This commit implements Tegra210 XUSB PADCTL wake and sleepwalk
routines. Sleepwalk logic is in PMC (always-on) hardware block.
PMC driver provides managed access to the sleepwalk registers
via regmap framework.
Signed-off-by: JC Kuo <jckuo@xxxxxxxxxx>
---
v4:
move sleepwalk/wake stubs from 'struct tegra_xusb_padctl_ops' to
'struct tegra_xusb_lane_ops'
remove a blank line
rename 'pmc_dev' with 'pdev'
remove 'struct device_node *np'
rename label 'no_pmc' with 'out'
defer .probe() if PMC driver is yet to load
v3:
rename 'pmc_reg" with 'regmap' and move to the top of 'struct tegra210_xusb_padctl'
change return data of .phy_remote_wake_detected() to 'bool'
change input parameter of .phy_remote_wake_detected() to 'struct phy*'
remove unnecessary 'else'
rename 'val' with 'value'
rename tegra_pmc_*() with tegra210_pmc_*()
remove VBUS ON/OFF control change
drivers/phy/tegra/xusb-tegra210.c | 930 ++++++++++++++++++++++++++++++
1 file changed, 930 insertions(+)
diff --git a/drivers/phy/tegra/xusb-tegra210.c b/drivers/phy/tegra/xusb-tegra210.c
index b038d032fea1..8af73ba78ad7 100644
--- a/drivers/phy/tegra/xusb-tegra210.c
+++ b/drivers/phy/tegra/xusb-tegra210.c
@@ -16,6 +16,8 @@
#include <linux/regulator/consumer.h>
#include <linux/reset.h>
#include <linux/slab.h>
+#include <linux/regmap.h>
+#include <linux/of_platform.h>
#include <soc/tegra/fuse.h>
@@ -52,6 +54,20 @@
#define XUSB_PADCTL_SS_PORT_MAP_PORTX_MAP(x, v) (((v) & 0x7) << ((x) * 5))
#define XUSB_PADCTL_SS_PORT_MAP_PORT_DISABLED 0x7
+#define XUSB_PADCTL_ELPG_PROGRAM_0 0x20
+#define USB2_PORT_WAKE_INTERRUPT_ENABLE(x) BIT((x))
+#define USB2_PORT_WAKEUP_EVENT(x) BIT((x) + 7)
+#define SS_PORT_WAKE_INTERRUPT_ENABLE(x) BIT((x) + 14)
+#define SS_PORT_WAKEUP_EVENT(x) BIT((x) + 21)
+#define USB2_HSIC_PORT_WAKE_INTERRUPT_ENABLE(x) BIT((x) + 28)
+#define USB2_HSIC_PORT_WAKEUP_EVENT(x) BIT((x) + 30)
+#define ALL_WAKE_EVENTS ( \
+ USB2_PORT_WAKEUP_EVENT(0) | USB2_PORT_WAKEUP_EVENT(1) | \
+ USB2_PORT_WAKEUP_EVENT(2) | USB2_PORT_WAKEUP_EVENT(3) | \
+ SS_PORT_WAKEUP_EVENT(0) | SS_PORT_WAKEUP_EVENT(1) | \
+ SS_PORT_WAKEUP_EVENT(2) | SS_PORT_WAKEUP_EVENT(3) | \
+ USB2_HSIC_PORT_WAKEUP_EVENT(0))
+
#define XUSB_PADCTL_ELPG_PROGRAM1 0x024
#define XUSB_PADCTL_ELPG_PROGRAM1_AUX_MUX_LP0_VCORE_DOWN (1 << 31)
#define XUSB_PADCTL_ELPG_PROGRAM1_AUX_MUX_LP0_CLAMP_EN_EARLY (1 << 30)
@@ -90,6 +106,8 @@
#define XUSB_PADCTL_USB2_OTG_PAD_CTL1_PD_DR (1 << 2)
#define XUSB_PADCTL_USB2_OTG_PAD_CTL1_PD_DISC_OVRD (1 << 1)
#define XUSB_PADCTL_USB2_OTG_PAD_CTL1_PD_CHRP_OVRD (1 << 0)
+#define RPD_CTRL(x) (((x) & 0x1f) << 26)
+#define RPD_CTRL_VALUE(x) (((x) >> 26) & 0x1f)
#define XUSB_PADCTL_USB2_BIAS_PAD_CTL0 0x284
#define XUSB_PADCTL_USB2_BIAS_PAD_CTL0_PD (1 << 11)
@@ -108,6 +126,8 @@
#define XUSB_PADCTL_USB2_BIAS_PAD_CTL1_TRK_START_TIMER_SHIFT 12
#define XUSB_PADCTL_USB2_BIAS_PAD_CTL1_TRK_START_TIMER_MASK 0x7f
#define XUSB_PADCTL_USB2_BIAS_PAD_CTL1_TRK_START_TIMER_VAL 0x1e
+#define TCTRL_VALUE(x) (((x) & 0x3f) >> 0)
+#define PCTRL_VALUE(x) (((x) >> 6) & 0x3f)
#define XUSB_PADCTL_HSIC_PADX_CTL0(x) (0x300 + (x) * 0x20)
#define XUSB_PADCTL_HSIC_PAD_CTL0_RPU_STROBE (1 << 18)
@@ -251,16 +271,161 @@
#define XUSB_PADCTL_USB2_VBUS_ID_OVERRIDE_FLOATING 8
#define XUSB_PADCTL_USB2_VBUS_ID_OVERRIDE_GROUNDED 0
+/* USB2 SLEEPWALK registers */
+#define UTMIP(_port, _offset1, _offset2) \
+ (((_port) <= 2) ? (_offset1) : (_offset2))
+
+#define PMC_UTMIP_UHSIC_SLEEP_CFG(x) UTMIP(x, 0x1fc, 0x4d0)
+#define UTMIP_MASTER_ENABLE(x) UTMIP(x, BIT(8 * (x)), BIT(0))
+#define UTMIP_FSLS_USE_PMC(x) UTMIP(x, BIT(8 * (x) + 1), \
+ BIT(1))
+#define UTMIP_PCTRL_USE_PMC(x) UTMIP(x, BIT(8 * (x) + 2), \
+ BIT(2))
+#define UTMIP_TCTRL_USE_PMC(x) UTMIP(x, BIT(8 * (x) + 3), \
+ BIT(3))
+#define UTMIP_WAKE_VAL(_port, _value) (((_value) & 0xf) << \
+ (UTMIP(_port, 8 * (_port) + 4, 4)))
+#define UTMIP_WAKE_VAL_NONE(_port) UTMIP_WAKE_VAL(_port, 12)
+#define UTMIP_WAKE_VAL_ANY(_port) UTMIP_WAKE_VAL(_port, 15)
+
+#define PMC_UTMIP_UHSIC_SLEEP_CFG1 (0x4d0)
+#define UTMIP_RPU_SWITC_LOW_USE_PMC_PX(x) BIT((x) + 8)
+#define UTMIP_RPD_CTRL_USE_PMC_PX(x) BIT((x) + 16)
+
+#define PMC_UTMIP_MASTER_CONFIG (0x274)
