Add a device tree and a defconfig for the Ingenic X1830 based
YSH & ATIL CU Neo board.
Tested-by: 周正 (Zhou Zheng) <sernia.zhou@xxxxxxxxxxx>
Signed-off-by: 周琰杰 (Zhou Yanjie) <zhouyanjie@xxxxxxxxxxxxxx>
---
Notes:
v1->v2:
1.Add DT node for LED.
2.Update defconfig for LED.
v2->v3:
Adjust the order of nodes according to the
corresponding address value.
v3->v4:
No change.
arch/mips/boot/dts/ingenic/Makefile | 1 +
arch/mips/boot/dts/ingenic/cu1830-neo.dts | 168 ++++++++++++++++++++++++++++++
arch/mips/configs/cu1830-neo_defconfig | 123 ++++++++++++++++++++++
arch/mips/jz4740/Kconfig | 4 +
4 files changed, 296 insertions(+)
create mode 100644 arch/mips/boot/dts/ingenic/cu1830-neo.dts
create mode 100644 arch/mips/configs/cu1830-neo_defconfig
diff --git a/arch/mips/boot/dts/ingenic/Makefile b/arch/mips/boot/dts/ingenic/Makefile
index e1654291a7b0..c33434fad007 100644
--- a/arch/mips/boot/dts/ingenic/Makefile
+++ b/arch/mips/boot/dts/ingenic/Makefile
@@ -3,5 +3,6 @@ dtb-$(CONFIG_JZ4740_QI_LB60) += qi_lb60.dtb
dtb-$(CONFIG_JZ4770_GCW0) += gcw0.dtb
dtb-$(CONFIG_JZ4780_CI20) += ci20.dtb
dtb-$(CONFIG_X1000_CU1000_NEO) += cu1000-neo.dtb
+dtb-$(CONFIG_X1830_CU1830_NEO) += cu1830-neo.dtb
obj-$(CONFIG_BUILTIN_DTB) += $(addsuffix .o, $(dtb-y))
diff --git a/arch/mips/boot/dts/ingenic/cu1830-neo.dts b/arch/mips/boot/dts/ingenic/cu1830-neo.dts
new file mode 100644
index 000000000000..640f96c00d63
--- /dev/null
+++ b/arch/mips/boot/dts/ingenic/cu1830-neo.dts
@@ -0,0 +1,168 @@
+// SPDX-License-Identifier: GPL-2.0
+/dts-v1/;
+
+#include "x1830.dtsi"
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/clock/ingenic,tcu.h>
+#include <dt-bindings/interrupt-controller/irq.h>
+
+/ {
+ compatible = "yna,cu1830-neo", "ingenic,x1830";
+ model = "YSH & ATIL General Board CU1830-Neo";
+
+ aliases {
+ serial1 = &uart1;
+ };
+
+ chosen {
+ stdout-path = "serial1:115200n8";
+ };
+
+ memory {
+ device_type = "memory";
+ reg = <0x0 0x08000000>;
+ };
+
+ leds {
+ compatible = "gpio-leds";
+ led-0 {
+ gpios = <&gpc 17 GPIO_ACTIVE_HIGH>;
+ linux,default-trigger = "mmc0";
+ };
+ };
+
+ wlan_pwrseq: msc1-pwrseq {
+ compatible = "mmc-pwrseq-simple";
+
+ reset-gpios = <&gpc 13 GPIO_ACTIVE_LOW>;
+ post-power-on-delay-ms = <200>;
+ };
+};
+
+&exclk {
+ clock-frequency = <24000000>;
+};
+
+&tcu {
+ /* 1500 kHz for the system timer and clocksource */
+ assigned-clocks = <&tcu TCU_CLK_TIMER0>, <&tcu TCU_CLK_TIMER2>;
+ assigned-clock-rates = <1500000>, <1500000>;
+
+ /* Use channel #0 for the system timer channel #2 for the clocksource */
+ ingenic,pwm-channels-mask = <0xfa>;
+};
+
+&uart1 {
+ status = "okay";
+
+ pinctrl-names = "default";
+ pinctrl-0 = <&pins_uart1>;
