Add support for Seeed Studio's stm32mp157c odyssey board.
Board consists of SoM with stm32mp157c with 4GB eMMC and 512 MB DDR3 RAM
and carrier board with USB and ETH interfaces, SD card connector,
wifi and BT chip AP6236.
In this patch only basic kernel boot is supported and interfacing
SD card and on-board eMMC.
Signed-off-by: Marcin Sloniewski <marcin.sloniewski@xxxxxxxxx>
---
Changes in v2:
- add new odyssey dts to Makefile
arch/arm/boot/dts/Makefile | 3 +-
.../arm/boot/dts/stm32mp157c-odyssey-som.dtsi | 276 ++++++++++++++++++
arch/arm/boot/dts/stm32mp157c-odyssey.dts | 72 +++++
3 files changed, 350 insertions(+), 1 deletion(-)
create mode 100644 arch/arm/boot/dts/stm32mp157c-odyssey-som.dtsi
create mode 100644 arch/arm/boot/dts/stm32mp157c-odyssey.dts
diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
index e6a1cac0bfc7..a3ea2301c82c 100644
--- a/arch/arm/boot/dts/Makefile
+++ b/arch/arm/boot/dts/Makefile
@@ -1047,7 +1047,8 @@ dtb-$(CONFIG_ARCH_STM32) += \
stm32mp157c-dk2.dtb \
stm32mp157c-ed1.dtb \
stm32mp157c-ev1.dtb \
- stm32mp157c-lxa-mc1.dtb
+ stm32mp157c-lxa-mc1.dtb \
+ stm32mp157c-odyssey.dtb
dtb-$(CONFIG_MACH_SUN4I) += \
sun4i-a10-a1000.dtb \
sun4i-a10-ba10-tvbox.dtb \
diff --git a/arch/arm/boot/dts/stm32mp157c-odyssey-som.dtsi b/arch/arm/boot/dts/stm32mp157c-odyssey-som.dtsi
new file mode 100644
index 000000000000..620ff9e7f370
--- /dev/null
+++ b/arch/arm/boot/dts/stm32mp157c-odyssey-som.dtsi
@@ -0,0 +1,276 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR BSD-3-Clause)
+/*
+ * Copyright (C) 2020 Marcin Sloniewski <marcin.sloniewski@xxxxxxxxx>.
+ */
+
+/dts-v1/;
+
+#include "stm32mp157.dtsi"
+#include "stm32mp15xc.dtsi"
+#include "stm32mp15-pinctrl.dtsi"
+#include "stm32mp15xxac-pinctrl.dtsi"
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/mfd/st,stpmic1.h>
+
+/ {
+ model = "Seeed Studio Odyssey-STM32MP157C SOM";
+ compatible = "seeed,stm32mp157c-odyssey-som", "st,stm32mp157";
+
+ memory@c0000000 {
+ reg = <0xc0000000 0x20000000>;
+ };
+
+ reserved-memory {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges;
+
+ mcuram2: mcuram2@10000000 {
+ compatible = "shared-dma-pool";
+ reg = <0x10000000 0x40000>;
+ no-map;
+ };
+
+ vdev0vring0: vdev0vring0@10040000 {
+ compatible = "shared-dma-pool";
+ reg = <0x10040000 0x1000>;
+ no-map;
+ };
+
+ vdev0vring1: vdev0vring1@10041000 {
+ compatible = "shared-dma-pool";
+ reg = <0x10041000 0x1000>;
+ no-map;
+ };
+
+ vdev0buffer: vdev0buffer@10042000 {
+ compatible = "shared-dma-pool";
+ reg = <0x10042000 0x4000>;
+ no-map;
+ };
+
+ mcuram: mcuram@30000000 {
+ compatible = "shared-dma-pool";
+ reg = <0x30000000 0x40000>;
+ no-map;
+ };
+
+ retram: retram@38000000 {
+ compatible = "shared-dma-pool";
+ reg = <0x38000000 0x10000>;
+ no-map;
+ };
+
+ gpu_reserved: gpu@d4000000 {
+ reg = <0xd4000000 0x4000000>;
+ no-map;
+ };
+ };
+
+ led {
+ compatible = "gpio-leds";
+ blue {
+ label = "heartbeat";
+ gpios = <&gpiog 3 GPIO_ACTIVE_HIGH>;
