DATA3 0x1d6
+ MX8MP_IOMUXC_GPIO1_IO04__USDHC2_VSELECT 0xc1
+ >;
+ };
+};
diff --git a/arch/arm64/boot/dts/freescale/imx8mp-phycore-som.dtsi b/arch/arm64/boot/dts/freescale/imx8mp-phycore-som.dtsi
new file mode 100644
index 000000000000..8618df68b1e5
--- /dev/null
+++ b/arch/arm64/boot/dts/freescale/imx8mp-phycore-som.dtsi
@@ -0,0 +1,296 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Copyright (C) 2020 PHYTEC Messtechnik GmbH
+ * Author: Teresa Remmet <t.remmet@xxxxxxxxx>
+ */
+
+#include <dt-bindings/net/ti-dp83867.h>
+#include "imx8mp.dtsi"
+
+/ {
+ model = "PHYTEC phyCORE-i.MX8MP";
+ compatible = "phytec,imx8mp-phycore-som", "fsl,imx8mp";
+
+ aliases {
+ rtc0 = &rv3028;
+ rtc1 = &snvs_rtc;
+ };
+
+ memory@40000000 {
+ device_type = "memory";
+ reg = <0x0 0x40000000 0 0x80000000>;
+ };
+};
+
+&A53_0 {
+ cpu-supply = <&buck2>;
+};
+
+&A53_1 {
+ cpu-supply = <&buck2>;
+};
+
+&A53_2 {
+ cpu-supply = <&buck2>;
+};
+
+&A53_3 {
+ cpu-supply = <&buck2>;
+};
+
+/* ethernet 1 */
+&fec {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_fec>;
+ phy-mode = "rgmii-id";
+ phy-handle = <ðphy1>;
+ fsl,magic-packet;
+ status = "okay";
+
+ mdio {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ ethphy1: ethernet-phy@0 {
+ compatible = "ethernet-phy-ieee802.3-c22";
+ reg = <0>;
+ interrupt-parent = <&gpio1>;
+ interrupts = <15 IRQ_TYPE_EDGE_FALLING>;
+ ti,rx-internal-delay = <DP83867_RGMIIDCTL_2_00_NS>;
+ ti,tx-internal-delay = <DP83867_RGMIIDCTL_2_00_NS>;
+ ti,fifo-depth = <DP83867_PHYCR_FIFO_DEPTH_4_B_NIB>;
+ ti,clk-output-sel = <DP83867_CLK_O_SEL_OFF>;
+ enet-phy-lane-no-swap;
+ };
+ };
+};
+
+&i2c1 {
+ clock-frequency = <400000>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_i2c1>;
+ pinctrl-1 = <&pinctrl_i2c1_gpio>;
+ sda-gpios = <&gpio5 15 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
+ scl-gpios = <&gpio5 14 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
+ status = "okay";
+
+ pmic: pmic@25 {
+ reg = <0x25>;
+ compatible = "nxp,pca9450c";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_pmic>;
+ interrupt-parent = <&gpio4>;
+ interrupts = <18 IRQ_TYPE_LEVEL_LOW>;
+
+ regulators {
+ buck1: BUCK1 {
+ regulator-compatible = "BUCK1";
+ regulator-min-microvolt = <600000>;
+ regulator-max-microvolt = <2187500>;
+ regulator-boot-on;
+ regulator-always-on;
+ regulator-ramp-delay = <3125>;
+ };
+
+ buck2: BUCK2 {
+ regulator-compatible = "BUCK2";
+ regulator-min-microvolt = <600000>;
+ regulator-max-microvolt = <2187500>;
