Hi Greg,
thanks for the review!
On Sun, Sep 20, 2020 at 04:17:20PM +0200, Greg Kroah-Hartman wrote:
> On Thu, Sep 17, 2020 at 11:46:22AM -0700, Matthias Kaehlcke wrote:
> > The main issue this driver addresses is that a USB hub needs to be
> > powered before it can be discovered. For onboard hubs this is often
> > solved by supplying the hub with an 'always-on' regulator, which is
> > kind of a hack. Some onboard hubs may require further initialization
> > steps, like changing the state of a GPIO or enabling a clock, which
> > requires further hacks. This driver creates a platform device
> > representing the hub which performs the necessary initialization.
> > Currently it only supports switching on a single regulator, support
> > for multiple regulators or other actions can be added as needed.
> > Different initialization sequences can be supported based on the
> > compatible string.
> >
> > Besides performing the initialization the driver can be configured
> > to power the hub off during system suspend. This can help to extend
> > battery life on battery powered devices which have no requirements
> > to keep the hub powered during suspend. The driver can also be
> > configured to leave the hub powered when a wakeup capable USB device
> > is connected when suspending, and power it off otherwise.
> >
> > Technically the driver consists of two drivers, the platform driver
> > described above and a very thin USB driver that subclasses the
> > generic driver. The purpose of this driver is to provide the platform
> > driver with the USB devices corresponding to the hub(s) (a hub
> > controller may provide multiple 'logical' hubs, e.g. one to support
> > USB 2.0 and another for USB 3.x).
> >
> > Co-developed-by: Ravi Chandra Sadineni <ravisadineni@xxxxxxxxxxxx>
> > Signed-off-by: Ravi Chandra Sadineni <ravisadineni@xxxxxxxxxxxx>
> > Signed-off-by: Matthias Kaehlcke <mka@xxxxxxxxxxxx>
> > ---
> >
> > Changes in v2:
> > - check wakeup enabled state of the USB controller instead of
> > using 'wakeup-source' property
> > - use sysfs attribute instead of DT property to determine if
> > the hub should be powered off at all during system suspend
> > - added missing brace in onboard_hub_suspend()
> > - updated commit message
> > - use pm_ptr for pm_ops as suggested by Alan
> >
> > Changes in v1:
> > - renamed the driver to 'onboard_usb_hub'
> > - single file for platform and USB driver
> > - USB hub devices register with the platform device
> > - the DT includes a phandle of the platform device
> > - the platform device now controls when power is turned off
> > - the USB driver became a very thin subclass of the generic USB
> > driver
> > - enabled autosuspend support
> >
> > drivers/usb/misc/Kconfig | 15 ++
> > drivers/usb/misc/Makefile | 1 +
> > drivers/usb/misc/onboard_usb_hub.c | 329 +++++++++++++++++++++++++++++
> > 3 files changed, 345 insertions(+)
> > create mode 100644 drivers/usb/misc/onboard_usb_hub.c
> >
> > diff --git a/drivers/usb/misc/Kconfig b/drivers/usb/misc/Kconfig
> > index 6818ea689cd9..e941244e24e5 100644
> > --- a/drivers/usb/misc/Kconfig
> > +++ b/drivers/usb/misc/Kconfig
> > @@ -275,3 +275,18 @@ config USB_CHAOSKEY
> >
> > To compile this driver as a module, choose M here: the
> > module will be called chaoskey.
> > +
> > +config USB_ONBOARD_HUB
> > + tristate "Onboard USB hub support"
> > + depends on OF
>
> What about COMPILE_TEST as well?
ok
> > + help
> > + Say Y here if you want to support onboard USB hubs. The driver
> > + powers supported hubs on and may perform other initialization
> > + steps.
> > +
> > + The driver can also switch off the power of the hub during
> > + system suspend if it is configured accordingly. This may
> > + reduce power consumption while the system is suspended.
> > +
> > + To compile this driver as a module, choose M here: the
> > + module will be called onboard_usb_hub.
