Re: [PATCH v5 9/9] arm64: dts: renesas: salvator: add a connection from adv748x codec (HDMI input) to the R-Car SoC

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



Hi Alex,

On 18/06/2020 17:32, Kieran Bingham wrote:
> Hi Alex,
> 
> On 02/04/2020 19:35, Alex Riesen wrote:
>> As all known variants of the Salvator board have the HDMI decoder
>> chip (the ADV7482) connected to the SSI4 on R-Car SoC, the ADV7482
>> endpoint and the connection definitions are placed in the common board
>> file.
>>
>> For the same reason, the CLK_C clock line and I2C configuration (similar
>> to the ak4613, on the same interface) are added into the common file.
>>
>> Signed-off-by: Alexander Riesen <alexander.riesen@xxxxxxxxxxx>
>>
>> --
>>
>> v5: Add dummy ssi4 node to the rcar sound card in r8a77961, as the
>>     devices (Salvator-X 2nd version with R-Car M3 W+) also reference
>>     salvator-common.dtsi.
>>     Suggested-by: Geert Uytterhoeven <geert@xxxxxxxxxxxxxx>
>>
>> v2: Also add ssi4_ctrl pin group in the sound pins. The pins are
>>     responsible for SCK4 (sample clock) WS4 and (word boundary input),
>>     and are required for SSI audio input over I2S.
>>
>>     The adv748x shall provide its own implementation of the output clock
>>     (MCLK), connected to the audio_clk_c line of the R-Car SoC.
>>
>>     If the frequency of the ADV748x MCLK were fixed, the clock
>>     implementation were not necessary, but it does not seem so: the MCLK
>>     depends on the value in a speed multiplier register and the input sample
>>     rate (48kHz).
>>
>>     Remove audio clock C from the clocks of adv7482.
>>
>>     The clocks property of the video-receiver node lists the input
>>     clocks of the device, which is quite the opposite from the
>>     original intention: the adv7482 on Salvator X boards is a
>>     provide of the MCLK clock for I2S audio output.
>>
>>     Remove old definition of &sound_card.dais and reduce size of changes
>>     in the Salvator-X specific device tree source.
>>
>>     Declare video-receiver a clock producer, as the adv748x driver
>>     implements the master clock used I2S audio output.
>>
>>     Suggested-by: Geert Uytterhoeven <geert@xxxxxxxxxxxxxx>
>>
>> v2: The driver provides only MCLK clock, not the SCLK and LRCLK,
>>     which are part of the I2S protocol.
>>
>>     Suggested-by: Laurent Pinchart <laurent.pinchart@xxxxxxxxxxxxxxxx>
>> ---
>>  .../boot/dts/renesas/r8a77950-salvator-x.dts  |  3 +-
>>  arch/arm64/boot/dts/renesas/r8a77961.dtsi     |  1 +
>>  .../boot/dts/renesas/salvator-common.dtsi     | 47 +++++++++++++++++--

Once again I'm back trying to test this series, and one issue I've had
is that the board I have (r8a77951-salvator-xs.dts) isn't included in
this DT update.

For v6, Should we include the relevant changes to all the following?

arch/arm64/boot/dts/renesas/r8a77950-salvator-x.dts
arch/arm64/boot/dts/renesas/r8a77951-salvator-x.dts
arch/arm64/boot/dts/renesas/r8a77960-salvator-x.dts
arch/arm64/boot/dts/renesas/r8a77965-salvator-x.dts
arch/arm64/boot/dts/renesas/salvator-x.dtsi

And perhaps handle the salvator-xs in a second (yet very similar) patch?

arch/arm64/boot/dts/renesas/r8a77951-salvator-xs.dts
arch/arm64/boot/dts/renesas/r8a77960-salvator-xs.dts
arch/arm64/boot/dts/renesas/r8a77961-salvator-xs.dts
arch/arm64/boot/dts/renesas/r8a77965-salvator-xs.dts
arch/arm64/boot/dts/renesas/salvator-xs.dtsi

I think I've added the relevant entries to my dtb, but I haven't
successfully captured audio yet.

