Hi Marcin,
On 7/6/20 7:33 PM, Marcin Sloniewski wrote:
Add support for Seeed Studio's stm32mp157c odyssey board.
Board consists of SoM with stm32mp157c with 4GB eMMC and 512 MB DDR3 RAM
and carrier board with USB and ETH interfaces, SD card connector,
wifi and BT chip AP6236.
In this patch only basic kernel boot is supported and interfacing
SD card and on-board eMMC.
Signed-off-by: Marcin Sloniewski <marcin.sloniewski@xxxxxxxxx>
Thanks for adding a new STM32MP157 board. Nothing to say about your DT
patchs except that Makefile update is missing.
regards
Alex
---
.../arm/boot/dts/stm32mp157c-odyssey-som.dtsi | 276 ++++++++++++++++++
arch/arm/boot/dts/stm32mp157c-odyssey.dts | 72 +++++
2 files changed, 348 insertions(+)
create mode 100644 arch/arm/boot/dts/stm32mp157c-odyssey-som.dtsi
create mode 100644 arch/arm/boot/dts/stm32mp157c-odyssey.dts
diff --git a/arch/arm/boot/dts/stm32mp157c-odyssey-som.dtsi b/arch/arm/boot/dts/stm32mp157c-odyssey-som.dtsi
new file mode 100644
index 000000000000..620ff9e7f370
--- /dev/null
+++ b/arch/arm/boot/dts/stm32mp157c-odyssey-som.dtsi
@@ -0,0 +1,276 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR BSD-3-Clause)
+/*
+ * Copyright (C) 2020 Marcin Sloniewski <marcin.sloniewski@xxxxxxxxx>.
+ */
+
+/dts-v1/;
+
+#include "stm32mp157.dtsi"
+#include "stm32mp15xc.dtsi"
+#include "stm32mp15-pinctrl.dtsi"
+#include "stm32mp15xxac-pinctrl.dtsi"
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/mfd/st,stpmic1.h>
+
+/ {
+ model = "Seeed Studio Odyssey-STM32MP157C SOM";
+ compatible = "seeed,stm32mp157c-odyssey-som", "st,stm32mp157";
+
+ memory@c0000000 {
+ reg = <0xc0000000 0x20000000>;
+ };
+
+ reserved-memory {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges;
+
+ mcuram2: mcuram2@10000000 {
+ compatible = "shared-dma-pool";
+ reg = <0x10000000 0x40000>;
+ no-map;
+ };
+
+ vdev0vring0: vdev0vring0@10040000 {
+ compatible = "shared-dma-pool";
+ reg = <0x10040000 0x1000>;
+ no-map;
+ };
+
+ vdev0vring1: vdev0vring1@10041000 {
+ compatible = "shared-dma-pool";
+ reg = <0x10041000 0x1000>;
+ no-map;
+ };
+
+ vdev0buffer: vdev0buffer@10042000 {
+ compatible = "shared-dma-pool";
+ reg = <0x10042000 0x4000>;
+ no-map;
+ };
+
+ mcuram: mcuram@30000000 {
+ compatible = "shared-dma-pool";
+ reg = <0x30000000 0x40000>;
+ no-map;
+ };
+
+ retram: retram@38000000 {
+ compatible = "shared-dma-pool";
+ reg = <0x38000000 0x10000>;
+ no-map;
+ };
+
+ gpu_reserved: gpu@d4000000 {
+ reg = <0xd4000000 0x4000000>;
+ no-map;
+ };
+ };
+
+ led {
+ compatible = "gpio-leds";
+ blue {
+ label = "heartbeat";
+ gpios = <&gpiog 3 GPIO_ACTIVE_HIGH>;
+ linux,default-trigger = "heartbeat";
+ default-state = "off";
+ };
+ };
+};
+
+&gpu {
+ contiguous-area = <&gpu_reserved>;
+ status = "okay";
+};
+
+&i2c2 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c2_pins_a>;
+ i2c-scl-rising-time-ns = <185>;
