Re: [PATCH 2/2] tty: pl011: Add support for xilinx uart

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



On Wed, Aug 19, 2020 at 10:13:59PM +0530, Shubhrajyoti Datta wrote:
> Xilinx uart is similar to sbsa but it has configurable
> parity and hardware flow. Add a compatible for the same.
> 
> Signed-off-by: Shubhrajyoti Datta <shubhrajyoti.datta@xxxxxxxxxx>
> ---
>  drivers/tty/serial/amba-pl011.c | 77 ++++++++++++++++++++++++++++++++++++++++-
>  1 file changed, 76 insertions(+), 1 deletion(-)
> 
> diff --git a/drivers/tty/serial/amba-pl011.c b/drivers/tty/serial/amba-pl011.c
> index 8efd7c2..41dbcee 100644
> --- a/drivers/tty/serial/amba-pl011.c
> +++ b/drivers/tty/serial/amba-pl011.c
> @@ -2073,6 +2073,55 @@ sbsa_uart_set_termios(struct uart_port *port, struct ktermios *termios,
>  	spin_unlock_irqrestore(&port->lock, flags);
>  }
>  
> +static void
> +xlnx_sbsa_uart_set_termios(struct uart_port *port, struct ktermios *termios,
> +			   struct ktermios *old)
> +{
> +	struct uart_amba_port *uap =
> +	    container_of(port, struct uart_amba_port, port);
> +	unsigned long flags;
> +	unsigned int lcr_h, old_cr;
> +
> +	tty_termios_encode_baud_rate(termios, uap->fixed_baud, uap->fixed_baud);
> +	/* The SBSA UART only supports 8n1 without hardware flow control. */
> +	termios->c_cflag &= ~(CMSPAR | CRTSCTS);
> +	switch (termios->c_cflag & CSIZE) {
> +	case CS5:
> +		lcr_h = UART01x_LCRH_WLEN_5;
> +		break;
> +	case CS6:
> +		lcr_h = UART01x_LCRH_WLEN_6;
> +		break;
> +	case CS7:
> +		lcr_h = UART01x_LCRH_WLEN_7;
> +		break;
> +	default:
> +		lcr_h = UART01x_LCRH_WLEN_8;
> +		break;
> +	}
> +	if (termios->c_cflag & CSTOPB)
> +		lcr_h |= UART01x_LCRH_STP2;
> +	if (termios->c_cflag & PARENB) {
> +		lcr_h |= UART01x_LCRH_PEN;
> +		if (!(termios->c_cflag & PARODD))
> +			lcr_h |= UART01x_LCRH_EPS;
> +		if (termios->c_cflag & CMSPAR)
> +			lcr_h |= UART011_LCRH_SPS;
> +	}
> +	if (uap->fifosize > 1)
> +		lcr_h |= UART01x_LCRH_FEN;

I'm guessing at least some of the above code is just copy-n-paste from 
the pl011 version? Can't you reuse the existing version?

> +	spin_lock_irqsave(&port->lock, flags);
> +	uart_update_timeout(port, CS8, uap->fixed_baud);
> +	pl011_setup_status_masks(port, termios);
> +	/* first, disable everything */
> +	old_cr = pl011_read(uap, REG_CR);
> +	pl011_write(0, uap, REG_CR);
> +	pl011_write_lcr_h(uap, lcr_h);
> +	pl011_write(old_cr, uap, REG_CR);
> +	spin_unlock_irqrestore(&port->lock, flags);
> +}
> +
>  static const char *pl011_type(struct uart_port *port)
>  {
>  	struct uart_amba_port *uap =
> @@ -2179,6 +2228,28 @@ static const struct uart_ops sbsa_uart_pops = {
>  #endif
>  };
>  
> +static const struct uart_ops xlnx_sbsa_uart_pops = {
> +	.tx_empty	= pl011_tx_empty,
> +	.set_mctrl	= sbsa_uart_set_mctrl,
> +	.get_mctrl	= sbsa_uart_get_mctrl,
> +	.stop_tx	= pl011_stop_tx,
> +	.start_tx	= pl011_start_tx,
> +	.stop_rx	= pl011_stop_rx,
> +	.startup	= sbsa_uart_startup,
> +	.shutdown	= sbsa_uart_shutdown,
> +	.set_termios	= xlnx_sbsa_uart_set_termios,
> +	.type		= pl011_type,
> +	.release_port	= pl011_release_port,
> +	.request_port	= pl011_request_port,
> +	.config_port	= pl011_config_port,
> +	.verify_port	= pl011_verify_port,
> +#ifdef CONFIG_CONSOLE_POLL
> +	.poll_init     = pl011_hwinit,
> +	.poll_get_char = pl011_get_poll_char,
> +	.poll_put_char = pl011_put_poll_char,
> +#endif
> +};
> +
>  static struct uart_amba_port *amba_ports[UART_NR];
>  
>  #ifdef CONFIG_SERIAL_AMBA_PL011_CONSOLE
> @@ -2754,7 +2825,10 @@ static int sbsa_uart_probe(struct platform_device *pdev)
>  	uap->reg_offset	= uap->vendor->reg_offset;
>  	uap->fifosize	= 32;
>  	uap->port.iotype = uap->vendor->access_32b ? UPIO_MEM32 : UPIO_MEM;
> -	uap->port.ops	= &sbsa_uart_pops;
> +	if (of_device_is_compatible(pdev->dev.of_node, "arm,xlnx-sbsa-uart"))
> +		uap->port.ops	= &xlnx_sbsa_uart_pops;
> +	else
> +		uap->port.ops	= &sbsa_uart_pops;
>  	uap->fixed_baud = baudrate;
>  
>  	snprintf(uap->type, sizeof(uap->type), "SBSA");
> @@ -2781,6 +2855,7 @@ static int sbsa_uart_remove(struct platform_device *pdev)
>  
>  static const struct of_device_id sbsa_uart_of_match[] = {
>  	{ .compatible = "arm,sbsa-uart", },
> +	{ .compatible = "arm,xlnx-sbsa-uart", },
>  	{},
>  };
>  MODULE_DEVICE_TABLE(of, sbsa_uart_of_match);
> -- 
> 2.7.4
> 



[Index of Archives]     [Device Tree Compilter]     [Device Tree Spec]     [Linux Driver Backports]     [Video for Linux]     [Linux USB Devel]     [Linux PCI Devel]     [Linux Audio Users]     [Linux Kernel]     [Linux SCSI]     [XFree86]     [Yosemite Backpacking]


  Powered by Linux