In order to automate the verification of DT nodes convert ti,sci-intr.txt ti,sci-intr.yaml. Signed-off-by: Lokesh Vutla <lokeshvutla@xxxxxx> --- .../interrupt-controller/ti,sci-intr.txt | 83 -------------- .../interrupt-controller/ti,sci-intr.yaml | 102 ++++++++++++++++++ MAINTAINERS | 2 +- 3 files changed, 103 insertions(+), 84 deletions(-) delete mode 100644 Documentation/devicetree/bindings/interrupt-controller/ti,sci-intr.txt create mode 100644 Documentation/devicetree/bindings/interrupt-controller/ti,sci-intr.yaml diff --git a/Documentation/devicetree/bindings/interrupt-controller/ti,sci-intr.txt b/Documentation/devicetree/bindings/interrupt-controller/ti,sci-intr.txt deleted file mode 100644 index 8b56b2de1c73..000000000000 --- a/Documentation/devicetree/bindings/interrupt-controller/ti,sci-intr.txt +++ /dev/null @@ -1,83 +0,0 @@ -Texas Instruments K3 Interrupt Router -===================================== - -The Interrupt Router (INTR) module provides a mechanism to mux M -interrupt inputs to N interrupt outputs, where all M inputs are selectable -to be driven per N output. An Interrupt Router can either handle edge triggered -or level triggered interrupts and that is fixed in hardware. - - Interrupt Router - +----------------------+ - | Inputs Outputs | - +-------+ | +------+ +-----+ | - | GPIO |----------->| | irq0 | | 0 | | Host IRQ - +-------+ | +------+ +-----+ | controller - | . . | +-------+ - +-------+ | . . |----->| IRQ | - | INTA |----------->| . . | +-------+ - +-------+ | . +-----+ | - | +------+ | N | | - | | irqM | +-----+ | - | +------+ | - | | - +----------------------+ - -There is one register per output (MUXCNTL_N) that controls the selection. -Configuration of these MUXCNTL_N registers is done by a system controller -(like the Device Memory and Security Controller on K3 AM654 SoC). System -controller will keep track of the used and unused registers within the Router. -Driver should request the system controller to get the range of GIC IRQs -assigned to the requesting hosts. It is the drivers responsibility to keep -track of Host IRQs. - -Communication between the host processor running an OS and the system -controller happens through a protocol called TI System Control Interface -(TISCI protocol). For more details refer: -Documentation/devicetree/bindings/arm/keystone/ti,sci.txt - -TISCI Interrupt Router Node: ----------------------------- -Required Properties: -- compatible: Must be "ti,sci-intr". -- ti,intr-trigger-type: Should be one of the following: - 1: If intr supports edge triggered interrupts. - 4: If intr supports level triggered interrupts. -- interrupt-controller: Identifies the node as an interrupt controller -- #interrupt-cells: Specifies the number of cells needed to encode an - interrupt source. The value should be 1. - First cell should contain interrupt router input number - as specified by hardware. -- ti,sci: Phandle to TI-SCI compatible System controller node. -- ti,sci-dev-id: TISCI device id of interrupt controller. -- ti,interrupt-ranges: Set of triplets containing ranges that convert - the INTR output interrupt numbers to parent's - interrupt number. Each triplet has following entries: - - First entry specifies the base for intr output irq - - Second entry specifies the base for parent irqs - - Third entry specifies the limit - -For more details on TISCI IRQ resource management refer: -http://downloads.ti.com/tisci/esd/latest/2_tisci_msgs/rm/rm_irq.html - -Example: --------- -The following example demonstrates both interrupt router node and the consumer -node(main gpio) on the AM654 SoC: - -main_gpio_intr: interrupt-controller0 { - compatible = "ti,sci-intr"; - ti,intr-trigger-type = <1>; - interrupt-controller; - interrupt-parent = <&gic500>; - #interrupt-cells = <1>; - ti,sci = <&dmsc>; - ti,sci-dev-id = <131>; - ti,interrupt-ranges = <0 360 32>; -}; - -main_gpio0: gpio@600000 { - ... - interrupt-parent = <&main_gpio_intr>; - interrupts = <192>, <193>, <194>, <195>, <196>, <197>; - ... -}; diff --git a/Documentation/devicetree/bindings/interrupt-controller/ti,sci-intr.yaml b/Documentation/devicetree/bindings/interrupt-controller/ti,sci-intr.yaml new file mode 100644 index 000000000000..f7a3e51a5212 --- /dev/null +++ b/Documentation/devicetree/bindings/interrupt-controller/ti,sci-intr.yaml @@ -0,0 +1,102 @@ +# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/interrupt-controller/ti,sci-intr.