+#define UTMIP_PWR(x) UTMIP(x, BIT(x), BIT(4))
+#define UHSIC_PWR(x) BIT(3)
+
+#define PMC_USB_DEBOUNCE_DEL (0xec)
+#define DEBOUNCE_VAL(x) (((x) & 0xffff) << 0)
+#define UTMIP_LINE_DEB_CNT(x) (((x) & 0xf) << 16)
+#define UHSIC_LINE_DEB_CNT(x) (((x) & 0xf) << 20)
+
+#define PMC_UTMIP_UHSIC_FAKE(x) UTMIP(x, 0x218, 0x294)
+#define UTMIP_FAKE_USBOP_VAL(x) UTMIP(x, BIT(4 * (x)), BIT(8))
+#define UTMIP_FAKE_USBON_VAL(x) UTMIP(x, BIT(4 * (x) + 1), \
+ BIT(9))
+#define UTMIP_FAKE_USBOP_EN(x) UTMIP(x, BIT(4 * (x) + 2), \
+ BIT(10))
+#define UTMIP_FAKE_USBON_EN(x) UTMIP(x, BIT(4 * (x) + 3), \
+ BIT(11))
+
+#define PMC_UTMIP_UHSIC_SLEEPWALK_CFG(x) UTMIP(x, 0x200, 0x288)
+#define UTMIP_LINEVAL_WALK_EN(x) UTMIP(x, BIT(8 * (x) + 7), \
+ BIT(15))
+
+#define PMC_USB_AO (0xf0)
+#define USBOP_VAL_PD(x) UTMIP(x, BIT(4 * (x)), BIT(20))
+#define USBON_VAL_PD(x) UTMIP(x, BIT(4 * (x) + 1), \
+ BIT(21))
+#define STROBE_VAL_PD(x) BIT(12)
+#define DATA0_VAL_PD(x) BIT(13)
+#define DATA1_VAL_PD BIT(24)
+
+#define PMC_UTMIP_UHSIC_SAVED_STATE(x) UTMIP(x, 0x1f0, 0x280)
+#define SPEED(_port, _value) (((_value) & 0x3) << \
+ (UTMIP(_port, 8 * (_port), 8)))
+#define UTMI_HS(_port) SPEED(_port, 0)
+#define UTMI_FS(_port) SPEED(_port, 1)
+#define UTMI_LS(_port) SPEED(_port, 2)
+#define UTMI_RST(_port) SPEED(_port, 3)
+
+#define PMC_UTMIP_UHSIC_TRIGGERS (0x1ec)
+#define UTMIP_CLR_WALK_PTR(x) UTMIP(x, BIT(x), BIT(16))
+#define UTMIP_CAP_CFG(x) UTMIP(x, BIT((x) + 4), BIT(17))
+#define UTMIP_CLR_WAKE_ALARM(x) UTMIP(x, BIT((x) + 12), \
+ BIT(19))
+#define UHSIC_CLR_WALK_PTR BIT(3)
+#define UHSIC_CLR_WAKE_ALARM BIT(15)
+
+#define PMC_UTMIP_SLEEPWALK_PX(x) UTMIP(x, 0x204 + (4 * (x)), \
+ 0x4e0)
+/* phase A */
+#define UTMIP_USBOP_RPD_A BIT(0)
+#define UTMIP_USBON_RPD_A BIT(1)
+#define UTMIP_AP_A BIT(4)
+#define UTMIP_AN_A BIT(5)
+#define UTMIP_HIGHZ_A BIT(6)
+/* phase B */
+#define UTMIP_USBOP_RPD_B BIT(8)
+#define UTMIP_USBON_RPD_B BIT(9)
+#define UTMIP_AP_B BIT(12)
+#define UTMIP_AN_B BIT(13)
+#define UTMIP_HIGHZ_B BIT(14)
+/* phase C */
+#define UTMIP_USBOP_RPD_C BIT(16)
+#define UTMIP_USBON_RPD_C BIT(17)
+#define UTMIP_AP_C BIT(20)
+#define UTMIP_AN_C BIT(21)
+#define UTMIP_HIGHZ_C BIT(22)
+/* phase D */
+#define UTMIP_USBOP_RPD_D BIT(24)
+#define UTMIP_USBON_RPD_D BIT(25)
+#define UTMIP_AP_D BIT(28)
+#define UTMIP_AN_D BIT(29)
+#define UTMIP_HIGHZ_D BIT(30)
+
+#define PMC_UTMIP_UHSIC_LINE_WAKEUP (0x26c)
+#define UTMIP_LINE_WAKEUP_EN(x) UTMIP(x, BIT(x), BIT(4))
+#define UHSIC_LINE_WAKEUP_EN BIT(3)
+
+#define PMC_UTMIP_TERM_PAD_CFG (0x1f8)
+#define PCTRL_VAL(x) (((x) & 0x3f) << 1)
+#define TCTRL_VAL(x) (((x) & 0x3f) << 7)
+
+#define PMC_UTMIP_PAD_CFGX(x) (0x4c0 + (4 * (x)))
+#define RPD_CTRL_PX(x) (((x) & 0x1f) << 22)
+
+#define PMC_UHSIC_SLEEP_CFG PMC_UTMIP_UHSIC_SLEEP_CFG(0)
+#define UHSIC_MASTER_ENABLE BIT(24)
+#define UHSIC_WAKE_VAL(_value) (((_value) & 0xf) << 28)
+#define UHSIC_WAKE_VAL_SD10 UHSIC_WAKE_VAL(2)
+#define UHSIC_WAKE_VAL_NONE UHSIC_WAKE_VAL(12)
+
+#define PMC_UHSIC_FAKE PMC_UTMIP_UHSIC_FAKE(0)
+#define UHSIC_FAKE_STROBE_VAL BIT(12)
+#define UHSIC_FAKE_DATA_VAL BIT(13)
+#define UHSIC_FAKE_STROBE_EN BIT(14)
+#define UHSIC_FAKE_DATA_EN BIT(15)
+
+#define PMC_UHSIC_SAVED_STATE PMC_UTMIP_UHSIC_SAVED_STATE(0)
+#define UHSIC_MODE(_value) (((_value) & 0x1) << 24)
+#define UHSIC_HS UHSIC_MODE(0)
+#define UHSIC_RST UHSIC_MODE(1)
+
+#define PMC_UHSIC_SLEEPWALK_CFG PMC_UTMIP_UHSIC_SLEEPWALK_CFG(0)
+#define UHSIC_WAKE_WALK_EN BIT(30)
+#define UHSIC_LINEVAL_WALK_EN BIT(31)
+
+#define PMC_UHSIC_SLEEPWALK_P0 (0x210)
+#define UHSIC_DATA0_RPD_A BIT(1)
+#define UHSIC_DATA0_RPU_B BIT(11)
+#define UHSIC_DATA0_RPU_C BIT(19)
+#define UHSIC_DATA0_RPU_D BIT(27)
+#define UHSIC_STROBE_RPU_A BIT(2)
+#define UHSIC_STROBE_RPD_B BIT(8)
+#define UHSIC_STROBE_RPD_C BIT(16)
+#define UHSIC_STROBE_RPD_D BIT(24)
+
struct tegra210_xusb_fuse_calibration {
u32 hs_curr_level[4];
u32 hs_term_range_adj;
u32 rpd_ctrl;
};
+struct tegra210_xusb_padctl_context {
+ u32 usb2_pad_mux;
+ u32 usb2_port_cap;
+ u32 ss_port_map;
+ u32 usb3_pad_mux;
+};
+
struct tegra210_xusb_padctl {
struct tegra_xusb_padctl base;
+ struct regmap *regmap;