+ linux,default-trigger = "heartbeat";
+ default-state = "off";
+ };
+ };
+};
+
+&gpu {
+ contiguous-area = <&gpu_reserved>;
+ status = "okay";
+};
+
+&i2c2 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c2_pins_a>;
+ i2c-scl-rising-time-ns = <185>;
+ i2c-scl-falling-time-ns = <20>;
+ status = "okay";
+ /* spare dmas for other usage */
+ /delete-property/dmas;
+ /delete-property/dma-names;
+
+ pmic: stpmic@33 {
+ compatible = "st,stpmic1";
+ reg = <0x33>;
+ interrupts-extended = <&gpioa 0 IRQ_TYPE_EDGE_FALLING>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ status = "okay";
+
+ regulators {
+ compatible = "st,stpmic1-regulators";
+ ldo1-supply = <&v3v3>;
+ ldo3-supply = <&vdd_ddr>;
+ ldo6-supply = <&v3v3>;
+ pwr_sw1-supply = <&bst_out>;
+ pwr_sw2-supply = <&bst_out>;
+
+ vddcore: buck1 {
+ regulator-name = "vddcore";
+ regulator-min-microvolt = <800000>;
+ regulator-max-microvolt = <1350000>;
+ regulator-always-on;
+ regulator-initial-mode = <0>;
+ regulator-over-current-protection;
+ };
+
+ vdd_ddr: buck2 {
+ regulator-name = "vdd_ddr";
+ regulator-min-microvolt = <1350000>;
+ regulator-max-microvolt = <1350000>;
+ regulator-always-on;
+ regulator-initial-mode = <0>;
+ regulator-over-current-protection;
+ };
+
+ vdd: buck3 {
+ regulator-name = "vdd";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-always-on;
+ st,mask-reset;
+ regulator-initial-mode = <0>;
+ regulator-over-current-protection;
+ };
+
+ v3v3: buck4 {
+ regulator-name = "v3v3";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-always-on;
+ regulator-over-current-protection;
+ regulator-initial-mode = <0>;
+ };
+
+ v1v8_audio: ldo1 {
+ regulator-name = "v1v8_audio";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-always-on;
+ interrupts = <IT_CURLIM_LDO1 0>;
+ };
+
+ v3v3_hdmi: ldo2 {
+ regulator-name = "v3v3_hdmi";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-always-on;
+ interrupts = <IT_CURLIM_LDO2 0>;
+ };
+
+ vtt_ddr: ldo3 {
+ regulator-name = "vtt_ddr";
+ regulator-min-microvolt = <500000>;
+ regulator-max-microvolt = <750000>;
+ regulator-always-on;
+ regulator-over-current-protection;
+ };
+
+ vdd_usb: ldo4 {
+ regulator-name = "vdd_usb";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ interrupts = <IT_CURLIM_LDO4 0>;
+ };
+
+ vdda: ldo5 {
+ regulator-name = "vdda";
+ regulator-min-microvolt = <2900000>;
+ regulator-max-microvolt = <2900000>;
+ interrupts = <IT_CURLIM_LDO5 0>;
+ regulator-boot-on;
+ };
+
+ v1v2_hdmi: ldo6 {
+ regulator-name = "v1v2_hdmi";
+ regulator-min-microvolt = <1200000>;
+ regulator-max-microvolt = <1200000>;
+ regulator-always-on;
+ interrupts = <IT_CURLIM_LDO6 0>;
+ };
+
+ vref_ddr: vref_ddr {
+ regulator-name = "vref_ddr";
+ regulator-always-on;
+ regulator-over-current-protection;
+ };
+
+ bst_out: boost {
+ regulator-name = "bst_out";
+ interrupts = <IT_OCP_BOOST 0>;
+ };
+
+ vbus_otg: pwr_sw1 {
+ regulator-name = "vbus_otg";
+ interrupts = <IT_OCP_OTG 0>;
+ };
+
+ vbus_sw: pwr_sw2 {
