On 02/12/2020 16:33, Jernej Škrabec wrote:
Hi,
> Dne sreda, 02. december 2020 ob 14:54:08 CET je Andre Przywara napisal(a):
>> This (relatively) new SoC is similar to the H6, but drops the (broken)
>> PCIe support and the USB 3.0 controller. It also gets the management
>> controller removed, which in turn removes *some*, but not all of the
>> devices formerly dedicated to the ARISC (CPUS).
>> There does not seem to be an external interrupt controller anymore, so
>> no external interrupts through an NMI pin. The AXP driver needs to learn
>> living with that.
>>
>> Signed-off-by: Andre Przywara <andre.przywara@xxxxxxx>
>> ---
>> .../arm64/boot/dts/allwinner/sun50i-h616.dtsi | 704 ++++++++++++++++++
>> 1 file changed, 704 insertions(+)
>> create mode 100644 arch/arm64/boot/dts/allwinner/sun50i-h616.dtsi
>>
>> diff --git a/arch/arm64/boot/dts/allwinner/sun50i-h616.dtsi b/arch/arm64/boot/dts/allwinner/sun50i-h616.dtsi
>> new file mode 100644
>> index 000000000000..dcffbfdcd26b
>> --- /dev/null
>> +++ b/arch/arm64/boot/dts/allwinner/sun50i-h616.dtsi
>> @@ -0,0 +1,704 @@
>> +// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
>> +// Copyright (C) 2020 Arm Ltd.
>> +// based on the H6 dtsi, which is:
>> +// Copyright (C) 2017 Icenowy Zheng <icenowy@xxxxxxx>
>> +
>> +#include <dt-bindings/interrupt-controller/arm-gic.h>
>> +#include <dt-bindings/clock/sun50i-h616-ccu.h>
>> +#include <dt-bindings/clock/sun50i-h6-r-ccu.h>
>> +#include <dt-bindings/reset/sun50i-h616-ccu.h>
>> +#include <dt-bindings/reset/sun50i-h6-r-ccu.h>
>> +
>> +/ {
>> + interrupt-parent = <&gic>;
>> + #address-cells = <2>;
>> + #size-cells = <2>;
>> +
>> + cpus {
>> + #address-cells = <1>;
>> + #size-cells = <0>;
>> +
>> + cpu0: cpu@0 {
>> + compatible = "arm,cortex-a53";
>> + device_type = "cpu";
>> + reg = <0>;
>> + enable-method = "psci";
>> + clocks = <&ccu CLK_CPUX>;
>> + };
>> +
>> + cpu1: cpu@1 {
>> + compatible = "arm,cortex-a53";
>> + device_type = "cpu";
>> + reg = <1>;
>> + enable-method = "psci";
>> + clocks = <&ccu CLK_CPUX>;
>> + };
>> +
>> + cpu2: cpu@2 {
>> + compatible = "arm,cortex-a53";
>> + device_type = "cpu";
>> + reg = <2>;
>> + enable-method = "psci";
>> + clocks = <&ccu CLK_CPUX>;
>> + };
>> +
>> + cpu3: cpu@3 {
>> + compatible = "arm,cortex-a53";
>> + device_type = "cpu";
>> + reg = <3>;
>> + enable-method = "psci";
>> + clocks = <&ccu CLK_CPUX>;
>> + };
>> + };
>> +
>> + reserved-memory {
>> + #address-cells = <2>;
>> + #size-cells = <2>;
>> + ranges;
>> +
>> + /* 512KiB reserved for ARM Trusted Firmware (BL31) */
>> + secmon_reserved: secmon@40000000 {
>> + reg = <0x0 0x40000000 0x0 0x80000>;
>> + no-map;
>> + };
>> + };
>> +
>> + osc24M: osc24M_clk {