struct tegra210_xusb_fuse_calibration fuse;
+ struct tegra210_xusb_padctl_context context;
};
static inline struct tegra210_xusb_padctl *
@@ -890,6 +1055,663 @@ static int tegra210_hsic_set_idle(struct tegra_xusb_padctl *padctl,
return 0;
}
+static int tegra210_usb3_enable_phy_sleepwalk(struct tegra_xusb_lane *lane,
+ enum usb_device_speed speed)
+{
+ struct tegra_xusb_padctl *padctl = lane->pad->padctl;
+ int port = tegra210_usb3_lane_map(lane);
+ struct device *dev = padctl->dev;
+ u32 value;
+
+ if (port < 0) {
+ dev_err(dev, "invalid usb3 port number\n");
+ return -EINVAL;
+ }
+
+ dev_dbg(dev, "phy enable sleepwalk usb3 %d\n", port);
+
+ mutex_lock(&padctl->lock);
+
+ value = padctl_readl(padctl, XUSB_PADCTL_ELPG_PROGRAM1);
+ value |= XUSB_PADCTL_ELPG_PROGRAM1_SSPX_ELPG_CLAMP_EN_EARLY(port);
+ padctl_writel(padctl, value, XUSB_PADCTL_ELPG_PROGRAM1);
+
+ usleep_range(100, 200);
+
+ value = padctl_readl(padctl, XUSB_PADCTL_ELPG_PROGRAM1);
+ value |= XUSB_PADCTL_ELPG_PROGRAM1_SSPX_ELPG_CLAMP_EN(port);
+ padctl_writel(padctl, value, XUSB_PADCTL_ELPG_PROGRAM1);
+
+ usleep_range(250, 350);
+
+ mutex_unlock(&padctl->lock);
+
+ return 0;
+}
+
+static int tegra210_usb3_disable_phy_sleepwalk(struct tegra_xusb_lane *lane)
+{
+ struct tegra_xusb_padctl *padctl = lane->pad->padctl;
+ int port = tegra210_usb3_lane_map(lane);
+ struct device *dev = padctl->dev;
+ u32 value;
+
+ if (port < 0) {
+ dev_err(dev, "invalid usb3 port number\n");
+ return -EINVAL;
+ }
+
+ dev_dbg(dev, "phy disable sleepwalk usb3 %d\n", port);
+
+ mutex_lock(&padctl->lock);
+
+ value = padctl_readl(padctl, XUSB_PADCTL_ELPG_PROGRAM1);
+ value &= ~XUSB_PADCTL_ELPG_PROGRAM1_SSPX_ELPG_CLAMP_EN_EARLY(port);
+ padctl_writel(padctl, value, XUSB_PADCTL_ELPG_PROGRAM1);
+
+ usleep_range(100, 200);
+
+ value = padctl_readl(padctl, XUSB_PADCTL_ELPG_PROGRAM1);
+ value &= ~XUSB_PADCTL_ELPG_PROGRAM1_SSPX_ELPG_CLAMP_EN(port);
+ padctl_writel(padctl, value, XUSB_PADCTL_ELPG_PROGRAM1);
+
+ mutex_unlock(&padctl->lock);
+
+ return 0;
+}
+
+static int tegra210_usb3_enable_phy_wake(struct tegra_xusb_lane *lane)
+{
+ struct tegra_xusb_padctl *padctl = lane->pad->padctl;
+ int port = tegra210_usb3_lane_map(lane);
+ struct device *dev = padctl->dev;
+ u32 value;
+
+ if (port < 0) {
+ dev_err(dev, "invalid usb3 port number\n");
+ return -EINVAL;
+ }
+
+ dev_dbg(dev, "phy enable wake usb3 %d\n", port);
+
+ mutex_lock(&padctl->lock);
+
+ value = padctl_readl(padctl, XUSB_PADCTL_ELPG_PROGRAM_0);
+ value &= ~ALL_WAKE_EVENTS;
+ value |= SS_PORT_WAKEUP_EVENT(port);
+ padctl_writel(padctl, value, XUSB_PADCTL_ELPG_PROGRAM_0);
+
+ usleep_range(10, 20);
+
+ value = padctl_readl(padctl, XUSB_PADCTL_ELPG_PROGRAM_0);
+ value &= ~ALL_WAKE_EVENTS;
+ value |= SS_PORT_WAKE_INTERRUPT_ENABLE(port);
+ padctl_writel(padctl, value, XUSB_PADCTL_ELPG_PROGRAM_0);
+
+ mutex_unlock(&padctl->lock);
+
+ return 0;
+}
+
+static int tegra210_usb3_disable_phy_wake(struct tegra_xusb_lane *lane)
+{
+ struct tegra_xusb_padctl *padctl = lane->pad->padctl;
+ int port = tegra210_usb3_lane_map(lane);
+ struct device *dev = padctl->dev;
+ u32 value;
+
+ if (port < 0) {
+ dev_err(dev, "invalid usb3 port number\n");
+ return -EINVAL;
+ }
+
+ dev_dbg(dev, "phy disable wake usb3 %d\n", port);
+
+ mutex_lock(&padctl->lock);
+
+ value = padctl_readl(padctl, XUSB_PADCTL_ELPG_PROGRAM_0);
+ value &= ~ALL_WAKE_EVENTS;
+ value &= ~SS_PORT_WAKE_INTERRUPT_ENABLE(port);
+ padctl_writel(padctl, value, XUSB_PADCTL_ELPG_PROGRAM_0);
+
+ usleep_range(10, 20);
+
+ value = padctl_readl(padctl, XUSB_PADCTL_ELPG_PROGRAM_0);
+ value &= ~ALL_WAKE_EVENTS;
+ value |= SS_PORT_WAKEUP_EVENT(port);
+ padctl_writel(padctl, value, XUSB_PADCTL_ELPG_PROGRAM_0);
+
+ mutex_unlock(&padctl->lock);
+
+ return 0;
+}
+
+static bool tegra210_usb3_phy_remote_wake_detected(struct tegra_xusb_lane *lane)
+{
+ struct tegra_xusb_padctl *padctl = lane->pad->padctl;
+ int index = tegra210_usb3_lane_map(lane);
+ u32 value;
+
+ if (index < 0)
+ return false;
+
+ value = padctl_readl(padctl, XUSB_PADCTL_ELPG_PROGRAM_0);
+ if ((value & SS_PORT_WAKE_INTERRUPT_ENABLE(index)) && (value & SS_PORT_WAKEUP_EVENT(index)))
+ return true;
+
+ return false;