> > diff --git a/drivers/usb/misc/Makefile b/drivers/usb/misc/Makefile
> > index da39bddb0604..6f10a1c6f7e9 100644
> > --- a/drivers/usb/misc/Makefile
> > +++ b/drivers/usb/misc/Makefile
> > @@ -31,3 +31,4 @@ obj-$(CONFIG_USB_CHAOSKEY) += chaoskey.o
> >
> > obj-$(CONFIG_USB_SISUSBVGA) += sisusbvga/
> > obj-$(CONFIG_USB_LINK_LAYER_TEST) += lvstest.o
> > +obj-$(CONFIG_USB_ONBOARD_HUB) += onboard_usb_hub.o
> > diff --git a/drivers/usb/misc/onboard_usb_hub.c b/drivers/usb/misc/onboard_usb_hub.c
> > new file mode 100644
> > index 000000000000..206798029041
> > --- /dev/null
> > +++ b/drivers/usb/misc/onboard_usb_hub.c
> > @@ -0,0 +1,329 @@
> > +// SPDX-License-Identifier: GPL-2.0-only
> > +/*
> > + * Driver for onboard USB hubs
> > + *
> > + * Copyright (c) 2020, Google LLC
> > + */
> > +
> > +#include <linux/init.h>
> > +#include <linux/kernel.h>
> > +#include <linux/module.h>
> > +#include <linux/mutex.h>
> > +#include <linux/of.h>
> > +#include <linux/of_platform.h>
> > +#include <linux/platform_device.h>
> > +#include <linux/regulator/consumer.h>
> > +#include <linux/suspend.h>
> > +#include <linux/usb.h>
> > +#include <linux/usb/hcd.h>
> > +#include "../core/usb.h"
>
> Why do you need private usb core functions?
An earlier version of the driver used usb_port_disable(), but that isn't needed
anymore, I'll remove the include.
> > +
> > +/************************** Platform driver **************************/
> > +
> > +struct udev_node {
> > + struct usb_device *udev;
> > + struct list_head list;
> > +};
> > +
> > +struct onboard_hub {
> > + struct regulator *vdd;
> > + struct device *dev;
> > + bool power_off_in_suspend;
> > + struct list_head udev_list;
> > + struct mutex lock;
> > + bool has_wakeup_capable_descendants;
> > +};
> > +
> > +static int onboard_hub_power_on(struct onboard_hub *hub)
> > +{
> > + int err;
> > +
> > + err = regulator_enable(hub->vdd);
> > + if (err) {
> > + dev_err(hub->dev, "failed to enable regulator: %d\n", err);
> > + return err;
> > + }
>
> Nit, no need for { } or return err here, just return err one line below.
ack
> > +
> > + return 0;
> > +}
> > +
> > +static int onboard_hub_power_off(struct onboard_hub *hub)
> > +{
> > + int err;
> > +
> > + err = regulator_disable(hub->vdd);
> > + if (err) {
> > + dev_err(hub->dev, "failed to enable regulator: %d\n", err);
> > + return err;
> > + }
> > +
> > + return 0;
>
> Same here.
ack
> > +}
> > +
> > +static int __maybe_unused onboard_hub_suspend(struct device *dev)
> > +{
> > + struct onboard_hub *hub = dev_get_drvdata(dev);
> > + struct udev_node *node;
> > + int rc = 0;
> > +
> > + hub->has_wakeup_capable_descendants = false;
> > +
> > + if (!hub->power_off_in_suspend)
> > + return 0;
> > +
> > + mutex_lock(&hub->lock);
> > +
> > + list_for_each_entry(node, &hub->udev_list, list) {
> > + if (!device_may_wakeup(node->udev->bus->controller))
> > + break;
> > +
> > + if (usb_wakeup_enabled_descendants(node->udev)) {
> > + hub->has_wakeup_capable_descendants = true;
> > + break;
> > + }
> > + }
> > +
> > + mutex_unlock(&hub->lock);
> > +
> > + if (!hub->has_wakeup_capable_descendants)
> > + rc = onboard_hub_power_off(hub);
> > +
> > + return rc;
> > +}
> > +
> > +static int __maybe_unused onboard_hub_resume(struct device *dev)
> > +{
> > + struct onboard_hub *hub = dev_get_drvdata(dev);
> > + int rc = 0;
> > +
> > + if (hub->power_off_in_suspend && !hub->has_wakeup_capable_descendants)
> > + rc = onboard_hub_power_on(hub);
> > +
> > + return rc;
> > +}
> > +
> > +static int onboard_hub_add_usbdev(struct onboard_hub *hub, struct usb_device *udev)
> > +{
> > + struct udev_node *node;
> > +
> > + node = devm_kzalloc(hub->dev, sizeof(*node), GFP_KERNEL);
> > + if (!node)
> > + return -ENOMEM;
> > +
> > + node->udev = udev;
>
> No reference counting? Are you sure about this?