>> + #clock-cells = <0>;
>> + compatible = "fixed-clock";
>> + clock-frequency = <24000000>;
>> + clock-output-names = "osc24M";
>> + };
>> +
>> + pmu {
>> + compatible = "arm,cortex-a53-pmu";
>> + interrupts = <GIC_SPI 140 IRQ_TYPE_LEVEL_HIGH>,
>> + <GIC_SPI 141 IRQ_TYPE_LEVEL_HIGH>,
>> + <GIC_SPI 142 IRQ_TYPE_LEVEL_HIGH>,
>> + <GIC_SPI 143 IRQ_TYPE_LEVEL_HIGH>;
>> + interrupt-affinity = <&cpu0>, <&cpu1>, <&cpu2>, <&cpu3>;
>> + };
>> +
>> + psci {
>> + compatible = "arm,psci-0.2";
>> + method = "smc";
>> + };
>> +
>> + timer {
>> + compatible = "arm,armv8-timer";
>> + arm,no-tick-in-suspend;
>> + interrupts = <GIC_PPI 13
>> + (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_HIGH)>,
>> + <GIC_PPI 14
>> + (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_HIGH)>,
>> + <GIC_PPI 11
>> + (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_HIGH)>,
>> + <GIC_PPI 10
>> + (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_HIGH)>;
>> + };
>> +
>> + soc {
>> + compatible = "simple-bus";
>> + #address-cells = <1>;
>> + #size-cells = <1>;
>> + ranges = <0x0 0x0 0x0 0x40000000>;
>> +
>> + syscon: syscon@3000000 {
>> + compatible = "allwinner,sun50i-h616-system-control",
>> + "allwinner,sun50i-a64-system-control";
>
> Those H616 is not compatible to A64 one because it has second emac control
> register at offset 0x34, which no other supported SoC has.
But this means the H616 is a superset of the A64?
I changed the driver to extend the regmap to two registers for the H616,
is that all you need for the second emac?
How do we tell the EMAC driver which clock register to use? An extra
compatible? Or can we pass a cell to syscon? syscon = <&syscon 1>; ? Or
an extra property?
>
>> + reg = <0x03000000 0x1000>;
>> + #address-cells = <1>;
>> + #size-cells = <1>;
>> + ranges;
>> +
>> + sram_c: sram@28000 {
>> + compatible = "mmio-sram";
>> + reg = <0x00028000 0x30000>;
>> + #address-cells = <1>;
>> + #size-cells = <1>;
>> + ranges = <0 0x00028000 0x30000>;
>> + };
>> +
>> + sram_c1: sram@1a00000 {
>> + compatible = "mmio-sram";
>> + reg = <0x01a00000 0x200000>;
>> + #address-cells = <1>;
>> + #size-cells = <1>;
>> + ranges = <0 0x01a00000 0x200000>;
>> +
>> + ve_sram: sram-section@0 {
>> + compatible = "allwinner,sun50i-h616-sram-c1",
>> + "allwinner,sun4i-a10-sram-c1";
>> + reg = <0x000000 0x200000>;
>> + };
>> + };
>> + };
>> +
>> + ccu: clock@3001000 {
>> + compatible = "allwinner,sun50i-h616-ccu";
>> + reg = <0x03001000 0x1000>;
>> + clocks = <&osc24M>, <&rtc 0>, <&rtc 2>;
>> + clock-names = "hosc", "losc", "iosc";
>> + #clock-cells = <1>;
>> + #reset-cells = <1>;
>> + };
>> +
>> + watchdog: watchdog@30090a0 {
