This adds DT bindings for the Microsemi/Microchip SGPIO controller, bindings microchip,sparx5-sgpio, mscc,ocelot-sgpio and mscc,luton-sgpio. Signed-off-by: Lars Povlsen <lars.povlsen@xxxxxxxxxxxxx> --- .../pinctrl/microchip,sparx5-sgpio.yaml | 140 ++++++++++++++++++ 1 file changed, 140 insertions(+) create mode 100644 Documentation/devicetree/bindings/pinctrl/microchip,sparx5-sgpio.yaml diff --git a/Documentation/devicetree/bindings/pinctrl/microchip,sparx5-sgpio.yaml b/Documentation/devicetree/bindings/pinctrl/microchip,sparx5-sgpio.yaml new file mode 100644 index 000000000000..fc41495800ed --- /dev/null +++ b/Documentation/devicetree/bindings/pinctrl/microchip,sparx5-sgpio.yaml @@ -0,0 +1,140 @@ +# SPDX-License-Identifier: GPL-2.0-only OR BSD-2-Clause +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/pinctrl/microchip,sparx5-sgpio.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Microsemi/Microchip Serial GPIO controller + +maintainers: + - Lars Povlsen <lars.povlsen@xxxxxxxxxxxxx> + +description: | + By using a serial interface, the SIO controller significantly extend + the number of available GPIOs with a minimum number of additional + pins on the device. The primary purpose of the SIO controllers is to + connect control signals from SFP modules and to act as an LED + controller. + +properties: + $nodename: + pattern: "^gpio@[0-9a-f]+$" + + compatible: + enum: + - microchip,sparx5-sgpio + - mscc,ocelot-sgpio + - mscc,luton-sgpio + + "#address-cells": + const: 1 + + "#size-cells": + const: 0 + + reg: + maxItems: 1 + + clocks: + maxItems: 1 + + microchip,sgpio-port-ranges: + description: This is a sequence of tuples, defining intervals of + enabled ports in the serial input stream. The enabled ports must + match the hardware configuration in order for signals to be + properly written/read to/from the controller holding + registers. Being tuples, then number of arguments must be + even. The tuples mast be ordered (low, high) and are + inclusive. + $ref: /schemas/types.yaml#/definitions/uint32-matrix + items: + items: + - description: | + "low" indicates start bit number of range + minimum: 0 + maximum: 31 + - description: | + "high" indicates end bit number of range + minimum: 0 + maximum: 31 + minItems: 1 + maxItems: 32 + + microchip,sgpio-frequency: + description: The sgpio controller frequency (Hz). This dictates + the serial bitstream speed, which again affects the latency in + getting control signals back and forth between external shift + registers. The speed must be no larger than half the system + clock, and larger than zero. + $ref: /schemas/types.yaml#/definitions/uint32 + minimum: 1 + default: 12500000 + +patternProperties: + "^gpio@[0-1]$": + type: object + properties: + compatible: + const: microchip,sparx5-sgpio-bank + + reg: + description: | + The GPIO bank number. "0" is designates the input pin bank, + "1" the output bank. + maxItems: 1 + + gpio-controller: true + + '#gpio-cells': + const: 3 + + ngpios: + minimum: 1 + maximum: 128 + + required: + - compatible + - reg + - gpio-controller + - '#gpio-cells' + - ngpios + + additionalProperties: false + +additionalProperties: false + +required: + - compatible + - reg + - clocks + - microchip,sgpio-port-ranges + - "#address-cells" + - "#size-cells" + +examples: + - | + sgpio2: gpio@1101059c { + #address-cells = <1>; + #size-cells = <0>; + compatible = "microchip,sparx5-sgpio"; + clocks = <&sys_clk>; + pinctrl-0 = <&sgpio2_pins>; + pinctrl-names = "default"; + reg = <0x1101059c 0x100>; + microchip,sgpio-port-ranges = <0 0>, <16 18>, <28 31>; + microchip,sgpio-frequency = <25000000>; + sgpio_in2: gpio@0 { + reg = <0>; + compatible = "microchip,sparx5-sgpio-bank"; + gpio-controller; + #gpio-cells = <3>; + ngpios = <96>; + }; + sgpio_out2: gpio@1 { + compatible = "microchip,sparx5-sgpio-bank"; + reg = <1>; + gpio-controller; + #gpio-cells = <3>; + ngpios = <96>; + }; + }; -- 2.25.1
