[PATCH v7 5/6] dt-bindings: spi: Convert cadence-quadspi.txt to cadence-quadspi.yaml

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



From: Ramuthevar Vadivel Murugan <vadivel.muruganx.ramuthevar@xxxxxxxxxxxxxxx>

Convert the cadence-quadspi.txt documentation to cadence-quadspi.yaml
remove the cadence-quadspi.txt from Documentation/devicetree/bindings/spi/

Signed-off-by: Ramuthevar Vadivel Murugan <vadivel.muruganx.ramuthevar@xxxxxxxxxxxxxxx>
---
 .../devicetree/bindings/spi/cadence-quadspi.txt    |  67 ----------
 .../devicetree/bindings/spi/cdns,qspi-nor.yaml     | 147 +++++++++++++++++++++
 2 files changed, 147 insertions(+), 67 deletions(-)
 delete mode 100644 Documentation/devicetree/bindings/spi/cadence-quadspi.txt
 create mode 100644 Documentation/devicetree/bindings/spi/cdns,qspi-nor.yaml

diff --git a/Documentation/devicetree/bindings/spi/cadence-quadspi.txt b/Documentation/devicetree/bindings/spi/cadence-quadspi.txt
deleted file mode 100644
index 945be7d5b236..000000000000
--- a/Documentation/devicetree/bindings/spi/cadence-quadspi.txt
+++ /dev/null
@@ -1,67 +0,0 @@
-* Cadence Quad SPI controller
-
-Required properties:
-- compatible : should be one of the following:
-	Generic default - "cdns,qspi-nor".
-	For TI 66AK2G SoC - "ti,k2g-qspi", "cdns,qspi-nor".
-	For TI AM654 SoC  - "ti,am654-ospi", "cdns,qspi-nor".
-- reg : Contains two entries, each of which is a tuple consisting of a
-	physical address and length. The first entry is the address and
-	length of the controller register set. The second entry is the
-	address and length of the QSPI Controller data area.
-- interrupts : Unit interrupt specifier for the controller interrupt.
-- clocks : phandle to the Quad SPI clock.
-- cdns,fifo-depth : Size of the data FIFO in words.
-- cdns,fifo-width : Bus width of the data FIFO in bytes.
-- cdns,trigger-address : 32-bit indirect AHB trigger address.
-
-Optional properties:
-- cdns,is-decoded-cs : Flag to indicate whether decoder is used or not.
-- cdns,rclk-en : Flag to indicate that QSPI return clock is used to latch
-  the read data rather than the QSPI clock. Make sure that QSPI return
-  clock is populated on the board before using this property.
-
-Optional subnodes:
-Subnodes of the Cadence Quad SPI controller are spi slave nodes with additional
-custom properties:
-- cdns,read-delay : Delay for read capture logic, in clock cycles
-- cdns,tshsl-ns : Delay in nanoseconds for the length that the master
-                  mode chip select outputs are de-asserted between
-		  transactions.
-- cdns,tsd2d-ns : Delay in nanoseconds between one chip select being
-                  de-activated and the activation of another.
-- cdns,tchsh-ns : Delay in nanoseconds between last bit of current
-                  transaction and deasserting the device chip select
-		  (qspi_n_ss_out).
-- cdns,tslch-ns : Delay in nanoseconds between setting qspi_n_ss_out low
-                  and first bit transfer.
-- resets	: Must contain an entry for each entry in reset-names.
-		  See ../reset/reset.txt for details.
-- reset-names	: Must include either "qspi" and/or "qspi-ocp".
-
-Example:
-
-	qspi: spi@ff705000 {
-		compatible = "cdns,qspi-nor";
-		#address-cells = <1>;
-		#size-cells = <0>;
-		reg = <0xff705000 0x1000>,
-		      <0xffa00000 0x1000>;
-		interrupts = <0 151 4>;
-		clocks = <&qspi_clk>;
-		cdns,is-decoded-cs;
-		cdns,fifo-depth = <128>;
-		cdns,fifo-width = <4>;
-		cdns,trigger-address = <0x00000000>;
-		resets = <&rst QSPI_RESET>, <&rst QSPI_OCP_RESET>;
-		reset-names = "qspi", "qspi-ocp";
-
-		flash0: n25q00@0 {
-			...
-			cdns,read-delay = <4>;
-			cdns,tshsl-ns = <50>;
-			cdns,tsd2d-ns = <50>;
-			cdns,tchsh-ns = <4>;
-			cdns,tslch-ns = <4>;
-		};
-	};
diff --git a/Documentation/devicetree/bindings/spi/cdns,qspi-nor.yaml b/Documentation/devicetree/bindings/spi/cdns,qspi-nor.yaml
new file mode 100644
index 000000000000..5fc54182ed74
--- /dev/null
+++ b/Documentation/devicetree/bindings/spi/cdns,qspi-nor.yaml
