[PATCH v3 2/3] drm/bridge: sii902x: Enable I/O and core VCC supplies if present

[Alexandru Gagniuc <mr.nuke.me@xxxxxxxxx>]

On the SII9022, the IOVCC and CVCC12 supplies must reach the correct
voltage before the reset sequence is initiated. On most boards, this
assumption is true at boot-up, so initialization succeeds.

However, when we try to initialize the chip with incorrect supply
voltages, it will not respond to I2C requests. sii902x_probe() fails
with -ENXIO.

To resolve this, look for the "iovcc" and "cvcc12" regulators, and
make sure they are enabled before starting the reset sequence. If
these supplies are not available in devicetree, then they will default
to dummy-regulator. In that case everything will work like before.

This was observed on a STM32MP157C-DK2 booting in u-boot falcon mode.
On this board, the supplies would be set by the second stage
bootloader, which does not run in falcon mode.

Signed-off-by: Alexandru Gagniuc <mr.nuke.me@xxxxxxxxx>
---
Changes since v1:
  * Fix return code after regulator_enable(sii902x->iovcc) fails (Fabio Estevam)
  * Use dev_err_probe() instead of dev_err() where appropriate (Sam Ravnborg)

Changes since v2:
  * Eliminate prototype for static functionn sii902x_init (Sam Ravnborg)
  * Bundled supplies under regulator_bulk_get/enable/disable()
  
 drivers/gpu/drm/bridge/sii902x.c | 23 +++++++++++++++++++++++
 1 file changed, 23 insertions(+)

diff --git a/drivers/gpu/drm/bridge/sii902x.c b/drivers/gpu/drm/bridge/sii902x.c
index f78c17f49887..5bab51a6b55c 100644
--- a/drivers/gpu/drm/bridge/sii902x.c
+++ b/drivers/gpu/drm/bridge/sii902x.c
@@ -17,6 +17,7 @@
 #include <linux/i2c.h>
 #include <linux/module.h>
 #include <linux/regmap.h>
+#include <linux/regulator/consumer.h>
 #include <linux/clk.h>
 
 #include <drm/drm_atomic_helper.h>
@@ -168,6 +169,7 @@ struct sii902x {
 	struct drm_connector connector;
 	struct gpio_desc *reset_gpio;
 	struct i2c_mux_core *i2cmux;
+	struct regulator_bulk_data supplies[2];
 	/*
 	 * Mutex protects audio and video functions from interfering
 	 * each other, by keeping their i2c command sequences atomic.
@@ -1049,7 +1051,26 @@ static int sii902x_probe(struct i2c_client *client,
 
 	mutex_init(&sii902x->mutex);
 
+	sii902x->supplies[0].supply = "iovcc";
+	sii902x->supplies[1].supply = "cvcc12";
+	ret = devm_regulator_bulk_get(dev, ARRAY_SIZE(sii902x->supplies),
+				      sii902x->supplies);
+	if (ret < 0)
+		return ret;
+
+	ret = regulator_bulk_enable(ARRAY_SIZE(sii902x->supplies),
+				    sii902x->supplies);
+	if (ret < 0) {
+		dev_err_probe(dev, ret, "Failed to enable supplies");
+		return ret;
+	}
+
 	ret = sii902x_init(sii902x);
+	if (ret < 0) {
+		regulator_bulk_disable(ARRAY_SIZE(sii902x->supplies),
+					sii902x->supplies);
+	}
+
 	return ret;
 }
 
@@ -1060,6 +1081,8 @@ static int sii902x_remove(struct i2c_client *client)
 
 	i2c_mux_del_adapters(sii902x->i2cmux);
 	drm_bridge_remove(&sii902x->bridge);
+	regulator_bulk_disable(ARRAY_SIZE(sii902x->supplies),
+				sii902x->supplies);
 
 	return 0;
 }
-- 
2.26.2