I can see the device being listed through arecord:

kbingham@salvator-xs:~$ arecord -l
**** List of CAPTURE Hardware Devices ****
card 0: rcarsound [rcar-sound], device 0: rsnd-dai.0-ak4613-hifi
ak4613-hifi-0 []
  Subdevices: 0/1
  Subdevice #0: subdevice #0
card 0: rcarsound [rcar-sound], device 3: rsnd-dai.3-adv748x-i2s
adv748x.4-0070-3 []
  Subdevices: 1/1
  Subdevice #0: subdevice #0


But as yet, everything I try to record fails or is empty silence.

Debugging ...

--
Regards

Kieran



>>  3 files changed, 45 insertions(+), 6 deletions(-)
>>
>> diff --git a/arch/arm64/boot/dts/renesas/r8a77950-salvator-x.dts b/arch/arm64/boot/dts/renesas/r8a77950-salvator-x.dts
>> index 2438825c9b22..e16c146808b6 100644
>> --- a/arch/arm64/boot/dts/renesas/r8a77950-salvator-x.dts
>> +++ b/arch/arm64/boot/dts/renesas/r8a77950-salvator-x.dts
>> @@ -146,7 +146,8 @@ &sata {
>>  &sound_card {
>>  	dais = <&rsnd_port0	/* ak4613 */
>>  		&rsnd_port1	/* HDMI0  */
>> -		&rsnd_port2>;	/* HDMI1  */
>> +		&rsnd_port2	/* HDMI1  */
>> +		&rsnd_port3>;	/* adv7482 hdmi-in  */
> 
> Ah - that was confusing at first... but HDMI0 and HDMI1 are *outputs*,
> where of course the adv7482 is an input ;-)
> 
> 
> Otherwise, I can't spot anything else yet so:
> 
> Reviewed-by: Kieran Bingham <kieran.bingham+renesas@xxxxxxxxxxxxxxxx>
> 
> But I fear there may have been some churn around here, so it would be
> good to see a rebase too.
> 
> --
> Kieran
> 
> 
> 
>>  };
>>  
>>  &usb2_phy2 {
>> diff --git a/arch/arm64/boot/dts/renesas/r8a77961.dtsi b/arch/arm64/boot/dts/renesas/r8a77961.dtsi
>> index be3824bda632..b79907beaf31 100644
>> --- a/arch/arm64/boot/dts/renesas/r8a77961.dtsi
>> +++ b/arch/arm64/boot/dts/renesas/r8a77961.dtsi
>> @@ -861,6 +861,7 @@ rcar_sound,src {
>>  			rcar_sound,ssi {
>>  				ssi0: ssi-0 { };
>>  				ssi1: ssi-1 { };
>> +				ssi4: ssi-4 { };
>>  			};
>>  		};
>>  
>> diff --git a/arch/arm64/boot/dts/renesas/salvator-common.dtsi b/arch/arm64/boot/dts/renesas/salvator-common.dtsi
>> index 98bbcafc8c0d..ead7f8d7a929 100644
>> --- a/arch/arm64/boot/dts/renesas/salvator-common.dtsi
>> +++ b/arch/arm64/boot/dts/renesas/salvator-common.dtsi
>> @@ -460,7 +460,7 @@ pca9654: gpio@20 {
>>  		#gpio-cells = <2>;
>>  	};
>>  
>> -	video-receiver@70 {
>> +	adv7482_hdmi_in: video-receiver@70 {
>>  		compatible = "adi,adv7482";
>>  		reg = <0x70 0x71 0x72 0x73 0x74 0x75
>>  		       0x60 0x61 0x62 0x63 0x64 0x65>;
>> @@ -469,6 +469,7 @@ video-receiver@70 {
>>  
>>  		#address-cells = <1>;
>>  		#size-cells = <0>;
