Define the network interface names for the switch ports and hook them up
to the 2 QSGMII PHYs that are onboard.
A conscious decision was taken to go along with the numbers that are
written on the front panel of the board and not with the hardware
numbers of the switch chip ports. The 2 numbering schemes are
shifted by 8.
Signed-off-by: Vladimir Oltean <vladimir.oltean@xxxxxxx>
Reviewed-by: Maxim Kochetkov <fido_max@xxxxxxxx>
---
Changes in v3:
Renamed interfaces from swpN to ETHN, as per Andrew Lunn's suggestion.
Changes in v2:
Use the existing way of accessing the mdio bus and not labels.
arch/powerpc/boot/dts/fsl/t1040rdb.dts | 107 +++++++++++++++++++++++++
1 file changed, 107 insertions(+)
diff --git a/arch/powerpc/boot/dts/fsl/t1040rdb.dts b/arch/powerpc/boot/dts/fsl/t1040rdb.dts
index 65ff34c49025..e4067f3d2980 100644
--- a/arch/powerpc/boot/dts/fsl/t1040rdb.dts
+++ b/arch/powerpc/boot/dts/fsl/t1040rdb.dts
@@ -64,6 +64,40 @@ mdio@fc000 {
phy_sgmii_2: ethernet-phy@3 {
reg = <0x03>;
};
+
+ /* VSC8514 QSGMII PHY */
+ phy_qsgmii_0: ethernet-phy@4 {
+ reg = <0x4>;
+ };
+
+ phy_qsgmii_1: ethernet-phy@5 {
+ reg = <0x5>;
+ };
+
+ phy_qsgmii_2: ethernet-phy@6 {
+ reg = <0x6>;
+ };
+
+ phy_qsgmii_3: ethernet-phy@7 {
+ reg = <0x7>;
+ };
+
+ /* VSC8514 QSGMII PHY */
+ phy_qsgmii_4: ethernet-phy@8 {
+ reg = <0x8>;
+ };
+
+ phy_qsgmii_5: ethernet-phy@9 {
+ reg = <0x9>;
+ };
+
+ phy_qsgmii_6: ethernet-phy@a {
+ reg = <0xa>;
+ };
+
+ phy_qsgmii_7: ethernet-phy@b {
+ reg = <0xb>;
+ };
};
};
};
@@ -76,3 +110,76 @@ cpld@3,0 {
};
#include "t1040si-post.dtsi"
+
+&seville_switch {
+ status = "okay";
+};
+
+&seville_port0 {
+ managed = "in-band-status";
+ phy-handle = <&phy_qsgmii_0>;
+ phy-mode = "qsgmii";
+ label = "ETH4";
+ status = "okay";
+};
+
+&seville_port1 {
+ managed = "in-band-status";
+ phy-handle = <&phy_qsgmii_1>;
+ phy-mode = "qsgmii";
+ label = "ETH5";
+ status = "okay";
+};
+
+&seville_port2 {
+ managed = "in-band-status";
+ phy-handle = <&phy_qsgmii_2>;
+ phy-mode = "qsgmii";
+ label = "ETH6";
+ status = "okay";
+};
+
+&seville_port3 {
+ managed = "in-band-status";
+ phy-handle = <&phy_qsgmii_3>;
+ phy-mode = "qsgmii";
+ label = "ETH7";
+ status = "okay";
+};
+
+&seville_port4 {
+ managed = "in-band-status";
+ phy-handle = <&phy_qsgmii_4>;
+ phy-mode = "qsgmii";
+ label = "ETH8";
+ status = "okay";
+};
+
+&seville_port5 {
+ managed = "in-band-status";
+ phy-handle = <&phy_qsgmii_5>;
+ phy-mode = "qsgmii";
+ label = "ETH9";
+ status = "okay";
+};
+
+&seville_port6 {
+ managed = "in-band-status";
+ phy-handle = <&phy_qsgmii_6>;
+ phy-mode = "qsgmii";
+ label = "ETH10";
+ status = "okay";
+};
+
+&seville_port7 {
+ managed = "in-band-status";
+ phy-handle = <&phy_qsgmii_7>;
+ phy-mode = "qsgmii";
+ label = "ETH11";
+ status = "okay";
+};
+
+&seville_port8 {
+ ethernet = <&enet0>;
+ status = "okay";
+};
--
2.25.1