+};
+
+&i2c0 {
+ status = "okay";
+
+ clock-frequency = <400000>;
+
+ pinctrl-names = "default";
+ pinctrl-0 = <&pins_i2c0>;
+
+ ads7830: adc@48 {
+ compatible = "ti,ads7830";
+ reg = <0x48>;
+ };
+};
+
+&msc0 {
+ status = "okay";
+
+ bus-width = <4>;
+ max-frequency = <50000000>;
+
+ pinctrl-names = "default";
+ pinctrl-0 = <&pins_msc0>;
+
+ non-removable;
+};
+
+&msc1 {
+ status = "okay";
+
+ #address-cells = <1>;
+ #size-cells = <0>;
+ bus-width = <4>;
+ max-frequency = <50000000>;
+
+ pinctrl-names = "default";
+ pinctrl-0 = <&pins_msc1>;
+
+ non-removable;
+
+ mmc-pwrseq = <&wlan_pwrseq>;
+
+ ap6212a: wifi@1 {
+ compatible = "brcm,bcm4329-fmac";
+ reg = <1>;
+
+ interrupt-parent = <&gpc>;
+ interrupts = <25 IRQ_TYPE_EDGE_FALLING>;
+ interrupt-names = "host-wake";
+
+ brcm,drive-strength = <10>;
+ };
+};
+
+&mac {
+ status = "okay";
+
+ phy-mode = "rmii";
+ phy-handle = <&ip101gr>;
+
+ pinctrl-names = "default";
+ pinctrl-0 = <&pins_mac>;
+
+ snps,reset-gpio = <&gpb 28 GPIO_ACTIVE_LOW>; /* PB28 */
+ snps,reset-active-low;
+ snps,reset-delays-us = <0 10000 30000>;
+};
+
+&mdio {
+ status = "okay";
+
+ ip101gr: ethernet-phy@0 {
+ compatible = "ethernet-phy-id0243.0c54", "ethernet-phy-ieee802.3-c22";
+ reg = <0>;
+ };
+};
+
+&pinctrl {
+ pins_uart1: uart1 {
+ function = "uart1";
+ groups = "uart1-data";
+ bias-pull-up;
+ };
+
+ pins_i2c0: i2c0 {
+ function = "i2c0";
+ groups = "i2c0-data";
+ bias-pull-up;
+ };
+
+ pins_msc0: msc0 {
+ function = "mmc0";
+ groups = "mmc0-1bit", "mmc0-4bit";
+ bias-disable;
+ };
+
+ pins_msc1: msc1 {
+ function = "mmc1";
+ groups = "mmc1-1bit", "mmc1-4bit";
+ bias-disable;
+ };
+
+ pins_mac: mac {
+ function = "mac";
+ groups = "mac";
+ bias-disable;
+ };
+};
diff --git a/arch/mips/configs/cu1830-neo_defconfig b/arch/mips/configs/cu1830-neo_defconfig
new file mode 100644
index 000000000000..cbfb62900273
--- /dev/null
+++ b/arch/mips/configs/cu1830-neo_defconfig
@@ -0,0 +1,123 @@
+CONFIG_LOCALVERSION_AUTO=y
+CONFIG_KERNEL_GZIP=y
+CONFIG_SYSVIPC=y
+CONFIG_NO_HZ_IDLE=y
+CONFIG_HIGH_RES_TIMERS=y
+CONFIG_PREEMPT=y
+CONFIG_IKCONFIG=y
+CONFIG_IKCONFIG_PROC=y
+CONFIG_LOG_BUF_SHIFT=14
+CONFIG_CGROUPS=y
+CONFIG_MEMCG=y
+CONFIG_MEMCG_KMEM=y
+CONFIG_CGROUP_SCHED=y
+CONFIG_CGROUP_FREEZER=y
+CONFIG_CGROUP_DEVICE=y
+CONFIG_CGROUP_CPUACCT=y
+CONFIG_NAMESPACES=y
+CONFIG_USER_NS=y
+CONFIG_CC_OPTIMIZE_FOR_SIZE=y
+CONFIG_KALLSYMS_ALL=y
+CONFIG_EMBEDDED=y
+# CONFIG_VM_EVENT_COUNTERS is not set
+# CONFIG_COMPAT_BRK is not set
+CONFIG_SLAB=y
+CONFIG_MACH_INGENIC=y
+CONFIG_X1830_CU1830_NEO=y
+CONFIG_HIGHMEM=y
+CONFIG_HZ_100=y
+# CONFIG_SECCOMP is not set
+# CONFIG_SUSPEND is not set
