Re: [PATCH V4 1/4] arm64: dts: sc7180: Add wakeup support over UART RX

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



Hi Matthias,

On 2020-09-03 21:35, Matthias Kaehlcke wrote:
On Thu, Sep 03, 2020 at 08:34:55PM +0530, satya priya wrote:
Add the necessary pinctrl and interrupts to make UART wakeup capable.

If QUP function is selected in sleep state, UART RTS/RFR is pulled high
during suspend and BT SoC not able to send wakeup bytes. So, configure
GPIO mode in sleep state to keep it low during suspend.

Signed-off-by: satya priya <skakit@xxxxxxxxxxxxxx>
Reviewed-by: Akash Asthana <akashast@xxxxxxxxxxxxxx>
---
Changes in V2:
 - As per Matthias's comment added wakeup support for all the UARTs
   of SC7180.

Changes in V3:
 - No change.

Changes in V4:
 - As per Matthias's comment, added the reason for configuring GPIO
   mode for sleep state in commit text.

arch/arm64/boot/dts/qcom/sc7180.dtsi | 98 ++++++++++++++++++++++++++++++------
 1 file changed, 84 insertions(+), 14 deletions(-)

diff --git a/arch/arm64/boot/dts/qcom/sc7180.dtsi b/arch/arm64/boot/dts/qcom/sc7180.dtsi
index d46b383..855b13e 100644
--- a/arch/arm64/boot/dts/qcom/sc7180.dtsi
+++ b/arch/arm64/boot/dts/qcom/sc7180.dtsi
@@ -793,9 +793,11 @@
 				reg = <0 0x00880000 0 0x4000>;
 				clock-names = "se";
 				clocks = <&gcc GCC_QUPV3_WRAP0_S0_CLK>;
-				pinctrl-names = "default";
+				pinctrl-names = "default", "sleep";
 				pinctrl-0 = <&qup_uart0_default>;
-				interrupts = <GIC_SPI 601 IRQ_TYPE_LEVEL_HIGH>;
+				pinctrl-1 = <&qup_uart0_sleep>;
+				interrupts-extended = <&intc GIC_SPI 601 IRQ_TYPE_LEVEL_HIGH>,
+							<&tlmm 37 IRQ_TYPE_EDGE_FALLING>;
 				power-domains = <&rpmhpd SC7180_CX>;
 				operating-points-v2 = <&qup_opp_table>;
interconnects = <&qup_virt MASTER_QUP_CORE_0 &qup_virt SLAVE_QUP_CORE_0>,
@@ -845,9 +847,11 @@
 				reg = <0 0x00884000 0 0x4000>;
 				clock-names = "se";
 				clocks = <&gcc GCC_QUPV3_WRAP0_S1_CLK>;
-				pinctrl-names = "default";
+				pinctrl-names = "default", "sleep";
 				pinctrl-0 = <&qup_uart1_default>;
-				interrupts = <GIC_SPI 602 IRQ_TYPE_LEVEL_HIGH>;
+				pinctrl-1 = <&qup_uart1_sleep>;
+				interrupts-extended = <&intc GIC_SPI 602 IRQ_TYPE_LEVEL_HIGH>,
+							<&tlmm 3 IRQ_TYPE_EDGE_FALLING>;
 				power-domains = <&rpmhpd SC7180_CX>;
 				operating-points-v2 = <&qup_opp_table>;
interconnects = <&qup_virt MASTER_QUP_CORE_0 &qup_virt SLAVE_QUP_CORE_0>,
@@ -931,9 +935,11 @@
 				reg = <0 0x0088c000 0 0x4000>;
 				clock-names = "se";
 				clocks = <&gcc GCC_QUPV3_WRAP0_S3_CLK>;
-				pinctrl-names = "default";
+				pinctrl-names = "default", "sleep";
 				pinctrl-0 = <&qup_uart3_default>;
-				interrupts = <GIC_SPI 604 IRQ_TYPE_LEVEL_HIGH>;
+				pinctrl-1 = <&qup_uart3_sleep>;