+ regulator-name = "vbus_sw";
+ interrupts = <IT_OCP_SWOUT 0>;
+ regulator-active-discharge;
+ };
+ };
+
+ onkey {
+ compatible = "st,stpmic1-onkey";
+ interrupts = <IT_PONKEY_F 0>, <IT_PONKEY_R 0>;
+ interrupt-names = "onkey-falling", "onkey-rising";
+ power-off-time-sec = <10>;
+ status = "okay";
+ };
+
+ watchdog {
+ compatible = "st,stpmic1-wdt";
+ status = "disabled";
+ };
+ };
+};
+
+&ipcc {
+ status = "okay";
+};
+
+&iwdg2 {
+ timeout-sec = <32>;
+ status = "okay";
+};
+
+&m4_rproc {
+ memory-region = <&retram>, <&mcuram>, <&mcuram2>, <&vdev0vring0>,
+ <&vdev0vring1>, <&vdev0buffer>;
+ mboxes = <&ipcc 0>, <&ipcc 1>, <&ipcc 2>;
+ mbox-names = "vq0", "vq1", "shutdown";
+ interrupt-parent = <&exti>;
+ interrupts = <68 1>;
+ status = "okay";
+};
+
+&rng1 {
+ status = "okay";
+};
+
+&rtc {
+ status = "okay";
+};
+
+&sdmmc2 {
+ pinctrl-names = "default", "opendrain", "sleep";
+ pinctrl-0 = <&sdmmc2_b4_pins_a &sdmmc2_d47_pins_a>;
+ pinctrl-1 = <&sdmmc2_b4_od_pins_a &sdmmc2_d47_pins_a>;
+ pinctrl-2 = <&sdmmc2_b4_sleep_pins_a &sdmmc2_d47_sleep_pins_a>;
+ non-removable;
+ no-sd;
+ no-sdio;
+ st,neg-edge;
+ bus-width = <4>;
+ vmmc-supply = <&v3v3>;
+ vqmmc-supply = <&v3v3>;
+ mmc-ddr-3_3v;
+ status = "okay";
+};
+
diff --git a/arch/arm/boot/dts/stm32mp157c-odyssey.dts b/arch/arm/boot/dts/stm32mp157c-odyssey.dts
new file mode 100644
index 000000000000..6c1b091af14f
--- /dev/null
+++ b/arch/arm/boot/dts/stm32mp157c-odyssey.dts
@@ -0,0 +1,72 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR BSD-3-Clause)
+/*
+ * Copyright (C) 2020 Marcin Sloniewski <marcin.sloniewski@xxxxxxxxx>.
+ */
+
+/dts-v1/;
+
+#include "stm32mp157c-odyssey-som.dtsi"
+
+/ {
+ model = "Seeed Studio Odyssey-STM32MP157C Board";
+ compatible = "seeed,stm32mp157c-odyssey", "st,stm32mp157";
+
+ aliases {
+ ethernet0 = ðernet0;
+ serial0 = &uart4;
+ };
+
+ chosen {
+ stdout-path = "serial0:115200n8";
+ };
+};
+
+ðernet0 {
+ status = "okay";
+ pinctrl-0 = <ðernet0_rgmii_pins_a>;
+ pinctrl-1 = <ðernet0_rgmii_pins_sleep_a>;
+ pinctrl-names = "default", "sleep";
+ phy-mode = "rgmii-id";
+ max-speed = <1000>;
+ phy-handle = <&phy0>;
+
+ mdio0 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ compatible = "snps,dwmac-mdio";
+ phy0: ethernet-phy@0 {
+ reg = <0>;
+ };
+ };
+};
+
+&i2c1 {
+ pinctrl-names = "default", "sleep";
+ pinctrl-0 = <&i2c1_pins_a>;
+ pinctrl-1 = <&i2c1_pins_sleep_a>;
+ i2c-scl-rising-time-ns = <100>;
+ i2c-scl-falling-time-ns = <7>;
+ status = "okay";
+ /delete-property/dmas;
+ /delete-property/dma-names;
+};
+
+&sdmmc1 {
+ pinctrl-names = "default", "opendrain", "sleep";
+ pinctrl-0 = <&sdmmc1_b4_pins_a>;
+ pinctrl-1 = <&sdmmc1_b4_od_pins_a>;
+ pinctrl-2 = <&sdmmc1_b4_sleep_pins_a>;
+ cd-gpios = <&gpiob 7 (GPIO_ACTIVE_LOW | GPIO_PULL_UP)>;
+ disable-wp;
+ st,neg-edge;
+ bus-width = <4>;
+ vmmc-supply = <&v3v3>;
+ status = "okay";
+};
+
+&uart4 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart4_pins_a>;
+ status = "okay";
+};
+
--
2.27.0
