Miquel Raynal <miquel.raynal@xxxxxxxxxxx> wrote on Tue, 15 Sep 2020
10:07:28 +0200:
> Hi Yifeng,
>
> I am very sorry for the delay it took me to review this driver, but
> there are still some small incoherences IMHO, see below.
One last important comment below
> > +static int rk_nfc_attach_chip(struct nand_chip *chip)
> > +{
> > + struct mtd_info *mtd = nand_to_mtd(chip);
> > + struct device *dev = mtd->dev.parent;
> > + struct rk_nfc *nfc = nand_get_controller_data(chip);
> > + struct rk_nfc_nand_chip *rknand = to_rknand(chip);
> > + struct nand_ecc_ctrl *ecc = &chip->ecc;
> > + int len;
> > + int ret;
> > +
> > + if (chip->options & NAND_BUSWIDTH_16) {
> > + dev_err(dev, "16 bits bus width not supported");
> > + return -EINVAL;
> > + }
> > +
> > + if (ecc->mode != NAND_ECC_HW)
> > + return 0;
> > +
> > + ret = rk_nfc_ecc_init(dev, mtd);
> > + if (ret)
> > + return ret;
> > + rknand->spare_per_sector = ecc->bytes + NFC_SYS_DATA_SIZE;
> > + rknand->metadata_size = NFC_SYS_DATA_SIZE * ecc->steps;
> > +
> > + if (rknand->metadata_size < NFC_SYS_DATA_SIZE + 2) {
> > + dev_err(dev,
> > + "Driver needs at least %d bytes of meta data\n",
> > + NFC_SYS_DATA_SIZE + 2);
> > + return -EIO;
> > + }
> > + /* Check buffer first, avoid duplicate alloc buffer. */
> > + if (nfc->buffer)
> > + return 0;
>
> You can't do that this way: what if the first mtd to be registered uses
> a smaller page size than the second?
>
> > +
> > + len = mtd->writesize + mtd->oobsize;
> > + nfc->buffer = devm_kzalloc(dev, len, GFP_KERNEL | GFP_DMA);
I don't think this fits your purpose. You should probably allocate with
kzalloc or perhaps dma_alloc*.
Then, you'll also have to free this memory.
> > + if (!nfc->buffer)
> > + return -ENOMEM;
> > +
> > + nfc->page_buf = nfc->buffer;
> > + len = ecc->steps * NFC_MAX_OOB_PER_STEP;
> > + nfc->oob_buf = devm_kzalloc(dev, len, GFP_KERNEL | GFP_DMA);
> > + if (!nfc->oob_buf) {
> > + nfc->buffer = NULL;
> > + nfc->oob_buf = NULL;
>
> I don't think this is needed
>
> > + return -ENOMEM;
> > + }
> > +
> > + chip->ecc.write_page_raw = rk_nfc_write_page_raw;
> > + chip->ecc.write_page = rk_nfc_write_page_hwecc;
> > + chip->ecc.write_oob_raw = rk_nfc_write_oob_std;
> > + chip->ecc.write_oob = rk_nfc_write_oob_std;
> > +
> > + chip->ecc.read_page_raw = rk_nfc_read_page_raw;
> > + chip->ecc.read_page = rk_nfc_read_page_hwecc;
> > + chip->ecc.read_oob_raw = rk_nfc_read_oob_std;
> > + chip->ecc.read_oob = rk_nfc_read_oob_std;
>
> I don't like the _std prefix, but it should be gone when splitting the
> functions as advised.
>
> > +
> > + return 0;
> > +}
Thanks,
Miquèl