>> +		#clock-cells = <0>; /* the MCLK for I2S output */
>>  
>>  		interrupt-parent = <&gpio6>;
>>  		interrupt-names = "intrq1", "intrq2";
>> @@ -510,6 +511,15 @@ adv7482_txb: endpoint {
>>  				remote-endpoint = <&csi20_in>;
>>  			};
>>  		};
>> +
>> +		port@c {
>> +			reg = <12>;
>> +
>> +			adv7482_i2s: endpoint {
>> +				remote-endpoint = <&rsnd_endpoint3>;
>> +				system-clock-direction-out;
>> +			};
>> +		};
>>  	};
>>  
>>  	csa_vdd: adc@7c {
>> @@ -684,7 +694,8 @@ sdhi3_pins_uhs: sd3_uhs {
>>  	};
>>  
>>  	sound_pins: sound {
>> -		groups = "ssi01239_ctrl", "ssi0_data", "ssi1_data_a";
>> +		groups = "ssi01239_ctrl", "ssi0_data", "ssi1_data_a",
>> +			 "ssi4_data", "ssi4_ctrl";
>>  		function = "ssi";
>>  	};
>>  
>> @@ -733,8 +744,8 @@ &rcar_sound {
>>  	pinctrl-0 = <&sound_pins &sound_clk_pins>;
>>  	pinctrl-names = "default";
>>  
>> -	/* Single DAI */
>> -	#sound-dai-cells = <0>;
>> +	/* multi DAI */
>> +	#sound-dai-cells = <1>;
>>  
>>  	/* audio_clkout0/1/2/3 */
>>  	#clock-cells = <1>;
>> @@ -758,8 +769,19 @@ &rcar_sound {
>>  		 <&cpg CPG_MOD 1020>, <&cpg CPG_MOD 1021>,
>>  		 <&cpg CPG_MOD 1019>, <&cpg CPG_MOD 1018>,
>>  		 <&audio_clk_a>, <&cs2000>,
>> -		 <&audio_clk_c>,
>> +		 <&adv7482_hdmi_in>,
>>  		 <&cpg CPG_CORE CPG_AUDIO_CLK_I>;
>> +	clock-names = "ssi-all",
>> +		      "ssi.9", "ssi.8", "ssi.7", "ssi.6",
>> +		      "ssi.5", "ssi.4", "ssi.3", "ssi.2",
>> +		      "ssi.1", "ssi.0",
>> +		      "src.9", "src.8", "src.7", "src.6",
>> +		      "src.5", "src.4", "src.3", "src.2",
>> +		      "src.1", "src.0",
>> +		      "mix.1", "mix.0",
>> +		      "ctu.1", "ctu.0",
>> +		      "dvc.0", "dvc.1",
>> +		      "clk_a", "clk_b", "clk_c", "clk_i";
>>  
>>  	ports {
>>  		#address-cells = <1>;
>> @@ -777,6 +799,21 @@ rsnd_endpoint0: endpoint {
>>  				capture  = <&ssi1 &src1 &dvc1>;
>>  			};
>>  		};
>> +		rsnd_port3: port@3 {
>> +			reg = <3>;
>> +			rsnd_endpoint3: endpoint {
>> +				remote-endpoint = <&adv7482_i2s>;
>> +
>> +				dai-tdm-slot-num = <8>;
>> +				dai-tdm-slot-width = <32>;
>> +				dai-format = "left_j";
>> +				mclk-fs = <256>;
>> +				bitclock-master = <&adv7482_i2s>;
>> +				frame-master = <&adv7482_i2s>;
>> +
>> +				capture = <&ssi4>;
>> +			};
>> +		};
>>  	};
>>  };
>>  
>>
> 

-- 
Regards
--
Kieran



[Index of Archives]     [Device Tree Compilter]     [Device Tree Spec]     [Linux Driver Backports]     [Video for Linux]     [Linux USB Devel]     [Linux PCI Devel]     [Linux Audio Users]     [Linux Kernel]     [Linux SCSI]     [XFree86]     [Yosemite Backpacking]


  Powered by Linux