[PATCH] ARM: dts: mvebu: Add device tree for ATL-x530 Board

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



Add device tree file for x530 board. This has an Armada 385 SoC. Has
NAND-flash for user storage and SPI for booting. Covers majority of x530
and GS980MX variants.

Signed-off-by: Aryan Srivastava <aryan.srivastava@xxxxxxxxxxxxxxxxxxx>
Reviewed-by: Chris Packham <chris.packham@xxxxxxxxxxxxxxxxxxx>
---
 arch/arm/boot/dts/armada-385-atl-x530.dts | 235 ++++++++++++++++++++++
 1 file changed, 235 insertions(+)
 create mode 100644 arch/arm/boot/dts/armada-385-atl-x530.dts

diff --git a/arch/arm/boot/dts/armada-385-atl-x530.dts b/arch/arm/boot/dts/armada-385-atl-x530.dts
new file mode 100644
index 000000000000..2041bf09c578
--- /dev/null
+++ b/arch/arm/boot/dts/armada-385-atl-x530.dts
@@ -0,0 +1,235 @@
+// SPDX-License-Identifier: (GPL-2.0 OR MIT)
+/*
+ * Device Tree file for Armada 385 Allied Telesis x530/GS980MX Board.
+ (x530/AT-GS980MX)
+ *
+ Copyright (C) 2020 Allied Telesis Labs
+ */
+
+/dts-v1/;
+#include "armada-385.dtsi"
+
+#include <dt-bindings/gpio/gpio.h>
+
+/ {
+	model = "x530/AT-GS980MX";
+	compatible = "alliedtelesis,gs980mx", "alliedtelesis,x530", "marvell,armada385", "marvell,armada380";
+
+	chosen {
+		stdout-path = "serial1:115200n8";
+	};
+
+	memory {
+		device_type = "memory";
+		reg = <0x00000000 0x40000000>; /* 1GB */
+	};
+
+	soc {
+		ranges = <MBUS_ID(0xf0, 0x01) 0 0xf1000000 0x100000
+			  MBUS_ID(0x01, 0x3d) 0 0xf4800000 0x80000
+			  MBUS_ID(0x01, 0x1d) 0 0xfff00000 0x100000>;
+
+		internal-regs {
+			i2c0: i2c@11000 {
+				pinctrl-names = "default";
+				pinctrl-0 = <&i2c0_pins>;
+				status = "okay";
+			};
+
+			uart0: serial@12000 {
+				pinctrl-names = "default";
+				pinctrl-0 = <&uart0_pins>;
+				status = "okay";
+			};
+		};
+	};
+};
+
+&pciec {
+	status = "okay";
+};
+
+&pcie1 {
+	status = "okay";
+	reset-gpios = <&gpio1 23 GPIO_ACTIVE_LOW>;
+	reset-delay-us = <400000>;
+};
+
+&pcie2 {
+	status = "okay";
+};
+
+&devbus_cs1 {
+	compatible = "marvell,mvebu-devbus";
+	status = "okay";
+
+	devbus,bus-width    = <8>;
+	devbus,turn-off-ps  = <60000>;
+	devbus,badr-skew-ps = <0>;
+	devbus,acc-first-ps = <124000>;
+	devbus,acc-next-ps  = <248000>;
+	devbus,rd-setup-ps  = <0>;
+	devbus,rd-hold-ps   = <0>;
+
+	/* Write parameters */
+	devbus,sync-enable = <0>;
+	devbus,wr-high-ps  = <60000>;
+	devbus,wr-low-ps   = <60000>;
+	devbus,ale-wr-ps   = <60000>;
+
+	nvs@0 {
+		status = "okay";
+
+		compatible = "mtd-ram";
+		reg = <0 0x00080000>;
+		bank-width = <1>;
+		label = "nvs";
+	};
+};
+
+&pinctrl {
+	i2c0_gpio_pins: i2c-gpio-pins-0 {
+		marvell,pins = "mpp2", "mpp3";
+		marvell,function = "gpio";
+	};
+};
+
+&i2c0 {
+	clock-frequency = <100000>;
+	status = "okay";
+
+	pinctrl-names = "default", "gpio";