+}
+
+static int tegra210_utmi_enable_phy_wake(struct tegra_xusb_lane *lane)
+{
+ struct tegra_xusb_padctl *padctl = lane->pad->padctl;
+ unsigned int index = lane->index;
+ struct device *dev = padctl->dev;
+ u32 value;
+
+ dev_dbg(dev, "phy enable wake on usb2 %d\n", index);
+
+ mutex_lock(&padctl->lock);
+
+ value = padctl_readl(padctl, XUSB_PADCTL_ELPG_PROGRAM_0);
+ value &= ~ALL_WAKE_EVENTS;
+ value |= USB2_PORT_WAKEUP_EVENT(index);
+ padctl_writel(padctl, value, XUSB_PADCTL_ELPG_PROGRAM_0);
+
+ usleep_range(10, 20);
+
+ value = padctl_readl(padctl, XUSB_PADCTL_ELPG_PROGRAM_0);
+ value &= ~ALL_WAKE_EVENTS;
+ value |= USB2_PORT_WAKE_INTERRUPT_ENABLE(index);
+ padctl_writel(padctl, value, XUSB_PADCTL_ELPG_PROGRAM_0);
+
+ mutex_unlock(&padctl->lock);
+
+ return 0;
+}
+
+static int tegra210_utmi_disable_phy_wake(struct tegra_xusb_lane *lane)
+{
+ struct tegra_xusb_padctl *padctl = lane->pad->padctl;
+ unsigned int index = lane->index;
+ struct device *dev = padctl->dev;
+ u32 value;
+
+ dev_dbg(dev, "phy disable wake on usb2 %d\n", index);
+
+ mutex_lock(&padctl->lock);
+
+ value = padctl_readl(padctl, XUSB_PADCTL_ELPG_PROGRAM_0);
+ value &= ~ALL_WAKE_EVENTS;
+ value &= ~USB2_PORT_WAKE_INTERRUPT_ENABLE(index);
+ padctl_writel(padctl, value, XUSB_PADCTL_ELPG_PROGRAM_0);
+
+ usleep_range(10, 20);
+
+ value = padctl_readl(padctl, XUSB_PADCTL_ELPG_PROGRAM_0);
+ value &= ~ALL_WAKE_EVENTS;
+ value |= USB2_PORT_WAKEUP_EVENT(index);
+ padctl_writel(padctl, value, XUSB_PADCTL_ELPG_PROGRAM_0);
+
+ mutex_unlock(&padctl->lock);
+
+ return 0;
+}
+
+static bool tegra210_utmi_phy_remote_wake_detected(struct tegra_xusb_lane *lane)
+{
+ struct tegra_xusb_padctl *padctl = lane->pad->padctl;
+ unsigned int index = lane->index;
+ u32 value;
+
+ value = padctl_readl(padctl, XUSB_PADCTL_ELPG_PROGRAM_0);
+ if ((value & USB2_PORT_WAKE_INTERRUPT_ENABLE(index)) &&
+ (value & USB2_PORT_WAKEUP_EVENT(index)))
+ return true;
+
+ return false;
+}
+
+static int tegra210_hsic_enable_phy_wake(struct tegra_xusb_lane *lane)
+{
+ struct tegra_xusb_padctl *padctl = lane->pad->padctl;
+ unsigned int index = lane->index;
+ struct device *dev = padctl->dev;
+ u32 value;
+
+ dev_dbg(dev, "phy enable wake on hsic %d\n", index);
+
+ mutex_lock(&padctl->lock);
+
+ value = padctl_readl(padctl, XUSB_PADCTL_ELPG_PROGRAM_0);
+ value &= ~ALL_WAKE_EVENTS;
+ value |= USB2_HSIC_PORT_WAKEUP_EVENT(index);
+ padctl_writel(padctl, value, XUSB_PADCTL_ELPG_PROGRAM_0);
+
+ usleep_range(10, 20);
+
+ value = padctl_readl(padctl, XUSB_PADCTL_ELPG_PROGRAM_0);
+ value &= ~ALL_WAKE_EVENTS;
+ value |= USB2_HSIC_PORT_WAKE_INTERRUPT_ENABLE(index);
+ padctl_writel(padctl, value, XUSB_PADCTL_ELPG_PROGRAM_0);
+
+ mutex_unlock(&padctl->lock);
+
+ return 0;
+}
+
+static int tegra210_hsic_disable_phy_wake(struct tegra_xusb_lane *lane)
+{
+ struct tegra_xusb_padctl *padctl = lane->pad->padctl;
+ unsigned int index = lane->index;
+ struct device *dev = padctl->dev;
+ u32 value;
+
+ dev_dbg(dev, "phy disable wake on hsic %d\n", index);
+
+ mutex_lock(&padctl->lock);
+
+ value = padctl_readl(padctl, XUSB_PADCTL_ELPG_PROGRAM_0);
+ value &= ~ALL_WAKE_EVENTS;
+ value &= ~USB2_HSIC_PORT_WAKE_INTERRUPT_ENABLE(index);
+ padctl_writel(padctl, value, XUSB_PADCTL_ELPG_PROGRAM_0);
+
+ usleep_range(10, 20);
+
+ value = padctl_readl(padctl, XUSB_PADCTL_ELPG_PROGRAM_0);
+ value &= ~ALL_WAKE_EVENTS;
+ value |= USB2_HSIC_PORT_WAKEUP_EVENT(index);
+ padctl_writel(padctl, value, XUSB_PADCTL_ELPG_PROGRAM_0);
+
+ mutex_unlock(&padctl->lock);
+
+ return 0;
+}
+
+static bool tegra210_hsic_phy_remote_wake_detected(struct tegra_xusb_lane *lane)
+{
+ struct tegra_xusb_padctl *padctl = lane->pad->padctl;
+ unsigned int index = lane->index;
+ u32 value;
+
+ value = padctl_readl(padctl, XUSB_PADCTL_ELPG_PROGRAM_0);
+ if ((value & USB2_HSIC_PORT_WAKE_INTERRUPT_ENABLE(index)) &&
+ (value & USB2_HSIC_PORT_WAKEUP_EVENT(index)))
+ return true;
+
+ return false;
+}
+
+#define padctl_pmc_readl(_priv, _offset) \
+({ \
+ u32 value; \
+ WARN(regmap_read(_priv->regmap, _offset, &value), "read %s failed\n", #_offset);\
+ value; \
+})
+
+#define padctl_pmc_writel(_priv, _value, _offset) \
