[PATCH v5 0/2] Add PWM support for Intel Keem Bay SoC

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



From: "Vineetha G. Jaya Kumaran" <vineetha.g.jaya.kumaran@xxxxxxxxx>

Hi,

This patch set enables support for PWM on the Intel Keem Bay SoC.
Keem Bay is an ARM based SoC, and the GPIO module allows
configuration of 6 PWM outputs. Patch 1 adds the PWM driver and
Patch 2 is for the required Device Tree bindings documentation.

This driver was tested on the Keem Bay evaluation module board.

Thank you.

Best regards,
Vineetha

Changes since v4:
-Add co-developed-by tag
-Include mod_devicetable.h and remove of.h
-Update comment with correct calulation for high/low time
-Fix missing return from dev_err_probe

Changes since v3:
-Removed variable for address and calculate in place instead
-Utilized u32_replace_bits() when updating KMB_PWM_LEADIN_OFFSET
-Utilized dev_err_probe() for error reporting
-Updated comments to use physical units
-Updated error check for pwmchip_add()

Changes since v2:
-Include documentation about HW limitation/behaviour
-Use hex values for KMB_PWM_COUNT_MAX
-Redefine register macros
-Utilize FIELD_GET/FIELD_PREP for calculating pwm_l/h_count and pwm_count
-Round up duty cycle/period values
-Get current hardware state in .apply instead of cached values
-Do a polarity check before .enabled
-Round high time/low time to closest value
-Set enable bit in KMB_PWM_LEADIN_OFFSET to 0 in probe
-Correct the naming for MODULE_ALIAS
-Add additionalProperties: false in DT bindings

Changes since v1:
-Updated licensing info, "clocks" property and example in DT bindings
-Updated name of DT bindings document to match compatible string
-Removed 1 patch for addition of new sysfs attribute "count"
-Added support for COMPILE_TEST in Kconfig
-Updated naming of defines and regmap attribute
-Updated calculation of waveform high time and low time
-Added range checking for waveform high/low time
-Implemented .get_state
-Removed register writes for lead-in and count values (left to default)
-Updated register access to single-access
-Folded keembay_pwm_enable/disable_channel, keembay_pwm_config_period/duty_cycle,
 and keembay_pwm_config into keembay_pwm_apply
-Updated error messages/error codes
-Removed pwm_disable from keembay_pwm_remove
-Removed clk_prepare/clk_enable/clk_disable from driver

Lai, Poey Seng (1):
  pwm: Add PWM driver for Intel Keem Bay

Vineetha G. Jaya Kumaran (1):
  dt-bindings: pwm: keembay: Add bindings for Intel Keem Bay PWM

 .../devicetree/bindings/pwm/intel,keembay-pwm.yaml |  47 +++++
 drivers/pwm/Kconfig                                |   9 +
 drivers/pwm/Makefile                               |   1 +
 drivers/pwm/pwm-keembay.c                          | 228 +++++++++++++++++++++
 4 files changed, 285 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/pwm/intel,keembay-pwm.yaml
 create mode 100644 drivers/pwm/pwm-keembay.c

-- 
1.9.1




[Index of Archives]     [Device Tree Compilter]     [Device Tree Spec]     [Linux Driver Backports]     [Video for Linux]     [Linux USB Devel]     [Linux PCI Devel]     [Linux Audio Users]     [Linux Kernel]     [Linux SCSI]     [XFree86]     [Yosemite Backpacking]


  Powered by Linux