Re: [PATCH v6 3/3] media: i2c: imx274: Add IMX274 power on and off sequence

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 




On 9/22/20 12:55 AM, Thierry Reding wrote:
On Mon, Sep 21, 2020 at 02:39:39PM -0700, Sowjanya Komatineni wrote:
IMX274 has analog 2.8V supply, digital core 1.8V supply, and vddl digital
io 1.2V supply which are optional based on camera module design.

IMX274 also need external 24Mhz clock and is optional based on
camera module design.

This patch adds support for IMX274 power on and off to enable and
disable these supplies and external clock.

Reviewed-by: Luca Ceresoli <luca@xxxxxxxxxxxxxxxx>
Signed-off-by: Sowjanya Komatineni <skomatineni@xxxxxxxxxx>
---
  drivers/media/i2c/imx274.c | 184 +++++++++++++++++++++++++++++++++------------
  1 file changed, 134 insertions(+), 50 deletions(-)

diff --git a/drivers/media/i2c/imx274.c b/drivers/media/i2c/imx274.c
index 5e515f0..b3057a5 100644
--- a/drivers/media/i2c/imx274.c
+++ b/drivers/media/i2c/imx274.c
@@ -18,7 +18,9 @@
  #include <linux/kernel.h>
  #include <linux/module.h>
  #include <linux/of_gpio.h>
+#include <linux/pm_runtime.h>
  #include <linux/regmap.h>
+#include <linux/regulator/consumer.h>
  #include <linux/slab.h>
  #include <linux/v4l2-mediabus.h>
  #include <linux/videodev2.h>
@@ -131,6 +133,15 @@
  #define IMX274_TABLE_WAIT_MS			0
  #define IMX274_TABLE_END			1
+/* regulator supplies */
+static const char * const imx274_supply_names[] = {
+	"vddl",  /* IF (1.2V) supply */
+	"vdig",  /* Digital Core (1.8V) supply */
+	"vana",  /* Analog (2.8V) supply */
According to the device tree bindings these should be uppercase. Did I
miss a patch that updates the bindings?

I think the preference is for supply names to be lowercase and given
that there are no users of this binding yet we could update it without
breaking any existing device trees.

+};
+
+#define IMX274_NUM_SUPPLIES ARRAY_SIZE(imx274_supply_names)
+
  /*
   * imx274 I2C operation related structure
   */
@@ -501,6 +512,8 @@ struct imx274_ctrls {
   * @frame_rate: V4L2 frame rate structure
   * @regmap: Pointer to regmap structure
   * @reset_gpio: Pointer to reset gpio
+ * @supplies: List of analog and digital supply regulators
+ * @inck: Pointer to sensor input clock
   * @lock: Mutex structure
   * @mode: Parameters for the selected readout mode
   */
@@ -514,6 +527,8 @@ struct stimx274 {
  	struct v4l2_fract frame_interval;
  	struct regmap *regmap;
  	struct gpio_desc *reset_gpio;
+	struct regulator_bulk_data supplies[IMX274_NUM_SUPPLIES];
+	struct clk *inck;
  	struct mutex lock; /* mutex lock for operations */
  	const struct imx274_mode *mode;
  };
@@ -726,6 +741,12 @@ static int imx274_start_stream(struct stimx274 *priv)
  {
  	int err = 0;
+ err = __v4l2_ctrl_handler_setup(&priv->ctrls.handler);
+	if (err) {
+		dev_err(&priv->client->dev, "Error %d setup controls\n", err);
+		return err;
+	}
+
  	/*
  	 * Refer to "Standby Cancel Sequence when using CSI-2" in
  	 * imx274 datasheet, it should wait 10ms or more here.
@@ -767,6 +788,66 @@ static void imx274_reset(struct stimx274 *priv, int rst)
  	usleep_range(IMX274_RESET_DELAY1, IMX274_RESET_DELAY2);
  }
+static int imx274_power_on(struct device *dev)
+{
+	struct i2c_client *client = to_i2c_client(dev);
+	struct v4l2_subdev *sd = i2c_get_clientdata(client);
+	struct stimx274 *imx274 = to_imx274(sd);
+	int ret;
+
+	/* keep sensor in reset before power on */
+	imx274_reset(imx274, 0);
+
+	ret = clk_prepare_enable(imx274->inck);
+	if (ret) {
+		dev_err(&imx274->client->dev,
+			"Failed to enable input clock: %d\n", ret);
+		return ret;
+	}
+
+	ret = regulator_bulk_enable(IMX274_NUM_SUPPLIES, imx274->supplies);
+	if (ret) {
+		dev_err(&imx274->client->dev,
+			"Failed to enable regulators: %d\n", ret);
+		goto fail_reg;
+	}
+
+	udelay(2);
This looks like some sort of extra delay to make sure all the supply
voltages have settled. Should this perhaps be encoded as part of the
regulator ramp-up times? Or is this really an IC-specific delay that
is needed for some internal timing?
This is IC-specific delay after power on regulators before releasing reset.