+ WARN(regmap_write(_priv->regmap, _offset, _value), "write %s failed\n", #_offset)
+
+static int tegra210_pmc_utmi_enable_phy_sleepwalk(struct tegra_xusb_lane *lane,
+ enum usb_device_speed speed)
+{
+ struct tegra_xusb_padctl *padctl = lane->pad->padctl;
+ struct tegra210_xusb_padctl *priv = to_tegra210_xusb_padctl(padctl);
+ struct device *dev = padctl->dev;
+ unsigned int port = lane->index;
+ u32 value, tctrl, pctrl, rpd_ctrl;
+
+ if (!priv->regmap)
+ return -EOPNOTSUPP;
+
+ if (speed > USB_SPEED_HIGH)
+ return -EINVAL;
+
+ dev_dbg(dev, "phy enable sleepwalk usb2 %d speed %d\n", port, speed);
+
+ value = padctl_readl(padctl, XUSB_PADCTL_USB2_BIAS_PAD_CTL1);
+ tctrl = TCTRL_VALUE(value);
+ pctrl = PCTRL_VALUE(value);
+
+ value = padctl_readl(padctl, XUSB_PADCTL_USB2_OTG_PADX_CTL1(port));
+ rpd_ctrl = RPD_CTRL_VALUE(value);
+
+ /* ensure sleepwalk logic is disabled */
+ value = padctl_pmc_readl(priv, PMC_UTMIP_UHSIC_SLEEP_CFG(port));
+ value &= ~UTMIP_MASTER_ENABLE(port);
+ padctl_pmc_writel(priv, value, PMC_UTMIP_UHSIC_SLEEP_CFG(port));
+
+ /* ensure sleepwalk logics are in low power mode */
+ value = padctl_pmc_readl(priv, PMC_UTMIP_MASTER_CONFIG);
+ value |= UTMIP_PWR(port);
+ padctl_pmc_writel(priv, value, PMC_UTMIP_MASTER_CONFIG);
+
+ /* set debounce time */
+ value = padctl_pmc_readl(priv, PMC_USB_DEBOUNCE_DEL);
+ value &= ~UTMIP_LINE_DEB_CNT(~0);
+ value |= UTMIP_LINE_DEB_CNT(0x1);
+ padctl_pmc_writel(priv, value, PMC_USB_DEBOUNCE_DEL);
+
+ /* ensure fake events of sleepwalk logic are desiabled */
+ value = padctl_pmc_readl(priv, PMC_UTMIP_UHSIC_FAKE(port));
+ value &= ~(UTMIP_FAKE_USBOP_VAL(port) | UTMIP_FAKE_USBON_VAL(port) |
+ UTMIP_FAKE_USBOP_EN(port) | UTMIP_FAKE_USBON_EN(port));
+ padctl_pmc_writel(priv, value, PMC_UTMIP_UHSIC_FAKE(port));
+
+ /* ensure wake events of sleepwalk logic are not latched */
+ value = padctl_pmc_readl(priv, PMC_UTMIP_UHSIC_LINE_WAKEUP);
+ value &= ~UTMIP_LINE_WAKEUP_EN(port);
+ padctl_pmc_writel(priv, value, PMC_UTMIP_UHSIC_LINE_WAKEUP);
+
+ /* disable wake event triggers of sleepwalk logic */
+ value = padctl_pmc_readl(priv, PMC_UTMIP_UHSIC_SLEEP_CFG(port));
+ value &= ~UTMIP_WAKE_VAL(port, ~0);
+ value |= UTMIP_WAKE_VAL_NONE(port);
+ padctl_pmc_writel(priv, value, PMC_UTMIP_UHSIC_SLEEP_CFG(port));
+
+ /* power down the line state detectors of the pad */
+ value = padctl_pmc_readl(priv, PMC_USB_AO);
+ value |= (USBOP_VAL_PD(port) | USBON_VAL_PD(port));
+ padctl_pmc_writel(priv, value, PMC_USB_AO);
+
+ /* save state per speed */
+ value = padctl_pmc_readl(priv, PMC_UTMIP_UHSIC_SAVED_STATE(port));
+ value &= ~SPEED(port, ~0);
+ if (speed == USB_SPEED_HIGH)
+ value |= UTMI_HS(port);
+ else if (speed == USB_SPEED_FULL)
+ value |= UTMI_FS(port);
+ else if (speed == USB_SPEED_LOW)
+ value |= UTMI_LS(port);
+ else
+ value |= UTMI_RST(port);
+ padctl_pmc_writel(priv, value, PMC_UTMIP_UHSIC_SAVED_STATE(port));
+
+ /* enable the trigger of the sleepwalk logic */
+ value = padctl_pmc_readl(priv, PMC_UTMIP_UHSIC_SLEEPWALK_CFG(port));
+ value |= UTMIP_LINEVAL_WALK_EN(port);
+ padctl_pmc_writel(priv, value, PMC_UTMIP_UHSIC_SLEEPWALK_CFG(port));
+
+ /* reset the walk pointer and clear the alarm of the sleepwalk logic,
+ * as well as capture the configuration of the USB2.0 pad
+ */
+ value = padctl_pmc_readl(priv, PMC_UTMIP_UHSIC_TRIGGERS);
+ value |= (UTMIP_CLR_WALK_PTR(port) | UTMIP_CLR_WAKE_ALARM(port) |
+ UTMIP_CAP_CFG(port));
+ padctl_pmc_writel(priv, value, PMC_UTMIP_UHSIC_TRIGGERS);
+
+ /* program electrical parameters read from XUSB PADCTL */
+ value = padctl_pmc_readl(priv, PMC_UTMIP_TERM_PAD_CFG);
+ value &= ~(TCTRL_VAL(~0) | PCTRL_VAL(~0));
+ value |= (TCTRL_VAL(tctrl) | PCTRL_VAL(pctrl));
+ padctl_pmc_writel(priv, value, PMC_UTMIP_TERM_PAD_CFG);
+
+ value = padctl_pmc_readl(priv, PMC_UTMIP_PAD_CFGX(port));
+ value &= ~RPD_CTRL_PX(~0);
+ value |= RPD_CTRL_PX(rpd_ctrl);
+ padctl_pmc_writel(priv, value, PMC_UTMIP_PAD_CFGX(port));
+
+ /* setup the pull-ups and pull-downs of the signals during the four
+ * stages of sleepwalk.
+ * if device is connected, program sleepwalk logic to maintain a J and
+ * keep driving K upon seeing remote wake.
