Re: [PATCH 0/5] mtd: rawnand: qcom: Add support for QSPI nand

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



Hello,

mdalam@xxxxxxxxxxxxxx wrote on Wed, 28 Oct 2020 23:54:23 +0530:

> On 2020-10-28 15:18, Miquel Raynal wrote:
> > Hello,
> > 
> > Md Sadre Alam <mdalam@xxxxxxxxxxxxxx> wrote on Sat, 10 Oct 2020
> > 11:01:37 +0530:
> >   
> >> QPIC 2.0 supports Serial NAND support in addition to all features and
> >> commands in QPIC 1.0 for parallel NAND. Parallel and Serial NAND >> cannot
> >> operate simultaneously. QSPI nand devices will connect to QPIC >> IO_MACRO
> >> block of QPIC controller. There is a separate IO_MACRO clock for >> IO_MACRO
> >> block. Default IO_MACRO block divide the input clock by 4. so if >> IO_MACRO
> >> input clock is 320MHz then on bus it will be 80MHz, so QSPI nand >> device
> >> should also support this frequency.  
> >> >> QPIC provides 4 data pins to QSPI nand. In standard SPI mode (x1 mode) >> data  
> >> transfer will occur on only 2 pins one pin for Serial data in and one >> for
> >> serial data out. In QUAD SPI mode (x4 mode) data transfer will occur >> at all
> >> the four data lines. QPIC controller supports command for x1 mode and >> x4 mode.  
> >> >> Md Sadre Alam (5):  
> >>   dt-bindings: qcom_nandc: IPQ5018 QPIC NAND documentation
> >>   mtd: rawnand: qcom: Add initial support for qspi nand
> >>   mtd: rawnand: qcom: Read QPIC version
> >>   mtd: rawnand: qcom: Enable support for erase,read & write for serial
> >>     nand.
> >>   mtd: rawnand: qcom: Add support for serial training.  
> >> >>  .../devicetree/bindings/mtd/qcom_nandc.txt         |   3 +  
> >>  drivers/mtd/nand/raw/nand_ids.c                    |  13 +
> >>  drivers/mtd/nand/raw/qcom_nandc.c                  | 502 >> ++++++++++++++++++++-
> >>  3 files changed, 494 insertions(+), 24 deletions(-)  
> >> > > I'm sorry but this series clearly breaks the current layering. I cannot  
> > authorize SPI-NAND code to fall into the raw NAND subsystem.
> >   
> 
> I am agree with you, we should not add SPI-NAND changes inside
> raw NAND subsystem.
> 
> > As both typologies cannot be used at the same time, I guess you should
> > have another driver handling this feature under the spi/ subsystem +
> > a few declarations in the SPI-NAND devices list.
> >   
> 
> Initially I was started writing separate driver under SPI-NAND subsystem then I
> realized that more than 85% of raw/qcom_nand.c code getting duplicated.
> 
> That's why I have added this SPI-NAND change in raw/qcom_nand.c since
> more than 85% of code will be reused.
> 
> If I will add this change inside SPI-NAND subsystem then much of
> raw/qcom_nand.c code will get duplicated. Would it be ok ?

What about moving the generic code to drivers/mtd/nand/common/ and
referring to it from drivers/mtd/nand/raw/qcom_nand.c and
drivers/spi/spi-qcom.c (or such)?

Thanks,
Miquèl



[Index of Archives]     [Device Tree Compilter]     [Device Tree Spec]     [Linux Driver Backports]     [Video for Linux]     [Linux USB Devel]     [Linux PCI Devel]     [Linux Audio Users]     [Linux Kernel]     [Linux SCSI]     [XFree86]     [Yosemite Backpacking]


  Powered by Linux