On 8/5/20 7:19 AM, Dmitry Osipenko wrote:
05.08.2020 17:05, Dmitry Osipenko пишет:
05.08.2020 16:46, Thierry Reding пишет:
On Mon, Aug 03, 2020 at 08:42:24AM -0700, Sowjanya Komatineni wrote:
With the split of MIPI calibration into tegra_mipi_calibrate() and
tegra_mipi_wait(), MIPI clock is not kept enabled till the calibration
is done.
So, this patch skips disabling MIPI clock after triggering start of
calibration and disables it only after waiting for done status from
the calibration logic.
This patch renames tegra_mipi_calibrate() as tegra_mipi_start_calibration()
and tegra_mipi_wait() as tegra_mipi_finish_calibration() to be inline
with their usage.
As MIPI clock is left enabled and in case of any failures with CSI input
streaming tegra_mipi_finish_calibration() will not get invoked.
So added new API tegra_mipi_cancel_calibration() which disables MIPI clock
and consumer drivers can call this in such cases.
Reviewed-by: Dmitry Osipenko <digetx@xxxxxxxxx>
Signed-off-by: Sowjanya Komatineni <skomatineni@xxxxxxxxxx>
---
drivers/gpu/drm/tegra/dsi.c | 4 ++--
drivers/gpu/host1x/mipi.c | 19 ++++++++++---------
include/linux/host1x.h | 5 +++--
3 files changed, 15 insertions(+), 13 deletions(-)
diff --git a/drivers/gpu/drm/tegra/dsi.c b/drivers/gpu/drm/tegra/dsi.c
index 3820e8d..a7864e9 100644
--- a/drivers/gpu/drm/tegra/dsi.c
+++ b/drivers/gpu/drm/tegra/dsi.c
@@ -694,11 +694,11 @@ static int tegra_dsi_pad_calibrate(struct tegra_dsi *dsi)
DSI_PAD_PREEMP_PD(0x03) | DSI_PAD_PREEMP_PU(0x3);
tegra_dsi_writel(dsi, value, DSI_PAD_CONTROL_3);
- err = tegra_mipi_calibrate(dsi->mipi);
+ err = tegra_mipi_start_calibration(dsi->mipi);
if (err < 0)
return err;
- return tegra_mipi_wait(dsi->mipi);
+ return tegra_mipi_finish_calibration(dsi->mipi);
}
static void tegra_dsi_set_timeout(struct tegra_dsi *dsi, unsigned long bclk,
diff --git a/drivers/gpu/host1x/mipi.c b/drivers/gpu/host1x/mipi.c
index e606464..b15ab6e 100644
--- a/drivers/gpu/host1x/mipi.c
+++ b/drivers/gpu/host1x/mipi.c
@@ -293,17 +293,19 @@ int tegra_mipi_disable(struct tegra_mipi_device *dev)
}
EXPORT_SYMBOL(tegra_mipi_disable);
-int tegra_mipi_wait(struct tegra_mipi_device *device)
+void tegra_mipi_cancel_calibration(struct tegra_mipi_device *device)
+{
+ clk_disable(device->mipi->clk);
Do we need to do anything with the MIPI_CAL_CTRL and MIPI_CAL_STATUS
registers here? We don't clear the START bit in the former when the
calibration has successfully finished, but I suspect that's because
the bit is self-clearing. But I wonder if we still need to clear it
upon cancellation to make sure the calibration does indeed stop.
Apparently there is no way to explicitly stop calibration other than to
reset MIPI calibration block, but Sowjanya says this is unnecessary.
Perhaps having a fixed delay before disabling clock could be enough to
ensure that calibration is stopped before the clock is disabled?
Actually, there is a MIPI_CAL_ACTIVE bit in the status register. Maybe
it needs to be polled until it's unset?
Confirmed with HW design team during this patch update.
SW does not need to clear START bit and only write 1 takes effect to
that bit.
Also, no need to have delay or do any other register settings unclear as
its FSM and there's nothing to get stuck.
Also it goes thru small finite set of codes and by the time sensor
programming happens for enabling streaming FSM will finish its
calibration sequence much early and it will only wait for pads LP-11.
So, during cancel we only need disable MIPI clock.