@@ -0,0 +1,147 @@
+# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/spi/cdns,qspi-nor.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Cadence Quad SPI controller
+
+maintainers:
+  - Vadivel Murugan <vadivel.muruganx.ramuthevar@xxxxxxxxx>
+
+allOf:
+  - $ref: spi-controller.yaml#
+
+properties:
+  compatible:
+    items:
+      - enum:
+          - cdns,qspi-nor
+          - ti,k2g-qspi
+          - ti,am654-ospi
+
+  reg:
+    items:
+      - description: the controller register set
+      - description: the controller data area
+
+  interrupts:
+    maxItems: 1
+
+  clocks:
+    maxItems: 1
+
+  cdns,fifo-depth:
+    description:
+      Size of the data FIFO in words.
+    $ref: "/schemas/types.yaml#/definitions/uint32"
+    enum: [ 128, 256 ]
+    default: 128
+
+  cdns,fifo-width:
+    $ref: /schemas/types.yaml#/definitions/uint32
+    description:
+      Bus width of the data FIFO in bytes.
+    default: 4
+
+  cdns,trigger-address:
+    $ref: /schemas/types.yaml#/definitions/uint32
+    description:
+      32-bit indirect AHB trigger address.
+
+  cdns,is-decoded-cs:
+    type: boolean
+    description:
+      Flag to indicate whether decoder is used to select different chip select
+      for different memory regions.
+
+  cdns,rclk-en:
+    type: boolean
+    description:
+      Flag to indicate that QSPI return clock is used to latch the read
+      data rather than the QSPI clock. Make sure that QSPI return clock
+      is populated on the board before using this property.
+
+  resets:
+    maxItems: 2
+
+  reset-names:
+    minItems: 1
+    maxItems: 2
+    items:
+      enum: [ qspi, qspi-ocp ]
+
+# subnode's properties
+patternProperties:
+  "@[0-9a-f]+$":
+    type: object
+    description:
+      flash device uses the subnodes below defined properties.
+    properties:
+      cdns,read-delay:
+        $ref: /schemas/types.yaml#/definitions/uint32
+        description:
+          Delay for read capture logic, in clock cycles.
+
+      cdns,tshsl-ns:
+        description:
+          Delay in nanoseconds for the length that the master mode chip select
+          outputs are de-asserted between transactions.
+
+      cdns,tsd2d-ns:
+        description:
+          Delay in nanoseconds between one chip select being de-activated
+          and the activation of another.
+
+      cdns,tchsh-ns:
+        description:
+          Delay in nanoseconds between last bit of current transaction and
+          deasserting the device chip select (qspi_n_ss_out).
+
+      cdns,tslch-ns:
+        description:
+          Delay in nanoseconds between setting qspi_n_ss_out low and
+          first bit transfer.
+
+required:
+  - compatible
+  - reg
+  - interrupts
+  - clocks
+  - cdns,fifo-depth
+  - cdns,fifo-width
+  - cdns,trigger-address
+  - resets
+  - reset-names
+  - '#address-cells'
+  - '#size-cells'
+
+unevaluatedProperties: false
+
+examples:
+  - |
+    qspi: spi@ff705000 {
+      compatible = "cdns,qspi-nor";
+      #address-cells = <1>;
+      #size-cells = <0>;
+      reg = <0xff705000 0x1000>,
+            <0xffa00000 0x1000>;
+      interrupts = <0 151 4>;
+      clocks = <&qspi_clk>;
+      cdns,fifo-depth = <128>;
+      cdns,fifo-width = <4>;
+      cdns,trigger-address = <0x00000000>;
+      resets = <&rst 0x1>, <&rst 0x2>;
+      reset-names = "qspi", "qspi-ocp";
+
+      flash@0 {
+              compatible = "jedec,spi-nor";
+              reg = <0x0>;
+              cdns,read-delay = <4>;
+              cdns,tshsl-ns = <50>;
+              cdns,tsd2d-ns = <50>;
+              cdns,tchsh-ns = <4>;
+              cdns,tslch-ns = <4>;
+     };
+
+    };
-- 
2.11.0




[Index of Archives]     [Device Tree Compilter]     [Device Tree Spec]     [Linux Driver Backports]     [Video for Linux]     [Linux USB Devel]     [Linux PCI Devel]     [Linux Audio Users]     [Linux Kernel]     [Linux SCSI]     [XFree86]     [Yosemite Backpacking]


  Powered by Linux