I thought it isn't strictly needed, since this function is only called by the
onboard_hub_usbdev driver, which also calls onboard_hub_remove_usbdev() on
disconnect. So my thinking was that the driver trusts itself, like the kernel.
Am I missing a case?
> > +
> > + mutex_lock(&hub->lock);
> > + list_add(&node->list, &hub->udev_list);
> > + mutex_unlock(&hub->lock);
> > +
> > + return 0;
> > +}
> > +
> > +static int onboard_hub_remove_usbdev(struct onboard_hub *hub, struct usb_device *udev)
> > +{
> > + struct udev_node *node;
> > +
> > + mutex_lock(&hub->lock);
> > +
> > + list_for_each_entry(node, &hub->udev_list, list) {
>
> list_for_each_entry_safe()?
I can change it, but IIUC it shouldn't be really necessary, since the loop
is aborted after removing the node.
> > + if (node->udev == udev) {
> > + list_del(&node->list);
> > + devm_kfree(hub->dev, node);
> > + break;
> > + }
> > + }
> > +
> > + mutex_unlock(&hub->lock);
> > +
> > + if (node == NULL)
> > + return -EINVAL;
> > +
> > + return 0;
> > +}
> > +
> > +static ssize_t power_off_in_suspend_show(struct device *dev, struct device_attribute *attr,
> > + char *buf)
> > +{
> > + struct onboard_hub *hub = dev_get_drvdata(dev);
> > +
> > + return sprintf(buf, "%d\n", hub->power_off_in_suspend);
> > +}
> > +
> > +static ssize_t power_off_in_suspend_store(struct device *dev, struct device_attribute *attr,
> > + const char *buf, size_t count)
> > +{
> > + struct onboard_hub *hub = dev_get_drvdata(dev);
> > + bool val;
> > + int ret;
> > +
> > + ret = strtobool(buf, &val);
>
> You should use kstrtobool() instead, right?
Will change
> > + if (ret < 0)
> > + return ret;
> > +
> > + hub->power_off_in_suspend = val;
> > +
> > + return count;
> > +}
> > +static DEVICE_ATTR_RW(power_off_in_suspend);
> > +
> > +static int onboard_hub_probe(struct platform_device *pdev)
> > +{
> > + struct device *dev = &pdev->dev;
> > + struct onboard_hub *hub;
> > + int rc;
> > +
> > + hub = devm_kzalloc(dev, sizeof(*hub), GFP_KERNEL);
> > + if (!hub)
> > + return -ENOMEM;
> > +
> > + hub->vdd = devm_regulator_get(dev, "vdd");
> > + if (IS_ERR(hub->vdd))
> > + return PTR_ERR(hub->vdd);
> > +
> > + hub->dev = dev;
> > + mutex_init(&hub->lock);
> > + INIT_LIST_HEAD(&hub->udev_list);
> > +
> > + dev_set_drvdata(dev, hub);
> > +
> > + rc = sysfs_create_file(&dev->kobj, &dev_attr_power_off_in_suspend.attr);
>
> Use the default platform device files group, never create/add your own
> sysfs files "by hand", otherwise it could go easily wrong.
Ok
> > + if (rc)
> > + return rc;
> > +
> > + return onboard_hub_power_on(hub);
> > +}
> > +
> > +static int onboard_hub_remove(struct platform_device *pdev)
> > +{
> > + struct onboard_hub *hub = dev_get_drvdata(&pdev->dev);
> > +
> > + sysfs_remove_file(&pdev->dev.kobj, &dev_attr_power_off_in_suspend.attr);
>
> If you do the above, no need to remove this here.