>> + compatible = "allwinner,sun50i-h616-wdt",
>> + "allwinner,sun6i-a31-wdt";
>> + reg = <0x030090a0 0x20>;
>> + interrupts = <GIC_SPI 50 IRQ_TYPE_LEVEL_HIGH>;
>> + clocks = <&osc24M>;
>> + status = "disabled";
>> + };
>> +
>> + pio: pinctrl@300b000 {
>> + compatible = "allwinner,sun50i-h616-pinctrl";
>> + reg = <0x0300b000 0x400>;
>> + interrupts = <GIC_SPI 52 IRQ_TYPE_LEVEL_HIGH>,
>> + <GIC_SPI 54 IRQ_TYPE_LEVEL_HIGH>,
>> + <GIC_SPI 55 IRQ_TYPE_LEVEL_HIGH>,
>> + <GIC_SPI 56 IRQ_TYPE_LEVEL_HIGH>,
>> + <GIC_SPI 57 IRQ_TYPE_LEVEL_HIGH>;
>> + clocks = <&ccu CLK_APB1>, <&osc24M>, <&rtc 0>;
>> + clock-names = "apb", "hosc", "losc";
>> + gpio-controller;
>> + #gpio-cells = <3>;
>> + interrupt-controller;
>> + #interrupt-cells = <3>;
>> +
>> + ext_rgmii_pins: rgmii-pins {
>> + pins = "PI0", "PI1", "PI2", "PI3", "PI4",
>> + "PI5", "PI7", "PI8", "PI9", "PI10",
>> + "PI11", "PI12", "PI13", "PI14", "PI15",
>> + "PI16";
>> + function = "emac0";
>> + drive-strength = <40>;
>> + };
>> +
>> + i2c0_pins: i2c0-pins {
>> + pins = "PI6", "PI7";
>> + function = "i2c0";
>> + };
>> +
>> + i2c3_pins_a: i2c1-pins-a {
>> + pins = "PH4", "PH5";
>> + function = "i2c3";
>> + };
>> +
>> + ir_rx_pin: ir_rx_pin {
>> + pins = "PH10";
>> + function = "ir_rx";
>> + };
>> +
>> + mmc0_pins: mmc0-pins {
>> + pins = "PF0", "PF1", "PF2", "PF3",
>> + "PF4", "PF5";
>> + function = "mmc0";
>> + drive-strength = <30>;
>> + bias-pull-up;
>> + };
>> +
>> + mmc1_pins: mmc1-pins {
>> + pins = "PG0", "PG1", "PG2", "PG3",
>> + "PG4", "PG5";
>> + function = "mmc1";
>> + drive-strength = <30>;
>> + bias-pull-up;
>> + };
>> +
>> + mmc2_pins: mmc2-pins {
>> + pins = "PC0", "PC1", "PC5", "PC6",
>> + "PC8", "PC9", "PC10", "PC11",
>> + "PC13", "PC14", "PC15", "PC16";
>> + function = "mmc2";
>> + drive-strength = <30>;
>> + bias-pull-up;
>> + };
>> +
>> + spi0_pins: spi0-pins {
>> + pins = "PC0", "PC2", "PC3", "PC4";
>> + function = "spi0";
>> + };
>> +
>> + spi1_pins: spi1-pins {
>> + pins = "PH6", "PH7", "PH8";
>> + function = "spi1";
>> + };
>> +
>> + spi1_cs_pin: spi1-cs-pin {
>> + pins = "PH5";
>> + function = "spi1";
>> + };
>> +
>> + uart0_ph_pins: uart0-ph-pins {
>> + pins = "PH0", "PH1";
>> + function = "uart0";
>> + };
>> +
>> + uart1_pins: uart1-pins {
>> + pins = "PG6", "PG7";
>> + function = "uart1";
>> + };
>> +
>> + uart1_rts_cts_pins: uart1-rts-cts-pins {
>> + pins = "PG8", "PG9";
>> + function = "uart1";
>> + };
>> + };
>> +
>> + gic: interrupt-controller@3021000 {
>> + compatible = "arm,gic-400";
>> + reg = <0x03021000 0x1000>,
>> + <0x03022000 0x2000>,
>> + <0x03024000 0x2000>,
>> + <0x03026000 0x2000>;
>> + interrupts = <GIC_PPI 9 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_HIGH)>;
