Peter,
On 26/08/2020 11:07, Peter Chen wrote:
On 20-08-26 04:04:01, Pawel Laszczak wrote:
On 20-08-25 15:00:59, Roger Quadros wrote:
From: Pawel Laszczak <pawell@xxxxxxxxxxx>
USB2.0 PHY hangs in Rx Compliance test when the incoming packet
amplitude is varied below and above the Squelch Level of Receiver
during the active packet multiple times.
Version 1 of the controller allows PHY to be reset when RX fail
condition is detected to work around the above issue. This feature
is disabled by default and needs to be enabled using a bit from
the newly added PHYRST_CFG register. This patch enables the workaround.
As there is no way to distinguish between the controller version
before the device controller is started we need to rely on a DT
property to decide when to apply the workaround.
Pawel, it could know the controller version at cdns3_gadget_start,
but the controller starts when it tries to bind gadget driver, at
that time, it has already known the controller version.
For me, the device controller starts is using USB_CONF.DEVEN (Device
Enable) through usb_gadget_connect, I am not sure if it is the same
with yours.
Yes in device mode driver knows controller version but this
workaround Must be enabled also in host mode. In host mode the
controller doesn't have access to device registers. The controller
version is placed in device register.
You may suggest your design team adding CHIP_VER register at global
register region, it will easy the software engineer life.
>From what I read, this register is only enabling USB2 PHY reset
software control, it needs for all chips with rev 0x0002450D, and the
place you current change is only for 0x0002450D, right?
Even I could say that this workaround should be enabled only for Specific USB2
PHY (only 0x0002450D)
This bit should not have any impact for Cadence PHY but it can has Impact for third
party PHYs.
So, it is related to specific PHY, but enable this specific PHY reset bit is at controller region, why don't
put this enable bit at PHY region?
I think this is related to Controller + PHY combination.
The fix for the issue is via a bit in the controller, so it needs to be managed by the
controller driver.
So, you use controller's device property to know this specific PHY, can controller know this specific
PHY dynamically?
Still the PHY will have to tell the controller the enable that bit. How to do that?
Adding a dt-property that vendors can used was the simplest option.
cheers,
-roger
Peter
Pawel
Peter
Pawel
Peter
Signed-off-by: Pawel Laszczak <pawell@xxxxxxxxxxx>
Signed-off-by: Roger Quadros <rogerq@xxxxxx>
---
drivers/usb/cdns3/core.c | 2 ++
drivers/usb/cdns3/core.h | 1 +
drivers/usb/cdns3/drd.c | 12 ++++++++++++
drivers/usb/cdns3/drd.h | 5 ++++-
4 files changed, 19 insertions(+), 1 deletion(-)
diff --git a/drivers/usb/cdns3/core.c b/drivers/usb/cdns3/core.c
index 5c1586ec7824..34b36487682b 100644
--- a/drivers/usb/cdns3/core.c
+++ b/drivers/usb/cdns3/core.c
@@ -443,6 +443,8 @@ static int cdns3_probe(struct platform_device *pdev)
return -ENXIO;
}
+ cdns->phyrst_a_enable = device_property_read_bool(dev,
+"cdns,phyrst-a-enable");
+
cdns->otg_res = *res;
mutex_init(&cdns->mutex);
diff --git a/drivers/usb/cdns3/core.h b/drivers/usb/cdns3/core.h
index 1ad1f1fe61e9..24cf0f1b5726 100644
--- a/drivers/usb/cdns3/core.h
+++ b/drivers/usb/cdns3/core.h
@@ -76,6 +76,7 @@ struct cdns3 {
#define CDNS3_CONTROLLER_V0 0
#define CDNS3_CONTROLLER_V1 1
u32 version;
+ bool phyrst_a_enable;
int otg_irq;
int dev_irq;
diff --git a/drivers/usb/cdns3/drd.c b/drivers/usb/cdns3/drd.c
index 6234bcd6158a..b74803e9703d 100644
--- a/drivers/usb/cdns3/drd.c
+++ b/drivers/usb/cdns3/drd.c
@@ -42,6 +42,18 @@ int cdns3_set_mode(struct cdns3 *cdns, enum
usb_dr_mode mode)
reg = readl(&cdns->otg_v1_regs->override);
reg |= OVERRIDE_IDPULLUP;
writel(reg, &cdns->otg_v1_regs->override);
+
+ /*
+ * Enable work around feature built into the
+ * controller to address issue with RX Sensitivity
+ * est (EL_17) for USB2 PHY. The issue only occures
+ * for 0x0002450D controller version.
+ */
+ if (cdns->phyrst_a_enable) {
+ reg = readl(&cdns->otg_v1_regs->phyrst_cfg);
+ reg |= PHYRST_CFG_PHYRST_A_ENABLE;
+ writel(reg, &cdns->otg_v1_regs->phyrst_cfg);
+ }
} else {
reg = readl(&cdns->otg_v0_regs->ctrl1);
reg |= OVERRIDE_IDPULLUP_V0;
diff --git a/drivers/usb/cdns3/drd.h b/drivers/usb/cdns3/drd.h
index 7e7cf7fa2dd3..f1ccae285a16 100644
--- a/drivers/usb/cdns3/drd.h
+++ b/drivers/usb/cdns3/drd.h
@@ -31,7 +31,7 @@ struct cdns3_otg_regs {
__le32 simulate;
__le32 override;
__le32 susp_ctrl;
- __le32 reserved4;
+ __le32 phyrst_cfg;
__le32 anasts;
__le32 adp_ramp_time;
__le32 ctrl1;
@@ -153,6 +153,9 @@ struct cdns3_otg_common_regs {
/* Only for CDNS3_CONTROLLER_V0 version */
#define OVERRIDE_IDPULLUP_V0 BIT(24)
+/* PHYRST_CFG - bitmasks */
+#define PHYRST_CFG_PHYRST_A_ENABLE BIT(0)
+
#define CDNS3_ID_PERIPHERAL 1
#define CDNS3_ID_HOST 0
--
Texas Instruments Finland Oy, Porkkalankatu 22, 00180 Helsinki.
Y-tunnus/Business ID: 0615521-4. Kotipaikka/Domicile: Helsinki
--
Thanks,
Peter Chen
--
Thanks,
Peter Chen
--
Texas Instruments Finland Oy, Porkkalankatu 22, 00180 Helsinki.
Y-tunnus/Business ID: 0615521-4. Kotipaikka/Domicile: Helsinki