+	imx274_reset(imx274, 1);
+
+	return 0;
+
+fail_reg:
+	clk_disable_unprepare(imx274->inck);
+	return ret;
+}
+
+static int imx274_power_off(struct device *dev)
+{
+	struct i2c_client *client = to_i2c_client(dev);
+	struct v4l2_subdev *sd = i2c_get_clientdata(client);
+	struct stimx274 *imx274 = to_imx274(sd);
+
+	imx274_reset(imx274, 0);
+
+	regulator_bulk_disable(IMX274_NUM_SUPPLIES, imx274->supplies);
+
+	clk_disable_unprepare(imx274->inck);
+
+	return 0;
+}
+
+static int imx274_regulators_get(struct device *dev, struct stimx274 *imx274)
+{
+	unsigned int i;
+
+	for (i = 0; i < IMX274_NUM_SUPPLIES; i++)
+		imx274->supplies[i].supply = imx274_supply_names[i];
+
+	return devm_regulator_bulk_get(dev, IMX274_NUM_SUPPLIES,
+					imx274->supplies);
+}
+
  /**
   * imx274_s_ctrl - This is used to set the imx274 V4L2 controls
   * @ctrl: V4L2 control to be set
@@ -781,6 +862,9 @@ static int imx274_s_ctrl(struct v4l2_ctrl *ctrl)
  	struct stimx274 *imx274 = to_imx274(sd);
  	int ret = -EINVAL;
+ if (!pm_runtime_get_if_in_use(&imx274->client->dev))
+		return 0;
I'm not sure I understand this, and sorry if this has been discussed
earlier. Aren't there any other mechanisms in place to ensure that a
control can only be configured when in use? If so, then is this even
necessary?

If not, silently ignoring at this point seems like it could cause subtle
failures by ignoring some control settings and applying others if the
timing is right.

With this patch, v4l2_ctrl setup is moved to start stream so all the control values selected gets programmed during stream start. So s_ctrl callback execution happens during that time after sensor rpm resume and I don't think we need here either but I see all sensor drivers with RPM enabled checking for this. So added just to make sure sensor programming don't happen when power is off.

Sakari/Jacob,

Can you please clarify if we can remove check pm_runtime_get_if_in_use() in s_ctrl callback as v4l2_ctrl handler setup happens during stream start where power is already on by then?

+
  	dev_dbg(&imx274->client->dev,
  		"%s : s_ctrl: %s, value: %d\n", __func__,
  		ctrl->name, ctrl->val);
@@ -811,6 +895,8 @@ static int imx274_s_ctrl(struct v4l2_ctrl *ctrl)
  		break;
  	}
+ pm_runtime_put(&imx274->client->dev);
+
  	return ret;
  }
@@ -1269,10 +1355,8 @@ static int imx274_s_frame_interval(struct v4l2_subdev *sd,
   *
   * Return: 0 on success, errors otherwise
   */
-static int imx274_load_default(struct stimx274 *priv)
+static void imx274_load_default(struct stimx274 *priv)
  {
-	int ret;
-
  	/* load default control values */
  	priv->frame_interval.numerator = 1;
  	priv->frame_interval.denominator = IMX274_DEF_FRAME_RATE;
@@ -1280,29 +1364,6 @@ static int imx274_load_default(struct stimx274 *priv)
  	priv->ctrls.gain->val = IMX274_DEF_GAIN;
  	priv->ctrls.vflip->val = 0;
  	priv->ctrls.test_pattern->val = TEST_PATTERN_DISABLED;
-
-	/* update frame rate */
-	ret = imx274_set_frame_interval(priv,
-					priv->frame_interval);
-	if (ret)
-		return ret;
-
-	/* update exposure time */
-	ret = v4l2_ctrl_s_ctrl(priv->ctrls.exposure, priv->ctrls.exposure->val);
-	if (ret)
-		return ret;
-
-	/* update gain */
-	ret = v4l2_ctrl_s_ctrl(priv->ctrls.gain, priv->ctrls.gain->val);
-	if (ret)
-		return ret;
-
-	/* update vflip */
-	ret = v4l2_ctrl_s_ctrl(priv->ctrls.vflip, priv->ctrls.vflip->val);
-	if (ret)
-		return ret;
This is not moved to somewhere else, so I assume the equivalent will
happen somewhere higher up in the stack? Might be worth mentioning in
the commit message why this can be dropped.
OK. Will add in commit message.

Thierry



[Index of Archives]     [Device Tree Compilter]     [Device Tree Spec]     [Linux Driver Backports]     [Video for Linux]     [Linux USB Devel]     [Linux PCI Devel]     [Linux Audio Users]     [Linux Kernel]     [Linux SCSI]     [XFree86]     [Yosemite Backpacking]


  Powered by Linux