+				interrupts-extended = <&intc GIC_SPI 604 IRQ_TYPE_LEVEL_HIGH>,
+							<&tlmm 41 IRQ_TYPE_EDGE_FALLING>;
 				power-domains = <&rpmhpd SC7180_CX>;
 				operating-points-v2 = <&qup_opp_table>;
interconnects = <&qup_virt MASTER_QUP_CORE_0 &qup_virt SLAVE_QUP_CORE_0>,
@@ -1017,9 +1023,11 @@
 				reg = <0 0x00894000 0 0x4000>;
 				clock-names = "se";
 				clocks = <&gcc GCC_QUPV3_WRAP0_S5_CLK>;
-				pinctrl-names = "default";
+				pinctrl-names = "default", "sleep";
 				pinctrl-0 = <&qup_uart5_default>;
-				interrupts = <GIC_SPI 606 IRQ_TYPE_LEVEL_HIGH>;
+				pinctrl-1 = <&qup_uart5_sleep>;
+				interrupts-extended = <&intc GIC_SPI 606 IRQ_TYPE_LEVEL_HIGH>,
+							<&tlmm 28 IRQ_TYPE_EDGE_FALLING>;
 				power-domains = <&rpmhpd SC7180_CX>;
 				operating-points-v2 = <&qup_opp_table>;
interconnects = <&qup_virt MASTER_QUP_CORE_0 &qup_virt SLAVE_QUP_CORE_0>,
@@ -1084,9 +1092,11 @@
 				reg = <0 0x00a80000 0 0x4000>;
 				clock-names = "se";
 				clocks = <&gcc GCC_QUPV3_WRAP1_S0_CLK>;
-				pinctrl-names = "default";
+				pinctrl-names = "default", "sleep";
 				pinctrl-0 = <&qup_uart6_default>;
-				interrupts = <GIC_SPI 353 IRQ_TYPE_LEVEL_HIGH>;
+				pinctrl-1 = <&qup_uart6_sleep>;
+				interrupts-extended = <&intc GIC_SPI 353 IRQ_TYPE_LEVEL_HIGH>,
+							<&tlmm 62 IRQ_TYPE_EDGE_FALLING>;
 				power-domains = <&rpmhpd SC7180_CX>;
 				operating-points-v2 = <&qup_opp_table>;
interconnects = <&qup_virt MASTER_QUP_CORE_1 &qup_virt SLAVE_QUP_CORE_1>,
@@ -1256,9 +1266,11 @@
 				reg = <0 0x00a90000 0 0x4000>;
 				clock-names = "se";
 				clocks = <&gcc GCC_QUPV3_WRAP1_S4_CLK>;
-				pinctrl-names = "default";
+				pinctrl-names = "default", "sleep";
 				pinctrl-0 = <&qup_uart10_default>;
-				interrupts = <GIC_SPI 357 IRQ_TYPE_LEVEL_HIGH>;
+				pinctrl-1 = <&qup_uart10_sleep>;
+				interrupts-extended = <&intc GIC_SPI 357 IRQ_TYPE_LEVEL_HIGH>,
+							<&tlmm 89 IRQ_TYPE_EDGE_FALLING>;
 				power-domains = <&rpmhpd SC7180_CX>;
 				operating-points-v2 = <&qup_opp_table>;
interconnects = <&qup_virt MASTER_QUP_CORE_1 &qup_virt SLAVE_QUP_CORE_1>,
@@ -1308,9 +1320,11 @@
 				reg = <0 0x00a94000 0 0x4000>;
 				clock-names = "se";
 				clocks = <&gcc GCC_QUPV3_WRAP1_S5_CLK>;
-				pinctrl-names = "default";
+				pinctrl-names = "default", "sleep";
 				pinctrl-0 = <&qup_uart11_default>;
-				interrupts = <GIC_SPI 358 IRQ_TYPE_LEVEL_HIGH>;
+				pinctrl-1 = <&qup_uart11_sleep>;
+				interrupts-extended = <&intc GIC_SPI 358 IRQ_TYPE_LEVEL_HIGH>,
+							<&tlmm 56 IRQ_TYPE_EDGE_FALLING>;
 				power-domains = <&rpmhpd SC7180_CX>;
 				operating-points-v2 = <&qup_opp_table>;
interconnects = <&qup_virt MASTER_QUP_CORE_1 &qup_virt SLAVE_QUP_CORE_1>,
@@ -1638,6 +1652,14 @@
 				};
 			};