>> + interrupt-controller;
>> + #interrupt-cells = <3>;
>> + };
>> +
>> + mmc0: mmc@4020000 {
>> + compatible = "allwinner,sun50i-h616-mmc",
>> + "allwinner,sun50i-a100-mmc";
>> + reg = <0x04020000 0x1000>;
>> + clocks = <&ccu CLK_BUS_MMC0>, <&ccu CLK_MMC0>;
>> + clock-names = "ahb", "mmc";
>> + resets = <&ccu RST_BUS_MMC0>;
>> + reset-names = "ahb";
>> + interrupts = <GIC_SPI 35 IRQ_TYPE_LEVEL_HIGH>;
>> + pinctrl-names = "default";
>> + pinctrl-0 = <&mmc0_pins>;
>> + status = "disabled";
>> + #address-cells = <1>;
>> + #size-cells = <0>;
>> + };
>> +
>> + mmc1: mmc@4021000 {
>> + compatible = "allwinner,sun50i-h616-mmc",
>> + "allwinner,sun50i-a100-mmc";
>> + reg = <0x04021000 0x1000>;
>> + clocks = <&ccu CLK_BUS_MMC1>, <&ccu CLK_MMC1>;
>> + clock-names = "ahb", "mmc";
>> + resets = <&ccu RST_BUS_MMC1>;
>> + reset-names = "ahb";
>> + interrupts = <GIC_SPI 36 IRQ_TYPE_LEVEL_HIGH>;
>> + pinctrl-names = "default";
>> + pinctrl-0 = <&mmc1_pins>;
>> + status = "disabled";
>> + #address-cells = <1>;
>> + #size-cells = <0>;
>> + };
>> +
>> + mmc2: mmc@4022000 {
>> + compatible = "allwinner,sun50i-h616-emmc",
>> + "allwinner,sun50i-a64-emmc";
>> + reg = <0x04022000 0x1000>;
>> + clocks = <&ccu CLK_BUS_MMC2>, <&ccu CLK_MMC2>;
>> + clock-names = "ahb", "mmc";
>> + resets = <&ccu RST_BUS_MMC2>;
>> + reset-names = "ahb";
>> + interrupts = <GIC_SPI 37 IRQ_TYPE_LEVEL_HIGH>;
>> + pinctrl-names = "default";
>> + pinctrl-0 = <&mmc2_pins>;
>> + status = "disabled";
>> + #address-cells = <1>;
>> + #size-cells = <0>;
>> + };
>
> I would skip mmc1 and mmc2, as they were not proved to be working yet.
You mentioned on IRC that MMC2 is working now. Can we check the
existence of the WiFi chip on mmc1 somehow? Without having a proper
driver, just to prove that this works?
Does your TV box also use this new Allwinner WiFi chip?
>> +
>> + uart0: serial@5000000 {
>> + compatible = "snps,dw-apb-uart";
>> + reg = <0x05000000 0x400>;
>> + interrupts = <GIC_SPI 0 IRQ_TYPE_LEVEL_HIGH>;
>> + reg-shift = <2>;
>> + reg-io-width = <4>;
>> + clocks = <&ccu CLK_BUS_UART0>;
>> + resets = <&ccu RST_BUS_UART0>;
>> + status = "disabled";
>> + };
>> +
>> + uart1: serial@5000400 {
>> + compatible = "snps,dw-apb-uart";
>> + reg = <0x05000400 0x400>;
>> + interrupts = <GIC_SPI 1 IRQ_TYPE_LEVEL_HIGH>;
>> + reg-shift = <2>;
>> + reg-io-width = <4>;
>> + clocks = <&ccu CLK_BUS_UART1>;
>> + resets = <&ccu RST_BUS_UART1>;
>> + status = "disabled";
>> + };
>> +
>> + uart2: serial@5000800 {
>> + compatible = "snps,dw-apb-uart";
>> + reg = <0x05000800 0x400>;
>> + interrupts = <GIC_SPI 2 IRQ_TYPE_LEVEL_HIGH>;
>> + reg-shift = <2>;
>> + reg-io-width = <4>;
