Em Tue, 11 Aug 2020 14:21:06 +0200
Mauro Carvalho Chehab <mchehab+huawei@xxxxxxxxxx> escreveu:
> I was able to drop it, but I had to add this at dwc3 settings:
>
> regulator-on-in-suspend;
>
> As otherwise the device seems to stop a few seconds after the dwc3
> driver gets started.
>
> I suspect it could be related to those calls at the dwg3 driver:
>
> pm_runtime_use_autosuspend(dev);
> pm_runtime_set_autosuspend_delay(dev, DWC3_DEFAULT_AUTOSUSPEND_DELAY);
>
> As this seems to be the only difference between what the dwc3 core
> does and the dwc3-hisi doesn't do.
Found the issue.
It is due to a quirk that was renamed:
- snps,dis-split-quirk;
+ snps,dis_enblslpm_quirk;
I'm now using just those drivers:
- hikey 970 phy (pulled from OOT);
- upstream dwc3;
- upstream rt1711 driver;
- drivers/misc/hisi_hikey_usb.c (with my changes).
Now, the problem is that the USB devices are getting one reset per
second (which starts about 10 seconds after dwc3 driver is loaded):
[ 14.080666] usb 1-1.1: reset low-speed USB device number 3 using xhci-hcd
[ 14.752689] usb 1-1.2: reset low-speed USB device number 4 using xhci-hcd
[ 15.712646] usb 1-1.1: reset low-speed USB device number 3 using xhci-hcd
[ 16.480683] usb 1-1.2: reset low-speed USB device number 4 using xhci-hcd
[ 17.472651] usb 1-1.1: reset low-speed USB device number 3 using xhci-hcd
[ 18.208675] usb 1-1.2: reset low-speed USB device number 4 using xhci-hcd
It sounds like an autosuspend thing, but disabling it (using powertop)
doesn't affect it. Any ideas?
PS.: I'm enclosing the relevant DT data.
Thanks,
Mauro
i2c1: i2c@ffd72000 {
compatible = "snps,designware-i2c";
reg = <0x0 0xffd72000 0x0 0x1000>;
interrupts = <GIC_SPI 119 IRQ_TYPE_LEVEL_HIGH>;
#address-cells = <1>;
#size-cells = <0>;
clock-frequency = <400000>;
clocks = <&iomcu HI3670_CLK_GATE_I2C1>;
resets = <&iomcu_rst 0x20 4>;
pinctrl-names = "default";
pinctrl-0 = <&i2c1_pmx_func &i2c1_cfg_func>;
rt1711h: rt1711h@4e {
compatible = "richtek,rt1711h";
reg = <0x4e>;
status = "ok";
interrupt-parent = <&gpio27>;
interrupts = <5 IRQ_TYPE_LEVEL_LOW>;
pinctrl-names = "default";
pinctrl-0 = <&pd_cfg_func>;
usb_con: connector {
compatible = "usb-c-connector";
label = "USB-C";
data-role = "dual";
power-role = "dual";
try-power-role = "sink";
source-pdos = <PDO_FIXED(5000, 500, PDO_FIXED_USB_COMM)>;
sink-pdos = <PDO_FIXED(5000, 500, PDO_FIXED_USB_COMM)
PDO_VAR(5000, 5000, 1000)>;
op-sink-microwatt = <10000000>;
ports {
#address-cells = <1>;
#size-cells = <0>;
port@1 {
reg = <1>;
usb_con_ss: endpoint {
remote-endpoint = <&dwc3_ss>;
};
};
};
};
port {
#address-cells = <1>;
#size-cells = <0>;
rt1711h_ep: endpoint@0 {
reg = <0>;
remote-endpoint = <&hikey_usb_ep1>;
};
};
};
};
hikey_usbhub: hikey_usbhub {
compatible = "hisilicon,kirin970_hikey_usbhub";
typec-vbus-gpios = <&gpio26 1 0>;
otg-switch-gpios = <&gpio4 2 0>;
hub_reset_en_gpio = <&gpio0 3 0>;
hub-vdd-supply = <&ldo17>;
usb-role-switch;
port {
#address-cells = <1>;
#size-cells = <0>;
hikey_usb_ep0: endpoint@0 {
reg = <0>;
remote-endpoint = <&dwc3_role_switch>;
};
hikey_usb_ep1: endpoint@1 {
reg = <1>;
remote-endpoint = <&rt1711h_ep>;
};
};
};
usb31_misc: usb31_misc@ff200000 {
compatible = "syscon";
reg = <0x0 0xff200000 0x0 0x1000>;
};
usb31_misc_rst: usb31_misc_rst_controller {
compatible = "hisilicon,hi3660-reset";
#reset-cells = <2>;
hisi,rst-syscon = <&usb31_misc>;
};
usb_phy: usbphy {
compatible = "hisilicon,hi3670-usb-phy";
#phy-cells = <0>;
hisilicon,pericrg-syscon = <&crg_ctrl>;
hisilicon,pctrl-syscon = <&pctrl>;
hisilicon,sctrl-syscon = <&sctrl>;
hisilicon,usb31-misc-syscon = <&usb31_misc>;
eye-diagram-param = <0xFDFEE4>;
usb3-phy-tx-vboost-lvl = <0x5>;
};
dwc3: dwc3@ff100000 {
compatible = "snps,dwc3";
reg = <0x0 0xff100000 0x0 0x100000>;
interrupts = <0 159 IRQ_TYPE_LEVEL_HIGH>,
<0 161 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&crg_ctrl HI3670_CLK_GATE_ABB_USB>,
<&crg_ctrl HI3670_HCLK_GATE_USB3OTG>,
<&crg_ctrl HI3670_CLK_GATE_USB3OTG_REF>,
<&crg_ctrl HI3670_ACLK_GATE_USB3DVFS>;
clock-names = "clk_gate_abb_usb",
"hclk_gate_usb3otg",
"clk_gate_usb3otg_ref",
"aclk_gate_usb3dvfs";
assigned-clocks = <&crg_ctrl HI3670_ACLK_GATE_USB3DVFS>;
assigned-clock-rates = <238000000>;
resets = <&crg_rst 0x90 6>,
<&crg_rst 0x90 7>,
<&usb31_misc_rst 0xA0 8>,
<&usb31_misc_rst 0xA0 9>;
phys = <&usb_phy>;
phy-names = "usb3-phy";
dr_mode = "otg";
maximum-speed = "super-speed";
phy_type = "utmi";
snps,dis-del-phy-power-chg-quirk;
snps,lfps_filter_quirk;
snps,dis_u2_susphy_quirk;
snps,dis_u3_susphy_quirk;
snps,tx_de_emphasis_quirk;
snps,tx_de_emphasis = <1>;
snps,dis_enblslpm_quirk;
snps,gctl-reset-quirk;
usb-role-switch;
role-switch-default-mode = "host";
port {
#address-cells = <1>;
#size-cells = <0>;
dwc3_role_switch: endpoint@0 {
reg = <0>;
remote-endpoint = <&hikey_usb_ep0>;
};
dwc3_ss: endpoint@1 {
reg = <1>;
remote-endpoint = <&usb_con_ss>;
};
};
};