+ regulator-boot-on;
+ regulator-always-on;
+ regulator-ramp-delay = <3125>;
+ };
+
+ buck4: BUCK4 {
+ regulator-compatible = "BUCK4";
+ regulator-min-microvolt = <600000>;
+ regulator-max-microvolt = <3400000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ buck5: BUCK5 {
+ regulator-compatible = "BUCK5";
+ regulator-min-microvolt = <600000>;
+ regulator-max-microvolt = <3400000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ buck6: BUCK6 {
+ regulator-compatible = "BUCK6";
+ regulator-min-microvolt = <600000>;
+ regulator-max-microvolt = <3400000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ ldo1: LDO1 {
+ regulator-compatible = "LDO1";
+ regulator-min-microvolt = <1600000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ ldo2: LDO2 {
+ regulator-compatible = "LDO2";
+ regulator-min-microvolt = <800000>;
+ regulator-max-microvolt = <1150000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ ldo3: LDO3 {
+ regulator-compatible = "LDO3";
+ regulator-min-microvolt = <800000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ ldo4: LDO4 {
+ regulator-compatible = "LDO4";
+ regulator-min-microvolt = <800000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ ldo5: LDO5 {
+ regulator-compatible = "LDO5";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <3300000>;
+ };
+ };
+ };
+
+ eeprom@51 {
+ compatible = "atmel,24c32";
+ reg = <0x51>;
+ pagesize = <32>;
+ status = "okay";
+ };
+
+ rv3028: rtc@52 {
+ compatible = "microcrystal,rv3028";
+ reg = <0x52>;
+ trickle-resistor-ohms = <1000>;
+ enable-level-switching-mode;
+ status = "okay";
+ };
+};
+
+/* eMMC */
+&usdhc3 {
+ pinctrl-names = "default", "state_100mhz", "state_200mhz";
+ pinctrl-0 = <&pinctrl_usdhc3>;
+ pinctrl-1 = <&pinctrl_usdhc3_100mhz>;
+ pinctrl-2 = <&pinctrl_usdhc3_200mhz>;
+ bus-width = <8>;
+ non-removable;
+ status = "okay";
+};
+
+&wdog1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_wdog>;
+ fsl,ext-reset-output;
+ status = "okay";
+};
+
+&iomuxc {
+ pinctrl_fec: fecgrp {
+ fsl,pins = <
+ MX8MP_IOMUXC_SAI1_RXD2__ENET1_MDC 0x3
+ MX8MP_IOMUXC_SAI1_RXD3__ENET1_MDIO 0x3
+ MX8MP_IOMUXC_SAI1_RXD4__ENET1_RGMII_RD0 0x91
+ MX8MP_IOMUXC_SAI1_RXD5__ENET1_RGMII_RD1 0x91
+ MX8MP_IOMUXC_SAI1_RXD6__ENET1_RGMII_RD2 0x91
+ MX8MP_IOMUXC_SAI1_RXD7__ENET1_RGMII_RD3 0x91
+ MX8MP_IOMUXC_SAI1_TXC__ENET1_RGMII_RXC 0x91
+ MX8MP_IOMUXC_SAI1_TXFS__ENET1_RGMII_RX_CTL 0x91
+ MX8MP_IOMUXC_SAI1_TXD0__ENET1_RGMII_TD0 0x1f
+ MX8MP_IOMUXC_SAI1_TXD1__ENET1_RGMII_TD1 0x1f