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Texas Instruments K3 Interrupt Router + +maintainers: + - Lokesh Vutla <lokeshvutla@xxxxxx> + +allOf: + - $ref: /schemas/arm/keystone/ti,k3-sci-common.yaml# + +description: | + The Interrupt Router (INTR) module provides a mechanism to mux M + interrupt inputs to N interrupt outputs, where all M inputs are selectable + to be driven per N output. An Interrupt Router can either handle edge + triggered or level triggered interrupts and that is fixed in hardware. + + Interrupt Router + +----------------------+ + | Inputs Outputs | + +-------+ | +------+ +-----+ | + | GPIO |----------->| | irq0 | | 0 | | Host IRQ + +-------+ | +------+ +-----+ | controller + | . . | +-------+ + +-------+ | . . |----->| IRQ | + | INTA |----------->| . . | +-------+ + +-------+ | . +-----+ | + | +------+ | N | | + | | irqM | +-----+ | + | +------+ | + | | + +----------------------+ + + There is one register per output (MUXCNTL_N) that controls the selection. + Configuration of these MUXCNTL_N registers is done by a system controller + (like the Device Memory and Security Controller on K3 AM654 SoC). System + controller will keep track of the used and unused registers within the Router. + Driver should request the system controller to get the range of GIC IRQs + assigned to the requesting hosts. It is the drivers responsibility to keep + track of Host IRQs. + + Communication between the host processor running an OS and the system + controller happens through a protocol called TI System Control Interface + (TISCI protocol). + +properties: + compatible: + const: ti,sci-intr + + ti,intr-trigger-type: + $ref: /schemas/types.yaml#/definitions/uint32 + enum: [1, 4] + description: | + Should be one of the following. + 1 = If intr supports edge triggered interrupts. + 4 = If intr supports level triggered interrupts. + + interrupt-controller: true + + '#interrupt-cells': + const: 1 + description: | + The 1st cell should contain interrupt router input hw number. + + ti,interrupt-ranges: + $ref: /schemas/types.yaml#/definitions/uint32-matrix + description: | + Interrupt ranges that converts the INTR output hw irq numbers + to parents's input interrupt numbers. + - items: + items: + - description: | + "output_irq" specifies the base for intr output irq + - description: | + "parent's input irq" specifies the base for parent irq + - description: | + "limit" specifies the limit for translation + +required: + - compatible + - ti,intr-trigger-type + - interrupt-controller + - '#interrupt-cells' + - ti,sci + - ti,sci-dev-id + - ti,interrupt-ranges + +examples: + - | + main_gpio_intr: interrupt-controller0 { + compatible = "ti,sci-intr"; + ti,intr-trigger-type = <1>; + interrupt-controller; + interrupt-parent = <&gic500>; + #interrupt-cells = <1>; + ti,sci = <&dmsc>; + ti,sci-dev-id = <131>; + ti,interrupt-ranges = <0 360 32>; + }; diff --git a/MAINTAINERS b/MAINTAINERS index c76fd456aaba..bc88886c05c6 100644 --- a/MAINTAINERS +++ b/MAINTAINERS @@ -16919,7 +16919,7 @@ F: Documentation/devicetree/bindings/arm/keystone/ti,k3-sci-common.yaml F: Documentation/devicetree/bindings/arm/keystone/ti,sci.txt F: Documentation/devicetree/bindings/clock/ti,sci-clk.txt F: Documentation/devicetree/bindings/interrupt-controller/ti,sci-inta.txt -F: Documentation/devicetree/bindings/interrupt-controller/ti,sci-intr.txt +F: Documentation/devicetree/bindings/interrupt-controller/ti,sci-intr.yaml F: Documentation/devicetree/bindings/reset/ti,sci-reset.txt F: Documentation/devicetree/bindings/soc/ti/sci-pm-domain.txt F: drivers/clk/keystone/sci-clk.c -- 2.27.0