>> + clocks = <&ccu CLK_BUS_UART2>;
>> + resets = <&ccu RST_BUS_UART2>;
>> + status = "disabled";
>> + };
>> +
>> + uart3: serial@5000c00 {
>> + compatible = "snps,dw-apb-uart";
>> + reg = <0x05000c00 0x400>;
>> + interrupts = <GIC_SPI 3 IRQ_TYPE_LEVEL_HIGH>;
>> + reg-shift = <2>;
>> + reg-io-width = <4>;
>> + clocks = <&ccu CLK_BUS_UART3>;
>> + resets = <&ccu RST_BUS_UART3>;
>> + status = "disabled";
>> + };
>> +
>> + uart4: serial@5001000 {
>> + compatible = "snps,dw-apb-uart";
>> + reg = <0x05001000 0x400>;
>> + interrupts = <GIC_SPI 4 IRQ_TYPE_LEVEL_HIGH>;
>> + reg-shift = <2>;
>> + reg-io-width = <4>;
>> + clocks = <&ccu CLK_BUS_UART4>;
>> + resets = <&ccu RST_BUS_UART4>;
>> + status = "disabled";
>> + };
>> +
>> + uart5: serial@5001400 {
>> + compatible = "snps,dw-apb-uart";
>> + reg = <0x05001400 0x400>;
>> + interrupts = <GIC_SPI 5 IRQ_TYPE_LEVEL_HIGH>;
>> + reg-shift = <2>;
>> + reg-io-width = <4>;
>> + clocks = <&ccu CLK_BUS_UART5>;
>> + resets = <&ccu RST_BUS_UART5>;
>> + status = "disabled";
>> + };
>> +
>> + i2c0: i2c@5002000 {
>> + compatible = "allwinner,sun50i-h616-i2c",
>> + "allwinner,sun6i-a31-i2c";
>> + reg = <0x05002000 0x400>;
>> + interrupts = <GIC_SPI 6 IRQ_TYPE_LEVEL_HIGH>;
>> + clocks = <&ccu CLK_BUS_I2C0>;
>> + resets = <&ccu RST_BUS_I2C0>;
>> + pinctrl-names = "default";
>> + pinctrl-0 = <&i2c0_pins>;
>> + status = "disabled";
>> + #address-cells = <1>;
>> + #size-cells = <0>;
>> + };
>> +
>> + i2c1: i2c@5002400 {
>> + compatible = "allwinner,sun50i-h616-i2c",
>> + "allwinner,sun6i-a31-i2c";
>> + reg = <0x05002400 0x400>;
>> + interrupts = <GIC_SPI 7 IRQ_TYPE_LEVEL_HIGH>;
>> + clocks = <&ccu CLK_BUS_I2C1>;
>> + resets = <&ccu RST_BUS_I2C1>;
>> + status = "disabled";
>> + #address-cells = <1>;
>> + #size-cells = <0>;
>> + };
>> +
>> + i2c2: i2c@5002800 {
>> + compatible = "allwinner,sun50i-h616-i2c",
>> + "allwinner,sun6i-a31-i2c";
>> + reg = <0x05002800 0x400>;
>> + interrupts = <GIC_SPI 8 IRQ_TYPE_LEVEL_HIGH>;
>> + clocks = <&ccu CLK_BUS_I2C2>;
>> + resets = <&ccu RST_BUS_I2C2>;
>> + status = "disabled";
>> + #address-cells = <1>;
>> + #size-cells = <0>;
>> + };
>> +
>> + i2c3: i2c@5002c00 {
>> + compatible = "allwinner,sun50i-h616-i2c",
>> + "allwinner,sun6i-a31-i2c";
>> + reg = <0x05002c00 0x400>;
>> + interrupts = <GIC_SPI 9 IRQ_TYPE_LEVEL_HIGH>;
>> + clocks = <&ccu CLK_BUS_I2C3>;
>> + resets = <&ccu RST_BUS_I2C3>;
>> + status = "disabled";
>> + #address-cells = <1>;
>> + #size-cells = <0>;
>> + };
>> +
>> + i2c4: i2c@5003000 {
>> + compatible = "allwinner,sun50i-h616-i2c",
>> + "allwinner,sun6i-a31-i2c";
>> + reg = <0x05003000 0x400>;
>> + interrupts = <GIC_SPI 10 IRQ_TYPE_LEVEL_HIGH>;
>> + clocks = <&ccu CLK_BUS_I2C4>;
