This converts the Armel MXT touchscreen bindings to YAML
format and extends them with the following two properties:
- vdda-supply: the optional analog supply voltage
- vdd-supply: the optional digital supply voltage
I also explained about the reset-gpios property that this
better be flagged as active high (0) despite actually
being active low, because all current device trees and
drivers assume that this is the case and will actively
drive the line low to assert RESET.
Tested the schema with all in-tree users and they verify
fine.
Cc: Nick Dyer <nick@xxxxxxxxxxxxx>
Cc: Stephan Gerhold <stephan@xxxxxxxxxxx>
Cc: devicetree@xxxxxxxxxxxxxxx
Signed-off-by: Linus Walleij <linus.walleij@xxxxxxxxxx>
---
.../bindings/input/atmel,maxtouch.txt | 41 ---------
.../bindings/input/atmel,maxtouch.yaml | 83 +++++++++++++++++++
MAINTAINERS | 2 +-
3 files changed, 84 insertions(+), 42 deletions(-)
delete mode 100644 Documentation/devicetree/bindings/input/atmel,maxtouch.txt
create mode 100644 Documentation/devicetree/bindings/input/atmel,maxtouch.yaml
diff --git a/Documentation/devicetree/bindings/input/atmel,maxtouch.txt b/Documentation/devicetree/bindings/input/atmel,maxtouch.txt
deleted file mode 100644
index c88919480d37..000000000000
--- a/Documentation/devicetree/bindings/input/atmel,maxtouch.txt
+++ /dev/null
@@ -1,41 +0,0 @@
-Atmel maXTouch touchscreen/touchpad
-
-Required properties:
-- compatible:
- atmel,maxtouch
-
- The following compatibles have been used in various products but are
- deprecated:
- atmel,qt602240_ts
- atmel,atmel_mxt_ts
- atmel,atmel_mxt_tp
- atmel,mXT224
-
-- reg: The I2C address of the device
-
-- interrupts: The sink for the touchpad's IRQ output
- See ../interrupt-controller/interrupts.txt
-
-Optional properties for main touchpad device:
-
-- linux,gpio-keymap: When enabled, the SPT_GPIOPWN_T19 object sends messages
- on GPIO bit changes. An array of up to 8 entries can be provided
- indicating the Linux keycode mapped to each bit of the status byte,
- starting at the LSB. Linux keycodes are defined in
- <dt-bindings/input/input.h>.
-
- Note: the numbering of the GPIOs and the bit they start at varies between
- maXTouch devices. You must either refer to the documentation, or
- experiment to determine which bit corresponds to which input. Use
- KEY_RESERVED for unused padding values.
-
-- reset-gpios: GPIO specifier for the touchscreen's reset pin (active low)
-
-Example:
-
- touch@4b {
- compatible = "atmel,maxtouch";
- reg = <0x4b>;
- interrupt-parent = <&gpio>;
- interrupts = <TEGRA_GPIO(W, 3) IRQ_TYPE_LEVEL_LOW>;
- };
diff --git a/Documentation/devicetree/bindings/input/atmel,maxtouch.yaml b/Documentation/devicetree/bindings/input/atmel,maxtouch.yaml
new file mode 100644
index 000000000000..6173562f328a
--- /dev/null
+++ b/Documentation/devicetree/bindings/input/atmel,maxtouch.yaml
@@ -0,0 +1,83 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/input/atmel,maxtouch.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Atmel maXTouch touchscreen/touchpad
+
+maintainers:
+ - Nick Dyer <nick@xxxxxxxxxxxxx>
+ - Linus Walleij <linus.walleij@xxxxxxxxxx>
+
+description: |
+ Atmel maXTouch touchscreen or touchpads such as the mXT244
+ and similar devices.
+
+properties:
+ compatible:
+ const: atmel,maxtouch
+
+ reg:
+ maxItems: 1
+
+ interrupts:
+ maxItems: 1
+
+ vdda-supply:
+ description:
+ Optional regulator for the AVDD analog voltage.
+
+ vdd-supply:
+ description:
+ Optional regulator for the VDD digital voltage.
+
+ reset-gpios:
+ maxItems: 1
+ description:
+ Optional GPIO specifier for the touchscreen's reset pin
+ (active low). The operating system should actively drive
+ the line low to assert reset, so the line must NOT be
+ flagged with GPIO_ACTIVE_LOW, it should (counterintuitively)
+ be set to GPIO_ACTIVE_HIGH.
+
+ linux,gpio-keymap:
+ $ref: /schemas/types.yaml#/definitions/uint32-array
+ description: |
+ When enabled, the SPT_GPIOPWN_T19 object sends messages
+ on GPIO bit changes. An array of up to 8 entries can be provided
+ indicating the Linux keycode mapped to each bit of the status byte,
+ starting at the LSB. Linux keycodes are defined in
+ <dt-bindings/input/input.h>.
+
+ Note: the numbering of the GPIOs and the bit they start at varies
+ between maXTouch devices. You must either refer to the documentation,
+ or experiment to determine which bit corresponds to which input. Use
+ KEY_RESERVED for unused padding values.
+
+required:
+ - compatible
+ - reg
+ - interrupts
+
+additionalProperties: false
+
+examples:
+ - |
+ #include <dt-bindings/interrupt-controller/irq.h>
+ #include <dt-bindings/gpio/gpio.h>
+ i2c {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ touchscreen@4a {
+ compatible = "atmel,maxtouch";
+ reg = <0x4a>;
+ interrupt-parent = <&gpio>;
+ interrupts = <26 IRQ_TYPE_EDGE_FALLING>;
+ reset-gpios = <&gpio 27 GPIO_ACTIVE_HIGH>;
+ vdda-supply = <&ab8500_ldo_aux2_reg>;
+ vdd-supply = <&ab8500_ldo_aux5_reg>;
+ };
+ };
+
+...
diff --git a/MAINTAINERS b/MAINTAINERS
index e73636b75f29..b4b46fcb82db 100644
--- a/MAINTAINERS
+++ b/MAINTAINERS
@@ -2966,7 +2966,7 @@ ATMEL MAXTOUCH DRIVER
M: Nick Dyer <nick@xxxxxxxxxxxxx>
S: Maintained
T: git git://github.com/ndyer/linux.git
-F: Documentation/devicetree/bindings/input/atmel,maxtouch.txt
+F: Documentation/devicetree/bindings/input/atmel,maxtouch.yaml
F: drivers/input/touchscreen/atmel_mxt_ts.c
ATMEL WIRELESS DRIVER
--
2.26.2