+			qup_uart0_sleep: qup-uart0-sleep {
+				pinmux {
+					pins = "gpio34", "gpio35",
+					       "gpio36", "gpio37";
+					function = "gpio";
+				};
+			};
+
 			qup_uart1_default: qup-uart1-default {
 				pinmux {
 					pins = "gpio0", "gpio1",
@@ -1646,6 +1668,14 @@
 				};
 			};

+			qup_uart1_sleep: qup-uart1-sleep {
+				pinmux {
+					pins = "gpio0", "gpio1",
+					       "gpio2", "gpio3";
+					function = "gpio";
+				};
+			};
+
 			qup_uart2_default: qup-uart2-default {
 				pinmux {
 					pins = "gpio15", "gpio16";
@@ -1661,6 +1691,14 @@
 				};
 			};

+			qup_uart3_sleep: qup-uart3-sleep {
+				pinmux {
+					pins = "gpio38", "gpio39",
+					       "gpio40", "gpio41";
+					function = "gpio";
+				};
+			};
+
 			qup_uart4_default: qup-uart4-default {
 				pinmux {
 					pins = "gpio115", "gpio116";
@@ -1676,6 +1714,14 @@
 				};
 			};

+			qup_uart5_sleep: qup-uart5-sleep {
+				pinmux {
+					pins = "gpio25", "gpio26",
+					       "gpio27", "gpio28";
+					function = "gpio";
+				};
+			};
+
 			qup_uart6_default: qup-uart6-default {
 				pinmux {
 					pins = "gpio59", "gpio60",
@@ -1684,6 +1730,14 @@
 				};
 			};

+			qup_uart6_sleep: qup-uart6-sleep {
+				pinmux {
+					pins = "gpio59", "gpio60",
+					       "gpio61", "gpio62";
+					function = "gpio";
+				};
+			};
+
 			qup_uart7_default: qup-uart7-default {
 				pinmux {
 					pins = "gpio6", "gpio7";
@@ -1713,6 +1767,14 @@
 				};
 			};

+			qup_uart10_sleep: qup-uart10-sleep {
+				pinmux {
+					pins = "gpio86", "gpio87",
+					       "gpio88", "gpio89";
+					function = "gpio";
+				};
+			};
+
 			qup_uart11_default: qup-uart11-default {
 				pinmux {
 					pins = "gpio53", "gpio54",
@@ -1721,6 +1783,14 @@
 				};
 			};

+			qup_uart11_sleep: qup-uart11-sleep {
+				pinmux {
+					pins = "gpio53", "gpio54",
+					       "gpio55", "gpio56";
+					function = "gpio";
+				};
+			};
+
 			sdc1_on: sdc1-on {
 				pinconf-clk {
 					pins = "sdc1_clk";

It seems only the RTS pin actually requires a pinmux change. One could
argue that only the muxing of this pin should be changed in sleep mode.
But well, changing all pins to GPIO simplifies the config, so I guess
it's ok as long as there are no side effects.

I noticed you changed only the UARTs that have RTS/CTS signals. Do the
others not support wakeup? I understand that the pinmux change isn't
needed for these UARTs, since they have no RTS signal, however I'd expect
them to need the 'interrupts-extended' entry if they support wakeup.

We are planning to add the wakeup related changes(interrupts-extended, pin ctrls) to only uart3 in board specific file. As we understand, this wakeup is an optional feature and cannot be added to all the UARTs. So, now all the changes will be added in board specific files including the pinmux change for sleep state.

Thanks,
Satya Priya




[Index of Archives]     [Device Tree Compilter]     [Device Tree Spec]     [Linux Driver Backports]     [Video for Linux]     [Linux USB Devel]     [Linux PCI Devel]     [Linux Audio Users]     [Linux Kernel]     [Linux SCSI]     [XFree86]     [Yosemite Backpacking]


  Powered by Linux