>> + resets = <&ccu RST_BUS_I2C4>;
>> + status = "disabled";
>> + #address-cells = <1>;
>> + #size-cells = <0>;
>> + };
>> +
>> + spi0: spi@5010000 {
>> + compatible = "allwinner,sun50i-h616-spi",
>> + "allwinner,sun8i-h3-spi";
>> + reg = <0x05010000 0x1000>;
>> + interrupts = <GIC_SPI 12 IRQ_TYPE_LEVEL_HIGH>;
>> + clocks = <&ccu CLK_BUS_SPI0>, <&ccu CLK_SPI0>;
>> + clock-names = "ahb", "mod";
>> + resets = <&ccu RST_BUS_SPI0>;
>> + pinctrl-names = "default";
>> + pinctrl-0 = <&spi0_pins>;
>> + status = "disabled";
>> + #address-cells = <1>;
>> + #size-cells = <0>;
>> + };
>> +
>> + spi1: spi@5011000 {
>> + compatible = "allwinner,sun50i-h616-spi",
>> + "allwinner,sun8i-h3-spi";
>> + reg = <0x05011000 0x1000>;
>> + interrupts = <GIC_SPI 13 IRQ_TYPE_LEVEL_HIGH>;
>> + clocks = <&ccu CLK_BUS_SPI1>, <&ccu CLK_SPI1>;
>> + clock-names = "ahb", "mod";
>> + resets = <&ccu RST_BUS_SPI1>;
>> + pinctrl-names = "default";
>> + pinctrl-0 = <&spi1_pins>;
>> + status = "disabled";
>> + #address-cells = <1>;
>> + #size-cells = <0>;
>> + };
>> +
>> + emac0: ethernet@5020000 {
>> + compatible = "allwinner,sun50i-h616-emac",
>> + "allwinner,sun50i-a64-emac";
>> + syscon = <&syscon>;
>> + reg = <0x05020000 0x10000>;
>> + interrupts = <GIC_SPI 14 IRQ_TYPE_LEVEL_HIGH>;
>> + interrupt-names = "macirq";
>> + resets = <&ccu RST_BUS_EMAC0>;
>> + reset-names = "stmmaceth";
>> + clocks = <&ccu CLK_BUS_EMAC0>;
>> + clock-names = "stmmaceth";
>> + status = "disabled";
>> +
>> + mdio: mdio {
>> + compatible = "snps,dwmac-mdio";
>> + #address-cells = <1>;
>> + #size-cells = <0>;
>> + };
>> + };
>> +
>> + usbotg: usb@5100000 {
>> + compatible = "allwinner,sun50i-h616-musb",
>> + "allwinner,sun8i-a33-musb";
>> + reg = <0x05100000 0x0400>;
>> + clocks = <&ccu CLK_BUS_OTG>;
>> + resets = <&ccu RST_BUS_OTG>;
>> + interrupts = <GIC_SPI 25 IRQ_TYPE_LEVEL_HIGH>;
>> + interrupt-names = "mc";
>> + phys = <&usbphy 0>;
>> + phy-names = "usb";
>> + extcon = <&usbphy 0>;
>> + status = "disabled";
>> + };
>> +
>> + usbphy: phy@5100400 {
>> + compatible = "allwinner,sun50i-h616-usb-phy";
>> + reg = <0x05100400 0x24>,
>> + <0x05101800 0x4>,
>> + <0x05200800 0x4>,
>> + <0x05310800 0x4>,
>> + <0x05311800 0x4>;
>> + reg-names = "phy_ctrl",
>> + "pmu0",
>> + "pmu1",
>> + "pmu2",
>> + "pmu3";
>> + clocks = <&ccu CLK_USB_PHY0>,
>> + <&ccu CLK_USB_PHY1>,
>> + <&ccu CLK_USB_PHY2>,
>> + <&ccu CLK_USB_PHY3>;
>> + clock-names = "usb0_phy",
>> + "usb1_phy",
>> + "usb2_phy",
>> + "usb3_phy";
>> + resets = <&ccu RST_USB_PHY0>,
>> + <&ccu RST_USB_PHY1>,
>> + <&ccu RST_USB_PHY2>,
>> + <&ccu RST_USB_PHY3>;
>> + reset-names = "usb0_reset",
>> + "usb1_reset",
>> + "usb2_reset",
>> + "usb3_reset";