+	pinctrl-0 = <&i2c0_pins>;
+	pinctrl-1 = <&i2c0_gpio_pins>;
+	scl-gpio = <&gpio0 2 (GPIO_ACTIVE_HIGH|GPIO_OPEN_DRAIN)>;
+	sda-gpio = <&gpio0 3 (GPIO_ACTIVE_HIGH|GPIO_OPEN_DRAIN)>;
+
+	i2c0mux: mux@71 {
+		#address-cells = <1>;
+		#size-cells = <0>;
+		compatible = "nxp,pca9544";
+		reg = <0x71>;
+		i2c-mux-idle-disconnect;
+
+		i2c@0 { /* POE devices MUX */
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0>;
+		};
+
+		i2c@1 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <1>;
+
+			adt7476_2e: hwmon@2e {
+				compatible = "adi,adt7476";
+				reg = <0x2e>;
+			};
+
+			adt7476_2d: hwmon@2d {
+				compatible = "adi,adt7476";
+				reg = <0x2d>;
+			};
+		};
+
+		i2c@2 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <2>;
+
+			rtc@68 {
+				compatible = "dallas,ds1340";
+				reg = <0x68>;
+			};
+		};
+
+		i2c@3 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <3>;
+
+			gpio@20 {
+				compatible = "nxp,pca9554";
+				gpio-controller;
+				#gpio-cells = <2>;
+				reg = <0x20>;
+			};
+		};
+	};
+};
+
+&usb0 {
+	status = "okay";
+};
+
+&spi1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&spi1_pins>;
+	status = "okay";
+
+	spi-flash@0 {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		compatible = "jedec,spi-nor";
+		reg = <1>; /* Chip select 1 */
+		spi-max-frequency = <54000000>;
+
+		partitions {
+			compatible = "fixed-partitions";
+			#address-cells = <1>;
+			#size-cells = <1>;
+			partition@u-boot {
+				reg = <0x00000000 0x00100000>;
+				label = "u-boot";
+			};
+			partition@u-boot-env {
+				reg = <0x00100000 0x00040000>;
+				label = "u-boot-env";
+			};
+			partition@unused {
+				reg = <0x00140000 0x00e80000>;
+				label = "unused";
+			};
+			partition@idprom {
+				reg = <0x00fc0000 0x00040000>;
+				label = "idprom";
+			};
+		};
+	};
+};
+
+&nand_controller {
+	status = "okay";
+
+	nand@0 {
+		reg = <0>;
+		label = "pxa3xx_nand-0";
+		nand-rb = <0>;
+		nand-on-flash-bbt;
+		nand-ecc-strength = <4>;
+		nand-ecc-step-size = <512>;
+
+		marvell,nand-enable-arbiter;
+
+		partitions {
+			compatible = "fixed-partitions";
+			#address-cells = <1>;
+			#size-cells = <1>;
+			partition@user {
+				reg = <0x00000000 0x0f000000>;
+				label = "user";
+			};
+			partition@errlog {
+				/* Maximum mtdoops size is 8MB, so set to that. */
+				reg = <0x0f000000 0x00800000>;
+				label = "errlog";
+			};
+			partition@nand-bbt {
+				reg = <0x0f800000 0x00800000>;
+				label = "nand-bbt";
+			};
+		};
+	};
+};
+
-- 
2.29.2




[Index of Archives]     [Device Tree Compilter]     [Device Tree Spec]     [Linux Driver Backports]     [Video for Linux]     [Linux USB Devel]     [Linux PCI Devel]     [Linux Audio Users]     [Linux Kernel]     [Linux SCSI]     [XFree86]     [Yosemite Backpacking]


  Powered by Linux