+ */
+ value = padctl_pmc_readl(priv, PMC_UTMIP_SLEEPWALK_PX(port));
+ value = (UTMIP_USBOP_RPD_A | UTMIP_USBOP_RPD_B | UTMIP_USBOP_RPD_C |
+ UTMIP_USBOP_RPD_D);
+ value |= (UTMIP_USBON_RPD_A | UTMIP_USBON_RPD_B | UTMIP_USBON_RPD_C |
+ UTMIP_USBON_RPD_D);
+ if (speed == USB_SPEED_UNKNOWN) {
+ value |= (UTMIP_HIGHZ_A | UTMIP_HIGHZ_B | UTMIP_HIGHZ_C |
+ UTMIP_HIGHZ_D);
+ } else if ((speed == USB_SPEED_HIGH) || (speed == USB_SPEED_FULL)) {
+ /* J state: D+/D- = high/low, K state: D+/D- = low/high */
+ value |= UTMIP_HIGHZ_A;
+ value |= UTMIP_AP_A;
+ value |= (UTMIP_AN_B | UTMIP_AN_C | UTMIP_AN_D);
+ } else if (speed == USB_SPEED_LOW) {
+ /* J state: D+/D- = low/high, K state: D+/D- = high/low */
+ value |= UTMIP_HIGHZ_A;
+ value |= UTMIP_AN_A;
+ value |= (UTMIP_AP_B | UTMIP_AP_C | UTMIP_AP_D);
+ }
+ padctl_pmc_writel(priv, value, PMC_UTMIP_SLEEPWALK_PX(port));
+
+ /* power up the line state detectors of the pad */
+ value = padctl_pmc_readl(priv, PMC_USB_AO);
+ value &= ~(USBOP_VAL_PD(port) | USBON_VAL_PD(port));
+ padctl_pmc_writel(priv, value, PMC_USB_AO);
+
+ usleep_range(50, 100);
+
+ /* switch the electric control of the USB2.0 pad to PMC */
+ value = padctl_pmc_readl(priv, PMC_UTMIP_UHSIC_SLEEP_CFG(port));
+ value |= (UTMIP_FSLS_USE_PMC(port) | UTMIP_PCTRL_USE_PMC(port) |
+ UTMIP_TCTRL_USE_PMC(port));
+ padctl_pmc_writel(priv, value, PMC_UTMIP_UHSIC_SLEEP_CFG(port));
+
+ value = padctl_pmc_readl(priv, PMC_UTMIP_UHSIC_SLEEP_CFG1);
+ value |= (UTMIP_RPD_CTRL_USE_PMC_PX(port) |
+ UTMIP_RPU_SWITC_LOW_USE_PMC_PX(port));
+ padctl_pmc_writel(priv, value, PMC_UTMIP_UHSIC_SLEEP_CFG1);
+
+ /* set the wake signaling trigger events */
+ value = padctl_pmc_readl(priv, PMC_UTMIP_UHSIC_SLEEP_CFG(port));
+ value &= ~UTMIP_WAKE_VAL(port, ~0);
+ value |= UTMIP_WAKE_VAL_ANY(port);
+ padctl_pmc_writel(priv, value, PMC_UTMIP_UHSIC_SLEEP_CFG(port));
+
+ /* enable the wake detection */
+ value = padctl_pmc_readl(priv, PMC_UTMIP_UHSIC_SLEEP_CFG(port));
+ value |= UTMIP_MASTER_ENABLE(port);
+ padctl_pmc_writel(priv, value, PMC_UTMIP_UHSIC_SLEEP_CFG(port));
+
+ value = padctl_pmc_readl(priv, PMC_UTMIP_UHSIC_LINE_WAKEUP);
+ value |= UTMIP_LINE_WAKEUP_EN(port);
+ padctl_pmc_writel(priv, value, PMC_UTMIP_UHSIC_LINE_WAKEUP);
+
+ return 0;
+}
+
+static int tegra210_pmc_utmi_disable_phy_sleepwalk(struct tegra_xusb_lane *lane)
+{
+ struct tegra_xusb_padctl *padctl = lane->pad->padctl;
+ struct tegra210_xusb_padctl *priv = to_tegra210_xusb_padctl(padctl);
+ struct device *dev = padctl->dev;
+ unsigned int port = lane->index;
+ u32 value;
+
+ if (!priv->regmap)
+ return -EOPNOTSUPP;
+
+ dev_dbg(dev, "phy disable sleepwalk usb2 %d\n", port);
+
+ /* disable the wake detection */
+ value = padctl_pmc_readl(priv, PMC_UTMIP_UHSIC_SLEEP_CFG(port));
+ value &= ~UTMIP_MASTER_ENABLE(port);
+ padctl_pmc_writel(priv, value, PMC_UTMIP_UHSIC_SLEEP_CFG(port));
+
+ value = padctl_pmc_readl(priv, PMC_UTMIP_UHSIC_LINE_WAKEUP);
+ value &= ~UTMIP_LINE_WAKEUP_EN(port);
+ padctl_pmc_writel(priv, value, PMC_UTMIP_UHSIC_LINE_WAKEUP);
+
+ /* switch the electric control of the USB2.0 pad to XUSB or USB2 */
+ value = padctl_pmc_readl(priv, PMC_UTMIP_UHSIC_SLEEP_CFG(port));
+ value &= ~(UTMIP_FSLS_USE_PMC(port) | UTMIP_PCTRL_USE_PMC(port) |
+ UTMIP_TCTRL_USE_PMC(port));
+ padctl_pmc_writel(priv, value, PMC_UTMIP_UHSIC_SLEEP_CFG(port));
+
+ value = padctl_pmc_readl(priv, PMC_UTMIP_UHSIC_SLEEP_CFG1);
+ value &= ~(UTMIP_RPD_CTRL_USE_PMC_PX(port) |
+ UTMIP_RPU_SWITC_LOW_USE_PMC_PX(port));
+ padctl_pmc_writel(priv, value, PMC_UTMIP_UHSIC_SLEEP_CFG1);
+
+ /* disable wake event triggers of sleepwalk logic */
+ value = padctl_pmc_readl(priv, PMC_UTMIP_UHSIC_SLEEP_CFG(port));
+ value &= ~UTMIP_WAKE_VAL(port, ~0);
+ value |= UTMIP_WAKE_VAL_NONE(port);
+ padctl_pmc_writel(priv, value, PMC_UTMIP_UHSIC_SLEEP_CFG(port));
+
+ /* power down the line state detectors of the port */
+ value = padctl_pmc_readl(priv, PMC_USB_AO);
+ value |= (USBOP_VAL_PD(port) | USBON_VAL_PD(port));
+ padctl_pmc_writel(priv, value, PMC_USB_AO);
+
+ /* clear alarm of the sleepwalk logic */
+ value = padctl_pmc_readl(priv, PMC_UTMIP_UHSIC_TRIGGERS);
+ value |= UTMIP_CLR_WAKE_ALARM(port);
+ padctl_pmc_writel(priv, value, PMC_UTMIP_UHSIC_TRIGGERS);
+
+ return 0;
+}
+
+static int tegra210_pmc_hsic_enable_phy_sleepwalk(struct tegra_xusb_lane *lane,
+ enum usb_device_speed speed)
+{
+ struct tegra_xusb_padctl *padctl = lane->pad->padctl;
+ struct tegra210_xusb_padctl *priv = to_tegra210_xusb_padctl(padctl);
+ struct device *dev = padctl->dev;
+ unsigned int port = lane->index;
+ u32 value;
+
+ if (!priv->regmap)
+ return -EOPNOTSUPP;
+
+ dev_dbg(dev, "phy enable sleepwalk hsic %d\n", port);
+
+ /* ensure sleepwalk logic is disabled */
+ value = padctl_pmc_readl(priv, PMC_UHSIC_SLEEP_CFG);
+ value &= ~UHSIC_MASTER_ENABLE;
+ padctl_pmc_writel(priv, value, PMC_UHSIC_SLEEP_CFG);
+
+ /* ensure sleepwalk logics are in low power mode */
+ value = padctl_pmc_readl(priv, PMC_UTMIP_MASTER_CONFIG);
+ value |= UHSIC_PWR(port);
+ padctl_pmc_writel(priv, value, PMC_UTMIP_MASTER_CONFIG);
+
+ /* set debounce time */
+ value = padctl_pmc_readl(priv, PMC_USB_DEBOUNCE_DEL);
+ value &= ~UHSIC_LINE_DEB_CNT(~0);
+ value |= UHSIC_LINE_DEB_CNT(0x1);
+ padctl_pmc_writel(priv, value, PMC_USB_DEBOUNCE_DEL);
+
+ /* ensure fake events of sleepwalk logic are desiabled */
+ value = padctl_pmc_readl(priv, PMC_UHSIC_FAKE);
+ value &= ~(UHSIC_FAKE_STROBE_VAL | UHSIC_FAKE_DATA_VAL |
+ UHSIC_FAKE_STROBE_EN | UHSIC_FAKE_DATA_EN);
+ padctl_pmc_writel(priv, value, PMC_UHSIC_FAKE);
+
+ /* ensure wake events of sleepwalk logic are not latched */
+ value = padctl_pmc_readl(priv, PMC_UTMIP_UHSIC_LINE_WAKEUP);
+ value &= ~UHSIC_LINE_WAKEUP_EN;
+ padctl_pmc_writel(priv, value, PMC_UTMIP_UHSIC_LINE_WAKEUP);
+
+ /* disable wake event triggers of sleepwalk logic */
+ value = padctl_pmc_readl(priv, PMC_UHSIC_SLEEP_CFG);
+ value &= ~UHSIC_WAKE_VAL(~0);
+ value |= UHSIC_WAKE_VAL_NONE;
+ padctl_pmc_writel(priv, value, PMC_UHSIC_SLEEP_CFG);
+
+ /* power down the line state detectors of the port */
+ value = padctl_pmc_readl(priv, PMC_USB_AO);
+ value |= (STROBE_VAL_PD(port) | DATA0_VAL_PD(port) | DATA1_VAL_PD);
+ padctl_pmc_writel(priv, value, PMC_USB_AO);
+
+ /* save state, HSIC always comes up as HS */
+ value = padctl_pmc_readl(priv, PMC_UHSIC_SAVED_STATE);
+ value &= ~UHSIC_MODE(~0);
+ value |= UHSIC_HS;
+ padctl_pmc_writel(priv, value, PMC_UHSIC_SAVED_STATE);
+
+ /* enable the trigger of the sleepwalk logic */
+ value = padctl_pmc_readl(priv, PMC_UHSIC_SLEEPWALK_CFG);
+ value |= (UHSIC_WAKE_WALK_EN | UHSIC_LINEVAL_WALK_EN);
+ padctl_pmc_writel(priv, value, PMC_UHSIC_SLEEPWALK_CFG);
+
+ /* reset the walk pointer and clear the alarm of the sleepwalk logic,
+ * as well as capture the configuration of the USB2.0 port
+ */
+ value = padctl_pmc_readl(priv, PMC_UTMIP_UHSIC_TRIGGERS);
+ value |= (UHSIC_CLR_WALK_PTR | UHSIC_CLR_WAKE_ALARM);
+ padctl_pmc_writel(priv, value, PMC_UTMIP_UHSIC_TRIGGERS);
+
+ /* setup the pull-ups and pull-downs of the signals during the four
+ * stages of sleepwalk.