>> + status = "disabled";
>> + #phy-cells = <1>;
>> + };
>> +
>> + ehci0: usb@5101000 {
>> + compatible = "allwinner,sun50i-h616-ehci",
>> + "generic-ehci";
>> + reg = <0x05101000 0x100>;
>> + interrupts = <GIC_SPI 26 IRQ_TYPE_LEVEL_HIGH>;
>> + clocks = <&ccu CLK_BUS_OHCI0>,
>> + <&ccu CLK_BUS_EHCI0>,
>> + <&ccu CLK_USB_OHCI0>;
>> + resets = <&ccu RST_BUS_OHCI0>,
>> + <&ccu RST_BUS_EHCI0>;
>> + status = "disabled";
>> + };
>> +
>> + ohci0: usb@5101400 {
>> + compatible = "allwinner,sun50i-h616-ohci",
>> + "generic-ohci";
>> + reg = <0x05101400 0x100>;
>> + interrupts = <GIC_SPI 27 IRQ_TYPE_LEVEL_HIGH>;
>> + clocks = <&ccu CLK_BUS_OHCI0>,
>> + <&ccu CLK_USB_OHCI0>;
>> + resets = <&ccu RST_BUS_OHCI0>;
>> + status = "disabled";
>> + };
>> +
>> + ehci1: usb@5200000 {
>> + compatible = "allwinner,sun50i-h616-ehci",
>> + "generic-ehci";
>> + reg = <0x05200000 0x100>;
>> + interrupts = <GIC_SPI 28 IRQ_TYPE_LEVEL_HIGH>;
>> + clocks = <&ccu CLK_BUS_OHCI1>,
>> + <&ccu CLK_BUS_EHCI1>,
>> + <&ccu CLK_USB_OHCI1>;
>> + resets = <&ccu RST_BUS_OHCI1>,
>> + <&ccu RST_BUS_EHCI1>;
>> + phys = <&usbphy 1>;
>> + phy-names = "usb";
>> + status = "disabled";
>> + };
>> +
>> + ohci1: usb@5200400 {
>> + compatible = "allwinner,sun50i-h616-ohci",
>> + "generic-ohci";
>> + reg = <0x05200400 0x100>;
>> + interrupts = <GIC_SPI 29 IRQ_TYPE_LEVEL_HIGH>;
>> + clocks = <&ccu CLK_BUS_OHCI1>,
>> + <&ccu CLK_USB_OHCI1>;
>> + resets = <&ccu RST_BUS_OHCI1>;
>> + phys = <&usbphy 1>;
>> + phy-names = "usb";
>> + status = "disabled";
>> + };
>> +
>> + ehci2: usb@5310000 {
>> + compatible = "allwinner,sun50i-h616-ehci",
>> + "generic-ehci";
>> + reg = <0x05310000 0x100>;
>> + interrupts = <GIC_SPI 30 IRQ_TYPE_LEVEL_HIGH>;
>> + clocks = <&ccu CLK_BUS_OHCI2>,
>> + <&ccu CLK_BUS_EHCI2>,
>> + <&ccu CLK_USB_OHCI2>;
>> + resets = <&ccu RST_BUS_OHCI2>,
>> + <&ccu RST_BUS_EHCI2>;
>> + phys = <&usbphy 2>;
>> + phy-names = "usb";
>> + status = "disabled";
>> + };
>> +
>> + ohci2: usb@5310400 {
>> + compatible = "allwinner,sun50i-h616-ohci",
>> + "generic-ohci";
>> + reg = <0x05310400 0x100>;
>> + interrupts = <GIC_SPI 31 IRQ_TYPE_LEVEL_HIGH>;
>> + clocks = <&ccu CLK_BUS_OHCI2>,
>> + <&ccu CLK_USB_OHCI2>;
>> + resets = <&ccu RST_BUS_OHCI2>;
>> + phys = <&usbphy 2>;
>> + phy-names = "usb";
>> + status = "disabled";
>> + };
>> +
>> + ehci3: usb@5311000 {
>> + compatible = "allwinner,sun50i-h616-ehci",
>> + "generic-ehci";
>> + reg = <0x05311000 0x100>;
>> + interrupts = <GIC_SPI 32 IRQ_TYPE_LEVEL_HIGH>;
>> + clocks = <&ccu CLK_BUS_OHCI3>,
>> + <&ccu CLK_BUS_EHCI3>,
>> + <&ccu CLK_USB_OHCI3>;
>> + resets = <&ccu RST_BUS_OHCI3>,
>> + <&ccu RST_BUS_EHCI3>;
>> + phys = <&usbphy 3>;