+ i2c-scl-falling-time-ns = <20>;
+ status = "okay";
+ /* spare dmas for other usage */
+ /delete-property/dmas;
+ /delete-property/dma-names;
+
+ pmic: stpmic@33 {
+ compatible = "st,stpmic1";
+ reg = <0x33>;
+ interrupts-extended = <&gpioa 0 IRQ_TYPE_EDGE_FALLING>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ status = "okay";
+
+ regulators {
+ compatible = "st,stpmic1-regulators";
+ ldo1-supply = <&v3v3>;
+ ldo3-supply = <&vdd_ddr>;
+ ldo6-supply = <&v3v3>;
+ pwr_sw1-supply = <&bst_out>;
+ pwr_sw2-supply = <&bst_out>;
+
+ vddcore: buck1 {
+ regulator-name = "vddcore";
+ regulator-min-microvolt = <800000>;
+ regulator-max-microvolt = <1350000>;
+ regulator-always-on;
+ regulator-initial-mode = <0>;
+ regulator-over-current-protection;
+ };
+
+ vdd_ddr: buck2 {
+ regulator-name = "vdd_ddr";
+ regulator-min-microvolt = <1350000>;
+ regulator-max-microvolt = <1350000>;
+ regulator-always-on;
+ regulator-initial-mode = <0>;
+ regulator-over-current-protection;
+ };
+
+ vdd: buck3 {
+ regulator-name = "vdd";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-always-on;
+ st,mask-reset;
+ regulator-initial-mode = <0>;
+ regulator-over-current-protection;
+ };
+
+ v3v3: buck4 {
+ regulator-name = "v3v3";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-always-on;
+ regulator-over-current-protection;
+ regulator-initial-mode = <0>;
+ };
+
+ v1v8_audio: ldo1 {
+ regulator-name = "v1v8_audio";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-always-on;
+ interrupts = <IT_CURLIM_LDO1 0>;
+ };
+
+ v3v3_hdmi: ldo2 {
+ regulator-name = "v3v3_hdmi";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-always-on;
+ interrupts = <IT_CURLIM_LDO2 0>;
+ };
+
+ vtt_ddr: ldo3 {
+ regulator-name = "vtt_ddr";
+ regulator-min-microvolt = <500000>;
+ regulator-max-microvolt = <750000>;
+ regulator-always-on;
+ regulator-over-current-protection;
+ };
+
+ vdd_usb: ldo4 {
+ regulator-name = "vdd_usb";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ interrupts = <IT_CURLIM_LDO4 0>;
+ };
+
+ vdda: ldo5 {
+ regulator-name = "vdda";
+ regulator-min-microvolt = <2900000>;
+ regulator-max-microvolt = <2900000>;
+ interrupts = <IT_CURLIM_LDO5 0>;
+ regulator-boot-on;
+ };
+
+ v1v2_hdmi: ldo6 {
+ regulator-name = "v1v2_hdmi";
+ regulator-min-microvolt = <1200000>;
+ regulator-max-microvolt = <1200000>;
+ regulator-always-on;
+ interrupts = <IT_CURLIM_LDO6 0>;
+ };
+
+ vref_ddr: vref_ddr {
+ regulator-name = "vref_ddr";
+ regulator-always-on;
+ regulator-over-current-protection;
+ };
+
+ bst_out: boost {
+ regulator-name = "bst_out";
+ interrupts = <IT_OCP_BOOST 0>;
+ };
+
+ vbus_otg: pwr_sw1 {
+ regulator-name = "vbus_otg";
+ interrupts = <IT_OCP_OTG 0>;
+ };
+
+ vbus_sw: pwr_sw2 {
+ regulator-name = "vbus_sw";
+ interrupts = <IT_OCP_SWOUT 0>;
+ regulator-active-discharge;
+ };
+ };
+
+ onkey {