+ * maintain a HSIC IDLE and keep driving HSIC RESUME upon remote wake
+ */
+ value = padctl_pmc_readl(priv, PMC_UHSIC_SLEEPWALK_P0);
+ value = (UHSIC_DATA0_RPD_A | UHSIC_DATA0_RPU_B | UHSIC_DATA0_RPU_C |
+ UHSIC_DATA0_RPU_D);
+ value |= (UHSIC_STROBE_RPU_A | UHSIC_STROBE_RPD_B | UHSIC_STROBE_RPD_C |
+ UHSIC_STROBE_RPD_D);
+ padctl_pmc_writel(priv, value, PMC_UHSIC_SLEEPWALK_P0);
+
+ /* power up the line state detectors of the port */
+ value = padctl_pmc_readl(priv, PMC_USB_AO);
+ value &= ~(STROBE_VAL_PD(port) | DATA0_VAL_PD(port) | DATA1_VAL_PD);
+ padctl_pmc_writel(priv, value, PMC_USB_AO);
+
+ usleep_range(50, 100);
+
+ /* set the wake signaling trigger events */
+ value = padctl_pmc_readl(priv, PMC_UHSIC_SLEEP_CFG);
+ value &= ~UHSIC_WAKE_VAL(~0);
+ value |= UHSIC_WAKE_VAL_SD10;
+ padctl_pmc_writel(priv, value, PMC_UHSIC_SLEEP_CFG);
+
+ /* enable the wake detection */
+ value = padctl_pmc_readl(priv, PMC_UHSIC_SLEEP_CFG);
+ value |= UHSIC_MASTER_ENABLE;
+ padctl_pmc_writel(priv, value, PMC_UHSIC_SLEEP_CFG);
+
+ value = padctl_pmc_readl(priv, PMC_UTMIP_UHSIC_LINE_WAKEUP);
+ value |= UHSIC_LINE_WAKEUP_EN;
+ padctl_pmc_writel(priv, value, PMC_UTMIP_UHSIC_LINE_WAKEUP);
+
+ return 0;
+}
+
+static int tegra210_pmc_hsic_disable_phy_sleepwalk(struct tegra_xusb_lane *lane)
+{
+ struct tegra_xusb_padctl *padctl = lane->pad->padctl;
+ struct tegra210_xusb_padctl *priv = to_tegra210_xusb_padctl(padctl);
+ struct device *dev = padctl->dev;
+ unsigned int port = lane->index;
+ u32 value;
+
+ if (!priv->regmap)
+ return -EOPNOTSUPP;
+
+ dev_dbg(dev, "phy disable sleepwalk hsic %d\n", port);
+
+ /* disable the wake detection */
+ value = padctl_pmc_readl(priv, PMC_UHSIC_SLEEP_CFG);
+ value &= ~UHSIC_MASTER_ENABLE;
+ padctl_pmc_writel(priv, value, PMC_UHSIC_SLEEP_CFG);
+
+ value = padctl_pmc_readl(priv, PMC_UTMIP_UHSIC_LINE_WAKEUP);
+ value &= ~UHSIC_LINE_WAKEUP_EN;
+ padctl_pmc_writel(priv, value, PMC_UTMIP_UHSIC_LINE_WAKEUP);
+
+ /* disable wake event triggers of sleepwalk logic */
+ value = padctl_pmc_readl(priv, PMC_UHSIC_SLEEP_CFG);
+ value &= ~UHSIC_WAKE_VAL(~0);
+ value |= UHSIC_WAKE_VAL_NONE;
+ padctl_pmc_writel(priv, value, PMC_UHSIC_SLEEP_CFG);
+
+ /* power down the line state detectors of the port */
+ value = padctl_pmc_readl(priv, PMC_USB_AO);
+ value |= (STROBE_VAL_PD(port) | DATA0_VAL_PD(port) | DATA1_VAL_PD);
+ padctl_pmc_writel(priv, value, PMC_USB_AO);
+
+ /* clear alarm of the sleepwalk logic */
+ value = padctl_pmc_readl(priv, PMC_UTMIP_UHSIC_TRIGGERS);
+ value |= UHSIC_CLR_WAKE_ALARM;
+ padctl_pmc_writel(priv, value, PMC_UTMIP_UHSIC_TRIGGERS);
+
+ return 0;
+}
+
static int tegra210_usb3_set_lfps_detect(struct tegra_xusb_padctl *padctl,
unsigned int index, bool enable)
{
@@ -986,6 +1808,11 @@ static void tegra210_usb2_lane_remove(struct tegra_xusb_lane *lane)
static const struct tegra_xusb_lane_ops tegra210_usb2_lane_ops = {
.probe = tegra210_usb2_lane_probe,
.remove = tegra210_usb2_lane_remove,
+ .enable_phy_sleepwalk = tegra210_pmc_utmi_enable_phy_sleepwalk,
+ .disable_phy_sleepwalk = tegra210_pmc_utmi_disable_phy_sleepwalk,
+ .enable_phy_wake = tegra210_utmi_enable_phy_wake,
+ .disable_phy_wake = tegra210_utmi_disable_phy_wake,
+ .remote_wake_detected = tegra210_utmi_phy_remote_wake_detected,
};
static int tegra210_usb2_phy_init(struct phy *phy)
@@ -1449,6 +2276,11 @@ static void tegra210_hsic_lane_remove(struct tegra_xusb_lane *lane)
static const struct tegra_xusb_lane_ops tegra210_hsic_lane_ops = {
.probe = tegra210_hsic_lane_probe,
.remove = tegra210_hsic_lane_remove,
+ .enable_phy_sleepwalk = tegra210_pmc_hsic_enable_phy_sleepwalk,
+ .disable_phy_sleepwalk = tegra210_pmc_hsic_disable_phy_sleepwalk,
+ .enable_phy_wake = tegra210_hsic_enable_phy_wake,
+ .disable_phy_wake = tegra210_hsic_disable_phy_wake,
+ .remote_wake_detected = tegra210_hsic_phy_remote_wake_detected,
};
static int tegra210_hsic_phy_init(struct phy *phy)
@@ -1879,6 +2711,11 @@ static const struct tegra_xusb_lane_ops tegra210_pcie_lane_ops = {
.remove = tegra210_pcie_lane_remove,
.iddq_enable = tegra210_uphy_lane_iddq_enable,