+ MX8MP_IOMUXC_SAI1_TXD2__ENET1_RGMII_TD2 0x1f
+ MX8MP_IOMUXC_SAI1_TXD3__ENET1_RGMII_TD3 0x1f
+ MX8MP_IOMUXC_SAI1_TXD4__ENET1_RGMII_TX_CTL 0x1f
+ MX8MP_IOMUXC_SAI1_TXD5__ENET1_RGMII_TXC 0x1f
+ MX8MP_IOMUXC_GPIO1_IO15__GPIO1_IO15 0x11
+ >;
+ };
+
+ pinctrl_i2c1: i2c1grp {
+ fsl,pins = <
+ MX8MP_IOMUXC_I2C1_SCL__I2C1_SCL 0x400001c3
+ MX8MP_IOMUXC_I2C1_SDA__I2C1_SDA 0x400001c3
+ >;
+ };
+
+ pinctrl_i2c1_gpio: i2c1gpiogrp {
+ fsl,pins = <
+ MX8MP_IOMUXC_I2C1_SCL__GPIO5_IO14 0x1e3
+ MX8MP_IOMUXC_I2C1_SDA__GPIO5_IO15 0x1e3
+ >;
+ };
+
+ pinctrl_pmic: pmicirqgrp {
+ fsl,pins = <
+ MX8MP_IOMUXC_SAI1_TXD6__GPIO4_IO18 0x141
+ >;
+ };
+
+ pinctrl_usdhc3: usdhc3grp {
+ fsl,pins = <
+ MX8MP_IOMUXC_NAND_WE_B__USDHC3_CLK 0x190
+ MX8MP_IOMUXC_NAND_WP_B__USDHC3_CMD 0x1d0
+ MX8MP_IOMUXC_NAND_DATA04__USDHC3_DATA0 0x1d0
+ MX8MP_IOMUXC_NAND_DATA05__USDHC3_DATA1 0x1d0
+ MX8MP_IOMUXC_NAND_DATA06__USDHC3_DATA2 0x1d0
+ MX8MP_IOMUXC_NAND_DATA07__USDHC3_DATA3 0x1d0
+ MX8MP_IOMUXC_NAND_RE_B__USDHC3_DATA4 0x1d0
+ MX8MP_IOMUXC_NAND_CE2_B__USDHC3_DATA5 0x1d0
+ MX8MP_IOMUXC_NAND_CE3_B__USDHC3_DATA6 0x1d0
+ MX8MP_IOMUXC_NAND_CLE__USDHC3_DATA7 0x1d0
+ MX8MP_IOMUXC_NAND_CE1_B__USDHC3_STROBE 0x190
+ >;
+ };
+
+ pinctrl_usdhc3_100mhz: usdhc3-100mhzgrp {
+ fsl,pins = <
+ MX8MP_IOMUXC_NAND_WE_B__USDHC3_CLK 0x194
+ MX8MP_IOMUXC_NAND_WP_B__USDHC3_CMD 0x1d4
+ MX8MP_IOMUXC_NAND_DATA04__USDHC3_DATA0 0x1d4
+ MX8MP_IOMUXC_NAND_DATA05__USDHC3_DATA1 0x1d4
+ MX8MP_IOMUXC_NAND_DATA06__USDHC3_DATA2 0x1d4
+ MX8MP_IOMUXC_NAND_DATA07__USDHC3_DATA3 0x1d4
+ MX8MP_IOMUXC_NAND_RE_B__USDHC3_DATA4 0x1d4
+ MX8MP_IOMUXC_NAND_CE2_B__USDHC3_DATA5 0x1d4
+ MX8MP_IOMUXC_NAND_CE3_B__USDHC3_DATA6 0x1d4
+ MX8MP_IOMUXC_NAND_CLE__USDHC3_DATA7 0x1d4
+ MX8MP_IOMUXC_NAND_CE1_B__USDHC3_STROBE 0x194
+ >;
+ };
+
+ pinctrl_usdhc3_200mhz: usdhc3-200mhzgrp {
+ fsl,pins = <
+ MX8MP_IOMUXC_NAND_WE_B__USDHC3_CLK 0x196
+ MX8MP_IOMUXC_NAND_WP_B__USDHC3_CMD 0x1d6
+ MX8MP_IOMUXC_NAND_DATA04__USDHC3_DATA0 0x1d6
+ MX8MP_IOMUXC_NAND_DATA05__USDHC3_DATA1 0x1d6
+ MX8MP_IOMUXC_NAND_DATA06__USDHC3_DATA2 0x1d6
+ MX8MP_IOMUXC_NAND_DATA07__USDHC3_DATA3 0x1d6
+ MX8MP_IOMUXC_NAND_RE_B__USDHC3_DATA4 0x1d6
+ MX8MP_IOMUXC_NAND_CE2_B__USDHC3_DATA5 0x1d6
+ MX8MP_IOMUXC_NAND_CE3_B__USDHC3_DATA6 0x1d6
+ MX8MP_IOMUXC_NAND_CLE__USDHC3_DATA7 0x1d6
+ MX8MP_IOMUXC_NAND_CE1_B__USDHC3_STROBE 0x196
+ >;
+ };
+
+ pinctrl_wdog: wdoggrp {
+ fsl,pins = <
+ MX8MP_IOMUXC_GPIO1_IO02__WDOG1_WDOG_B 0xc6
+ >;
+ };
+};
--
2.7.4
