From: Jonathan Cameron <Jonathan.Cameron@xxxxxxxxxx>
Fairly straight conversion. The one oddity in the original binding
is that spi-cpha and spi-cpol were not marked as required, but were
in the example. Looking at the datasheet, there isn't any documented
flexibility in the possible SPI modes, so I have moved these to requires.
For spi-max-frequency I have gone the other way. I absolutely agree
that it is good to specify this in the dt-binding, but it's not
strictly required.
As Stefan's email is bouncing I have gone with Michael as maintainer
of this one as it falls under the ADI catch all entry in MAINTAINERS.
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@xxxxxxxxxx>
Cc: Michael Hennerich <Michael.Hennerich@xxxxxxxxxx>
---
.../bindings/iio/adc/adi,ad7768-1.txt | 41 ---------
.../bindings/iio/adc/adi,ad7768-1.yaml | 89 +++++++++++++++++++
2 files changed, 89 insertions(+), 41 deletions(-)
diff --git a/Documentation/devicetree/bindings/iio/adc/adi,ad7768-1.txt b/Documentation/devicetree/bindings/iio/adc/adi,ad7768-1.txt
deleted file mode 100644
index 9f5b88cf680d..000000000000
--- a/Documentation/devicetree/bindings/iio/adc/adi,ad7768-1.txt
+++ /dev/null
@@ -1,41 +0,0 @@
-Analog Devices AD7768-1 ADC device driver
-
-Required properties for the AD7768-1:
-
-- compatible: Must be "adi,ad7768-1"
-- reg: SPI chip select number for the device
-- spi-max-frequency: Max SPI frequency to use
- see: Documentation/devicetree/bindings/spi/spi-bus.txt
-- clocks: phandle to the master clock (mclk)
- see: Documentation/devicetree/bindings/clock/clock-bindings.txt
-- clock-names: Must be "mclk".
-- interrupts: IRQ line for the ADC
- see: Documentation/devicetree/bindings/interrupt-controller/interrupts.txt
-- vref-supply: vref supply can be used as reference for conversion
-- adi,sync-in-gpios: must be the device tree identifier of the SYNC-IN pin. Enables
- synchronization of multiple devices that require simultaneous sampling.
- A pulse is always required if the configuration is changed in any way, for example
- if the filter decimation rate changes. As the line is active low, it should
- be marked GPIO_ACTIVE_LOW.
-
-Optional properties:
-
- - reset-gpios : GPIO spec for the RESET pin. If specified, it will be asserted during
- driver probe. As the line is active low, it should be marked GPIO_ACTIVE_LOW.
-
-Example:
-
- adc@0 {
- compatible = "adi,ad7768-1";
- reg = <0>;
- spi-max-frequency = <2000000>;
- spi-cpol;
- spi-cpha;
- vref-supply = <&adc_vref>;
- interrupts = <25 IRQ_TYPE_EDGE_RISING>;
- interrupt-parent = <&gpio>;
- adi,sync-in-gpios = <&gpio 22 GPIO_ACTIVE_LOW>;
- reset-gpios = <&gpio 27 GPIO_ACTIVE_LOW>;
- clocks = <&ad7768_mclk>;
- clock-names = "mclk";
- };
diff --git a/Documentation/devicetree/bindings/iio/adc/adi,ad7768-1.yaml b/Documentation/devicetree/bindings/iio/adc/adi,ad7768-1.yaml
new file mode 100644
index 000000000000..d3733ad8785a
--- /dev/null
+++ b/Documentation/devicetree/bindings/iio/adc/adi,ad7768-1.yaml
@@ -0,0 +1,89 @@
+# SPDX-License-Identifier: GPL-2.0
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/iio/adc/adi,ad7768-1.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Analog Devices AD7768-1 ADC device driver
+
+maintainers:
+ - Michael Hennerich <michael.hennerich@xxxxxxxxxx>
+
+description: |
+ Datasheet at:
+ https://www.analog.com/media/en/technical-documentation/data-sheets/ad7768-1.pdf
+
+properties:
+ compatible:
+ const: adi,ad7768-1
+
+ reg:
+ maxItems: 1
+
+ clocks:
+ maxItems: 1
+
+ clock-names:
+ const: mclk
+
+ interrupts:
+ maxItems: 1
+
+ vref-supply:
+ description:
+ ADC reference voltage supply
+
+ adi,sync-in-gpios:
+ description:
+ Enables synchronization of multiple devices that require simultaneous
+ sampling. A pulse is always required if the configuration is changed
+ in any way, for example if the filter decimation rate changes.
+ As the line is active low, it should be marked GPIO_ACTIVE_LOW.
+
+ reset-gpios:
+ maxItems: 1
+
+ spi-max-frequency: true
+
+ spi-cpol: true
+ spi-cpha : true
+
+ "#io-channel-cells":
+ const: 1
+
+required:
+ - compatible
+ - reg
+ - clocks
+ - clock-names
+ - vref-supply
+ - spi-cpol
+ - spi-cpha
+ - adi,sync-in-gpios
+
+additionalProperties: false
+
+examples:
+ - |
+ #include <dt-bindings/interrupt-controller/irq.h>
+ #include <dt-bindings/gpio/gpio.h>
+ spi {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ adc@0 {
+ compatible = "adi,ad7768-1";
+ reg = <0>;
+ spi-max-frequency = <2000000>;
+ spi-cpol;
+ spi-cpha;
+ vref-supply = <&adc_vref>;
+ interrupts = <25 IRQ_TYPE_EDGE_RISING>;
+ interrupt-parent = <&gpio>;
+ adi,sync-in-gpios = <&gpio 22 GPIO_ACTIVE_LOW>;
+ reset-gpios = <&gpio 27 GPIO_ACTIVE_LOW>;
+ clocks = <&ad7768_mclk>;
+ clock-names = "mclk";
+ };
+ };
+...
--
2.28.0
