On Sun, Nov 29, 2020 at 08:35:32PM +0200, Cristian Ciocaltea wrote:
> On Sat, Nov 28, 2020 at 01:08:51PM +0530, Manivannan Sadhasivam wrote:
> > On Fri, Nov 20, 2020 at 01:56:10AM +0200, Cristian Ciocaltea wrote:
> > > Add uSD support for RoseapplePi SBC using a fixed regulator as a
> > > temporary solution until PMIC support becomes available.
> > >
> > > Signed-off-by: Cristian Ciocaltea <cristian.ciocaltea@xxxxxxxxx>
> > > ---
> > > arch/arm/boot/dts/owl-s500-roseapplepi.dts | 50 ++++++++++++++++++++++
> > > 1 file changed, 50 insertions(+)
> > >
> > > diff --git a/arch/arm/boot/dts/owl-s500-roseapplepi.dts b/arch/arm/boot/dts/owl-s500-roseapplepi.dts
> > > index 800edf5d2d12..fe9ae3619422 100644
> > > --- a/arch/arm/boot/dts/owl-s500-roseapplepi.dts
> > > +++ b/arch/arm/boot/dts/owl-s500-roseapplepi.dts
> > > @@ -14,6 +14,7 @@ / {
> > > model = "Roseapple Pi";
> > >
> > > aliases {
> > > + mmc0 = &mmc0;
> > > serial2 = &uart2;
> > > };
> > >
> > > @@ -25,6 +26,55 @@ memory@0 {
> > > device_type = "memory";
> > > reg = <0x0 0x80000000>; /* 2GB */
> > > };
> > > +
> > > + /* Fixed regulator used in the absence of PMIC */
> > > + sd_vcc: sd-vcc {
> >
> > Is this the exact name in the schematics?
>
> Yes, it is referred as "SD_VCC". Once the support for the ATC260x PMIC
> will be available, the following item will be present in the regulators
> list:
>
> sd_vcc: switchldo1 {
> regulator-name = "SD_VCC";
> regulator-min-microvolt = <3000000>;
> regulator-max-microvolt = <3300000>;
> regulator-always-on;
> regulator-boot-on;
> };
okay, looks fine to me.
Thanks,
Mani
>
> Thanks,
> Cristi
>
> > Thanks,
> > Mani
> >
> > > + compatible = "regulator-fixed";
> > > + regulator-name = "fixed-3.1V";
> > > + regulator-min-microvolt = <3100000>;
> > > + regulator-max-microvolt = <3100000>;
> > > + regulator-always-on;
> > > + };
> > > +};
> > > +
> > > +&pinctrl {
> > > + mmc0_pins: mmc0-pins {
> > > + pinmux {
> > > + groups = "sd0_d0_mfp", "sd0_d1_mfp", "sd0_d2_d3_mfp",
> > > + "sd0_cmd_mfp", "sd0_clk_mfp";
> > > + function = "sd0";
> > > + };
> > > +
> > > + drv-pinconf {
> > > + groups = "sd0_d0_d3_drv", "sd0_cmd_drv", "sd0_clk_drv";
> > > + drive-strength = <8>;
> > > + };
> > > +
> > > + bias0-pinconf {
> > > + pins = "sd0_d0", "sd0_d1", "sd0_d2",
> > > + "sd0_d3", "sd0_cmd";
> > > + bias-pull-up;
> > > + };
> > > +
> > > + bias1-pinconf {
> > > + pins = "sd0_clk";
> > > + bias-pull-down;
> > > + };
> > > + };
> > > +};
> > > +
> > > +/* uSD */
> > > +&mmc0 {
> > > + status = "okay";
> > > + pinctrl-names = "default";
> > > + pinctrl-0 = <&mmc0_pins>;
> > > + no-sdio;
> > > + no-mmc;
> > > + no-1-8-v;
> > > + cd-gpios = <&pinctrl 117 GPIO_ACTIVE_LOW>;
> > > + bus-width = <4>;
> > > + vmmc-supply = <&sd_vcc>;
> > > + vqmmc-supply = <&sd_vcc>;
> > > };
> > >
> > > &twd_timer {
> > > --
> > > 2.29.2
> > >