>
> > +
> > + return onboard_hub_power_off(hub);
> > +}
> > +
> > +static const struct of_device_id onboard_hub_match[] = {
> > + { .compatible = "onboard-usb-hub" },
> > + { .compatible = "realtek,rts5411" },
> > + {}
> > +};
> > +MODULE_DEVICE_TABLE(of, onboard_hub_match);
> > +
> > +static SIMPLE_DEV_PM_OPS(onboard_hub_pm_ops, onboard_hub_suspend, onboard_hub_resume);
> > +
> > +static struct platform_driver onboard_hub_driver = {
> > + .probe = onboard_hub_probe,
> > + .remove = onboard_hub_remove,
> > +
> > + .driver = {
> > + .name = "onboard-usb-hub",
> > + .of_match_table = onboard_hub_match,
> > + .pm = pm_ptr(&onboard_hub_pm_ops),
> > + },
> > +};
> > +
> > +/************************** USB driver **************************/
> > +
> > +#define VENDOR_ID_REALTEK 0x0bda
> > +
> > +static struct onboard_hub *_find_onboard_hub(struct device *dev)
> > +{
> > + const phandle *ph;
> > + struct device_node *np;
> > + struct platform_device *pdev;
> > +
> > + ph = of_get_property(dev->of_node, "hub", NULL);
> > + if (!ph) {
> > + dev_err(dev, "failed to read 'hub' property\n");
> > + return ERR_PTR(-EINVAL);
> > + }
> > +
> > + np = of_find_node_by_phandle(be32_to_cpu(*ph));
> > + if (!np) {
> > + dev_err(dev, "failed find device node for onboard hub\n");
> > + return ERR_PTR(-EINVAL);
> > + }
> > +
> > + pdev = of_find_device_by_node(np);
> > + of_node_put(np);
> > + if (!pdev)
> > + return ERR_PTR(-EPROBE_DEFER);
>
> Why can you defer here?
We know there is a node, so if the device can not be found it probably
hasn't been probed yet?
> > +
> > + return dev_get_drvdata(&pdev->dev);
> > +}
> > +
> > +static int onboard_hub_usbdev_probe(struct usb_device *udev)
> > +{
> > + struct device *dev = &udev->dev;
> > + struct onboard_hub *hub;
> > +
> > + /* ignore supported hubs without device tree node */
> > + if (!dev->of_node)
> > + return -ENODEV;
> > +
> > + hub = _find_onboard_hub(dev);
> > + if (IS_ERR(hub))
> > + return PTR_ERR(dev);
> > +
> > + dev_set_drvdata(dev, hub);
> > +
> > + onboard_hub_add_usbdev(hub, udev);
> > +
> > + return 0;
> > +}
> > +
> > +static void onboard_hub_usbdev_disconnect(struct usb_device *udev)
> > +{
> > + struct onboard_hub *hub = dev_get_drvdata(&udev->dev);
> > +
> > + onboard_hub_remove_usbdev(hub, udev);
> > +
> > + put_device(hub->dev);
> > +}
> > +
> > +static const struct usb_device_id onboard_hub_id_table[] = {
> > + { .idVendor = VENDOR_ID_REALTEK,
> > + .idProduct = 0x0411, /* RTS5411 USB 3.0 */
> > + .match_flags = USB_DEVICE_ID_MATCH_DEVICE },
> > + { .idVendor = VENDOR_ID_REALTEK,
> > + .idProduct = 0x5411, /* RTS5411 USB 2.0 */
> > + .match_flags = USB_DEVICE_ID_MATCH_DEVICE },
>
> USB_DEVICE() should be used here instead for both of these, right?
ack
> > + {},
> > +};
> > +
> > +MODULE_DEVICE_TABLE(usb, onboard_hub_id_table);
> > +
> > +static struct usb_device_driver onboard_hub_usbdev_driver = {
> > +
> > + .name = "onboard-usb-hub",
> > + .probe = onboard_hub_usbdev_probe,
> > + .disconnect = onboard_hub_usbdev_disconnect,
> > + .generic_subclass = 1,
> > + .supports_autosuspend = 1,
> > + .id_table = onboard_hub_id_table,
> > +};
> > +
> > +/************************** Driver (de)registration **************************/
> > +
> > +static int __init onboard_hub_init(void)
> > +{
> > + int rc;
> > +
> > + rc = platform_driver_register(&onboard_hub_driver);
> > + if (rc)
> > + return rc;
> > +
> > + return usb_register_device_driver(&onboard_hub_usbdev_driver, THIS_MODULE);
>
> No unwinding of the platform driver register if this fails?
Right, will add unwinding.
> And THIS_MODULE should not be needed, did we get the api wrong here?
It seems you suggest to use usb_register() instead, SGTM
> > +}
> > +device_initcall(onboard_hub_init);
>
> Why device_initcall() if this could be a module? Why not a normal
> module_init()?
Ok, will change it to module_init()
Thanks
Matthias