+ compatible = "st,stpmic1-onkey";
+ interrupts = <IT_PONKEY_F 0>, <IT_PONKEY_R 0>;
+ interrupt-names = "onkey-falling", "onkey-rising";
+ power-off-time-sec = <10>;
+ status = "okay";
+ };
+
+ watchdog {
+ compatible = "st,stpmic1-wdt";
+ status = "disabled";
+ };
+ };
+};
+
+&ipcc {
+ status = "okay";
+};
+
+&iwdg2 {
+ timeout-sec = <32>;
+ status = "okay";
+};
+
+&m4_rproc {
+ memory-region = <&retram>, <&mcuram>, <&mcuram2>, <&vdev0vring0>,
+ <&vdev0vring1>, <&vdev0buffer>;
+ mboxes = <&ipcc 0>, <&ipcc 1>, <&ipcc 2>;
+ mbox-names = "vq0", "vq1", "shutdown";
+ interrupt-parent = <&exti>;
+ interrupts = <68 1>;
+ status = "okay";
+};
+
+&rng1 {
+ status = "okay";
+};
+
+&rtc {
+ status = "okay";
+};
+
+&sdmmc2 {
+ pinctrl-names = "default", "opendrain", "sleep";
+ pinctrl-0 = <&sdmmc2_b4_pins_a &sdmmc2_d47_pins_a>;
+ pinctrl-1 = <&sdmmc2_b4_od_pins_a &sdmmc2_d47_pins_a>;
+ pinctrl-2 = <&sdmmc2_b4_sleep_pins_a &sdmmc2_d47_sleep_pins_a>;
+ non-removable;
+ no-sd;
+ no-sdio;
+ st,neg-edge;
+ bus-width = <4>;
+ vmmc-supply = <&v3v3>;
+ vqmmc-supply = <&v3v3>;
+ mmc-ddr-3_3v;
+ status = "okay";
+};
+
diff --git a/arch/arm/boot/dts/stm32mp157c-odyssey.dts b/arch/arm/boot/dts/stm32mp157c-odyssey.dts
new file mode 100644
index 000000000000..6c1b091af14f
--- /dev/null
+++ b/arch/arm/boot/dts/stm32mp157c-odyssey.dts
@@ -0,0 +1,72 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR BSD-3-Clause)
+/*
+ * Copyright (C) 2020 Marcin Sloniewski <marcin.sloniewski@xxxxxxxxx>.
+ */
+
+/dts-v1/;
+
+#include "stm32mp157c-odyssey-som.dtsi"
+
+/ {
+ model = "Seeed Studio Odyssey-STM32MP157C Board";
+ compatible = "seeed,stm32mp157c-odyssey", "st,stm32mp157";
+
+ aliases {
+ ethernet0 = ðernet0;
+ serial0 = &uart4;
+ };
+
+ chosen {
+ stdout-path = "serial0:115200n8";
+ };
+};
+
+ðernet0 {
+ status = "okay";
+ pinctrl-0 = <ðernet0_rgmii_pins_a>;
+ pinctrl-1 = <ðernet0_rgmii_pins_sleep_a>;
+ pinctrl-names = "default", "sleep";
+ phy-mode = "rgmii-id";
+ max-speed = <1000>;
+ phy-handle = <&phy0>;
+
+ mdio0 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ compatible = "snps,dwmac-mdio";
+ phy0: ethernet-phy@0 {
+ reg = <0>;
+ };
+ };
+};
+
+&i2c1 {
+ pinctrl-names = "default", "sleep";
+ pinctrl-0 = <&i2c1_pins_a>;
+ pinctrl-1 = <&i2c1_pins_sleep_a>;
+ i2c-scl-rising-time-ns = <100>;
+ i2c-scl-falling-time-ns = <7>;
+ status = "okay";
+ /delete-property/dmas;
+ /delete-property/dma-names;
+};
+
+&sdmmc1 {
+ pinctrl-names = "default", "opendrain", "sleep";
+ pinctrl-0 = <&sdmmc1_b4_pins_a>;
+ pinctrl-1 = <&sdmmc1_b4_od_pins_a>;
+ pinctrl-2 = <&sdmmc1_b4_sleep_pins_a>;
+ cd-gpios = <&gpiob 7 (GPIO_ACTIVE_LOW | GPIO_PULL_UP)>;
+ disable-wp;
+ st,neg-edge;
+ bus-width = <4>;
+ vmmc-supply = <&v3v3>;
+ status = "okay";
+};
+
+&uart4 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart4_pins_a>;
+ status = "okay";
+};
+