>> + phy-names = "usb";
>> + status = "disabled";
>> + };
>> +
>> + ohci3: usb@5311400 {
>> + compatible = "allwinner,sun50i-h616-ohci",
>> + "generic-ohci";
>> + reg = <0x05311400 0x100>;
>> + interrupts = <GIC_SPI 33 IRQ_TYPE_LEVEL_HIGH>;
>> + clocks = <&ccu CLK_BUS_OHCI3>,
>> + <&ccu CLK_USB_OHCI3>;
>> + resets = <&ccu RST_BUS_OHCI3>;
>> + phys = <&usbphy 3>;
>> + phy-names = "usb";
>> + status = "disabled";
>> + };
>> +
>> + rtc: rtc@7000000 {
>> + compatible = "allwinner,sun50i-h616-rtc",
>> + "allwinner,sun50i-h6-rtc";
>> + reg = <0x07000000 0x400>;
>> + interrupts = <GIC_SPI 101 IRQ_TYPE_LEVEL_HIGH>,
>> + <GIC_SPI 102 IRQ_TYPE_LEVEL_HIGH>;
>> + clock-output-names = "osc32k", "osc32k-out", "iosc";
>> + #clock-cells = <1>;
>> + };
>> +
>> + r_ccu: clock@7010000 {
>> + compatible = "allwinner,sun50i-h616-r-ccu";
>> + reg = <0x07010000 0x400>;
>> + clocks = <&osc24M>, <&rtc 0>, <&rtc 2>,
>> + <&ccu CLK_PLL_PERIPH0>;
>> + clock-names = "hosc", "losc", "iosc", "pll-periph";
>> + #clock-cells = <1>;
>> + #reset-cells = <1>;
>> + };
>> +
>> + r_pio: pinctrl@7022000 {
>> + compatible = "allwinner,sun50i-h616-r-pinctrl";
>> + reg = <0x07022000 0x400>;
>> + interrupts = <GIC_SPI 43 IRQ_TYPE_LEVEL_HIGH>;
>> + clocks = <&r_ccu CLK_R_APB1>, <&osc24M>, <&rtc 0>;
>> + clock-names = "apb", "hosc", "losc";
>> + gpio-controller;
>> + #gpio-cells = <3>;
>> + interrupt-controller;
>> + #interrupt-cells = <3>;
>> +
>> + r_i2c_pins: r-i2c-pins {
>> + pins = "PL0", "PL1";
>> + function = "s_i2c";
>> + };
>> + };
>> +
>> + ir: ir@7040000 {
>> + compatible = "allwinner,sun50i-h616-ir",
>> + "allwinner,sun6i-a31-ir";
>> + reg = <0x07040000 0x400>;
>> + interrupts = <GIC_SPI 106 IRQ_TYPE_LEVEL_HIGH>;
>> + clocks = <&ccu CLK_R_APB1_IR>,
>> + <&ccu CLK_IR>;
>
> Above clocks and reset below should reference r_ccu.
Ah, indeed, thanks for spotting this!
> Maybe we should call
> clock CLK_R_IR to know it comes from second clock controller?
Yeah, but it's a bit tricky, since this is shared with the H6, and I'd
rather avoid the churn of changing the H6 .dtsi as well.
Cheers,
Andre
>
> Best regards,
> Jernej
>
>> + clock-names = "apb", "ir";
>> + resets = <&ccu RST_R_APB1_IR>;
>> + pinctrl-names = "default";
>> + pinctrl-0 = <&ir_rx_pin>;
>> + status = "disabled";
>> + };
>> +
>> + r_i2c: i2c@7081400 {
>> + compatible = "allwinner,sun50i-h616-i2c",
>> + "allwinner,sun6i-a31-i2c";
>> + reg = <0x07081400 0x400>;
>> + interrupts = <GIC_SPI 105 IRQ_TYPE_LEVEL_HIGH>;
>> + clocks = <&r_ccu CLK_R_APB2_I2C>;
>> + resets = <&r_ccu RST_R_APB2_I2C>;
>> + status = "disabled";
>> + #address-cells = <1>;
>> + #size-cells = <0>;
>> + };
>> + };
>> +};
>> --
>> 2.17.5
>>
>>
>
>