.iddq_disable = tegra210_uphy_lane_iddq_disable,
+ .enable_phy_sleepwalk = tegra210_usb3_enable_phy_sleepwalk,
+ .disable_phy_sleepwalk = tegra210_usb3_disable_phy_sleepwalk,
+ .enable_phy_wake = tegra210_usb3_enable_phy_wake,
+ .disable_phy_wake = tegra210_usb3_disable_phy_wake,
+ .remote_wake_detected = tegra210_usb3_phy_remote_wake_detected,
};
static int tegra210_pcie_phy_init(struct phy *phy)
@@ -2044,6 +2881,11 @@ static const struct tegra_xusb_lane_ops tegra210_sata_lane_ops = {
.remove = tegra210_sata_lane_remove,
.iddq_enable = tegra210_uphy_lane_iddq_enable,
.iddq_disable = tegra210_uphy_lane_iddq_disable,
+ .enable_phy_sleepwalk = tegra210_usb3_enable_phy_sleepwalk,
+ .disable_phy_sleepwalk = tegra210_usb3_disable_phy_sleepwalk,
+ .enable_phy_wake = tegra210_usb3_enable_phy_wake,
+ .disable_phy_wake = tegra210_usb3_disable_phy_wake,
+ .remote_wake_detected = tegra210_usb3_phy_remote_wake_detected,
};
static int tegra210_sata_phy_init(struct phy *phy)
@@ -2293,6 +3135,8 @@ tegra210_xusb_padctl_probe(struct device *dev,
const struct tegra_xusb_padctl_soc *soc)
{
struct tegra210_xusb_padctl *padctl;
+ struct device_node *np;
+ struct platform_device *pdev;
int err;
padctl = devm_kzalloc(dev, sizeof(*padctl), GFP_KERNEL);
@@ -2306,6 +3150,26 @@ tegra210_xusb_padctl_probe(struct device *dev,
if (err < 0)
return ERR_PTR(err);
+ np = of_parse_phandle(dev->of_node, "nvidia,pmc", 0);
+ if (!np) {
+ dev_warn(dev, "nvidia,pmc property is missing\n");
+ goto out;
+ }
+
+ pdev = of_find_device_by_node(np);
+ if (!pdev) {
+ dev_warn(dev, "PMC device is not available\n");
+ goto out;
+ }
+
+ if (!device_is_bound(&pdev->dev))
+ return ERR_PTR(-EPROBE_DEFER);
+
+ padctl->regmap = dev_get_regmap(&pdev->dev, "usb_sleepwalk");
+ if (!padctl->regmap)
+ dev_info(dev, "pmc regmap is not available.\n");
+
+out:
return &padctl->base;
}
@@ -2313,9 +3177,75 @@ static void tegra210_xusb_padctl_remove(struct tegra_xusb_padctl *padctl)
{
}
+static void tegra210_xusb_padctl_save(struct tegra_xusb_padctl *padctl)
+{
+ struct tegra210_xusb_padctl *priv = to_tegra210_xusb_padctl(padctl);
+
+ priv->context.usb2_pad_mux =
+ padctl_readl(padctl, XUSB_PADCTL_USB2_PAD_MUX);
+ priv->context.usb2_port_cap =
+ padctl_readl(padctl, XUSB_PADCTL_USB2_PORT_CAP);
+ priv->context.ss_port_map =
+ padctl_readl(padctl, XUSB_PADCTL_SS_PORT_MAP);
+ priv->context.usb3_pad_mux =
+ padctl_readl(padctl, XUSB_PADCTL_USB3_PAD_MUX);
+}
+
+static void tegra210_xusb_padctl_restore(struct tegra_xusb_padctl *padctl)
+{
+ struct tegra210_xusb_padctl *priv = to_tegra210_xusb_padctl(padctl);
+ struct tegra_xusb_lane *lane;
+
+ padctl_writel(padctl, priv->context.usb2_pad_mux,
+ XUSB_PADCTL_USB2_PAD_MUX);
+ padctl_writel(padctl, priv->context.usb2_port_cap,
+ XUSB_PADCTL_USB2_PORT_CAP);
+ padctl_writel(padctl, priv->context.ss_port_map,
+ XUSB_PADCTL_SS_PORT_MAP);
+
+ list_for_each_entry(lane, &padctl->lanes, list) {
+ if (lane->pad->ops->iddq_enable)
+ tegra210_uphy_lane_iddq_enable(lane);
+ }
+
+ padctl_writel(padctl, priv->context.usb3_pad_mux,
+ XUSB_PADCTL_USB3_PAD_MUX);
+
+ list_for_each_entry(lane, &padctl->lanes, list) {
+ if (lane->pad->ops->iddq_disable)
+ tegra210_uphy_lane_iddq_disable(lane);
+ }
+}
+
+static int tegra210_xusb_padctl_suspend_noirq(struct tegra_xusb_padctl *padctl)
+{
+ mutex_lock(&padctl->lock);
+
+ tegra210_uphy_deinit(padctl);
+
+ tegra210_xusb_padctl_save(padctl);
+
+ mutex_unlock(&padctl->lock);
+ return 0;
+}
+
+static int tegra210_xusb_padctl_resume_noirq(struct tegra_xusb_padctl *padctl)
+{
+ mutex_lock(&padctl->lock);
+
+ tegra210_xusb_padctl_restore(padctl);
+
+ tegra210_uphy_init(padctl);
+
+ mutex_unlock(&padctl->lock);
+ return 0;
+}
+
static const struct tegra_xusb_padctl_ops tegra210_xusb_padctl_ops = {
.probe = tegra210_xusb_padctl_probe,
.remove = tegra210_xusb_padctl_remove,
+ .suspend_noirq = tegra210_xusb_padctl_suspend_noirq,
+ .resume_noirq = tegra210_xusb_padctl_resume_noirq,
.usb3_set_lfps_detect = tegra210_usb3_set_lfps_detect,
.hsic_set_idle = tegra210_hsic_set_idle,
.vbus_override = tegra210_xusb_padctl_vbus_override,
--
2.25.1
