Using full paths to extend or override a device tree node is error prone
since if there was a typo error, a new node will be created instead of
extending the node as it was desired. This will lead to run-time errors
that could be hard to detect.
A mistyped label on the other hand, will cause a dtc compile error
(during build time).
Signed-off-by: Krzysztof Kozlowski <krzk@xxxxxxxxxx>
---
.../boot/dts/exynos4412-odroid-common.dtsi | 34 ++++++--------
arch/arm/boot/dts/exynos4412-odroidu3.dts | 46 +++++++++----------
2 files changed, 36 insertions(+), 44 deletions(-)
diff --git a/arch/arm/boot/dts/exynos4412-odroid-common.dtsi b/arch/arm/boot/dts/exynos4412-odroid-common.dtsi
index 6d3576e21ffa..ca3c78e0966c 100644
--- a/arch/arm/boot/dts/exynos4412-odroid-common.dtsi
+++ b/arch/arm/boot/dts/exynos4412-odroid-common.dtsi
@@ -66,25 +66,6 @@
clock-frequency = <24000000>;
};
};
-
- thermal-zones {
- cpu_thermal: cpu-thermal {
- cooling-maps {
- cooling_map0: map0 {
- /* Corresponds to 800MHz at freq_table */
- cooling-device = <&cpu0 7 7>, <&cpu1 7 7>,
- <&cpu2 7 7>, <&cpu3 7 7>;
- };
- cooling_map1: map1 {
- /* Corresponds to 200MHz at freq_table */
- cooling-device = <&cpu0 13 13>,
- <&cpu1 13 13>,
- <&cpu2 13 13>,
- <&cpu3 13 13>;
- };
- };
- };
- };
};
&bus_dmc {
@@ -172,6 +153,21 @@
};
};
+&cpu_thermal {
+ cooling-maps {
+ cooling_map0: map0 {
+ /* Corresponds to 800MHz at freq_table */
+ cooling-device = <&cpu0 7 7>, <&cpu1 7 7>,
+ <&cpu2 7 7>, <&cpu3 7 7>;
+ };
+ cooling_map1: map1 {
+ /* Corresponds to 200MHz at freq_table */
+ cooling-device = <&cpu0 13 13>, <&cpu1 13 13>,
+ <&cpu2 13 13>, <&cpu3 13 13>;
+ };
+ };
+};
+
&pinctrl_1 {
gpio_power_key: power_key {
samsung,pins = "gpx1-3";
diff --git a/arch/arm/boot/dts/exynos4412-odroidu3.dts b/arch/arm/boot/dts/exynos4412-odroidu3.dts
index 8ff243ba4542..b8549d846f86 100644
--- a/arch/arm/boot/dts/exynos4412-odroidu3.dts
+++ b/arch/arm/boot/dts/exynos4412-odroidu3.dts
@@ -37,31 +37,6 @@
#cooling-cells = <2>;
cooling-levels = <0 102 170 230>;
};
-
- thermal-zones {
- cpu_thermal: cpu-thermal {
- cooling-maps {
- map0 {
- trip = <&cpu_alert1>;
- cooling-device = <&cpu0 9 9>, <&cpu1 9 9>,
- <&cpu2 9 9>, <&cpu3 9 9>,
- <&fan0 1 2>;
- };
- map1 {
- trip = <&cpu_alert2>;
- cooling-device = <&cpu0 15 15>,
- <&cpu1 15 15>,
- <&cpu2 15 15>,
- <&cpu3 15 15>,
- <&fan0 2 3>;
- };
- map2 {
- trip = <&cpu_alert0>;
- cooling-device = <&fan0 0 1>;
- };
- };
- };
- };
};
&adc {
@@ -76,6 +51,27 @@
regulator-max-microvolt = <3300000>;
};
+&cpu_thermal {
+ cooling-maps {
+ map0 {
+ trip = <&cpu_alert1>;
+ cooling-device = <&cpu0 9 9>, <&cpu1 9 9>,
+ <&cpu2 9 9>, <&cpu3 9 9>,
+ <&fan0 1 2>;
+ };
+ map1 {
+ trip = <&cpu_alert2>;
+ cooling-device = <&cpu0 15 15>, <&cpu1 15 15>,
+ <&cpu2 15 15>, <&cpu3 15 15>,
+ <&fan0 2 3>;
+ };
+ map2 {
+ trip = <&cpu_alert0>;
+ cooling-device = <&fan0 0 1>;
+ };
+ };
+};
+
&hdmicec {
needs-hpd;
};
--
2.17.1