+# CONFIG_CORE_DUMP_DEFAULT_ELF_HEADERS is not set
+# CONFIG_COMPACTION is not set
+CONFIG_CMA=y
+CONFIG_CMA_AREAS=7
+CONFIG_NET=y
+CONFIG_PACKET=y
+CONFIG_UNIX=y
+CONFIG_INET=y
+CONFIG_CFG80211=y
+CONFIG_UEVENT_HELPER=y
+CONFIG_UEVENT_HELPER_PATH="/sbin/hotplug"
+CONFIG_DEVTMPFS=y
+# CONFIG_FW_LOADER is not set
+# CONFIG_ALLOW_DEV_COREDUMP is not set
+CONFIG_MD=y
+CONFIG_BLK_DEV_MD=y
+CONFIG_BLK_DEV_DM=y
+CONFIG_NETDEVICES=y
+CONFIG_STMMAC_ETH=y
+CONFIG_ICPLUS_PHY=y
+CONFIG_BRCMFMAC=y
+# CONFIG_INPUT_MOUSEDEV is not set
+# CONFIG_INPUT_KEYBOARD is not set
+# CONFIG_INPUT_MOUSE is not set
+# CONFIG_SERIO is not set
+CONFIG_VT_HW_CONSOLE_BINDING=y
+CONFIG_LEGACY_PTY_COUNT=2
+CONFIG_SERIAL_EARLYCON=y
+CONFIG_SERIAL_8250=y
+CONFIG_SERIAL_8250_CONSOLE=y
+CONFIG_SERIAL_8250_NR_UARTS=2
+CONFIG_SERIAL_8250_RUNTIME_UARTS=2
+CONFIG_SERIAL_8250_INGENIC=y
+CONFIG_SERIAL_OF_PLATFORM=y
+# CONFIG_HW_RANDOM is not set
+CONFIG_I2C=y
+CONFIG_I2C_JZ4780=y
+CONFIG_GPIO_SYSFS=y
+CONFIG_SENSORS_ADS7828=y
+CONFIG_WATCHDOG=y
+CONFIG_JZ4740_WDT=y
+# CONFIG_LCD_CLASS_DEVICE is not set
+# CONFIG_BACKLIGHT_CLASS_DEVICE is not set
+# CONFIG_VGA_CONSOLE is not set
+# CONFIG_HID is not set
+# CONFIG_USB_SUPPORT is not set
+CONFIG_MMC=y
+CONFIG_MMC_JZ4740=y
+CONFIG_NEW_LEDS=y
+CONFIG_LEDS_CLASS=y
+CONFIG_LEDS_GPIO=y
+CONFIG_LEDS_TRIGGERS=y
+CONFIG_RTC_CLASS=y
+CONFIG_RTC_DRV_JZ4740=y
+CONFIG_DMADEVICES=y
+CONFIG_DMA_JZ4780=y
+# CONFIG_IOMMU_SUPPORT is not set
+CONFIG_NVMEM=y
+CONFIG_NVMEM_SYSFS=y
+CONFIG_EXT4_FS=y
+# CONFIG_DNOTIFY is not set
+CONFIG_AUTOFS_FS=y
+CONFIG_PROC_KCORE=y
+# CONFIG_PROC_PAGE_MONITOR is not set
+CONFIG_TMPFS=y
+CONFIG_CONFIGFS_FS=y
+CONFIG_NFS_FS=y
+CONFIG_NLS=y
+CONFIG_NLS_CODEPAGE_936=y
+CONFIG_NLS_CODEPAGE_950=y
+CONFIG_NLS_ASCII=y
+CONFIG_NLS_ISO8859_1=y
+CONFIG_NLS_UTF8=y
+CONFIG_CRYPTO_ECHAINIV=y
+CONFIG_CRYPTO_AES=y
+CONFIG_CRYPTO_DEFLATE=y
+CONFIG_CRYPTO_LZO=y
+CONFIG_PRINTK_TIME=y
+CONFIG_CONSOLE_LOGLEVEL_DEFAULT=15
+CONFIG_CONSOLE_LOGLEVEL_QUIET=15
+CONFIG_MESSAGE_LOGLEVEL_DEFAULT=7
+CONFIG_DEBUG_INFO=y
+CONFIG_STRIP_ASM_SYMS=y
+CONFIG_DEBUG_FS=y
+CONFIG_MAGIC_SYSRQ=y
+CONFIG_PANIC_ON_OOPS=y
+CONFIG_PANIC_TIMEOUT=10
+# CONFIG_SCHED_DEBUG is not set
+# CONFIG_DEBUG_PREEMPT is not set
+CONFIG_STACKTRACE=y
+# CONFIG_FTRACE is not set
+CONFIG_CMDLINE_BOOL=y
+CONFIG_CMDLINE="earlycon clk_ignore_unused"
diff --git a/arch/mips/jz4740/Kconfig b/arch/mips/jz4740/Kconfig
index cd0ddb52da99..6c065dcaeff8 100644
--- a/arch/mips/jz4740/Kconfig
+++ b/arch/mips/jz4740/Kconfig
@@ -27,6 +27,10 @@ config X1000_CU1000_NEO
bool "YSH & ATIL CU1000 Module with Neo backplane"
select MACH_X1000
+config X1830_CU1830_NEO
+ bool "YSH & ATIL CU1830 Module with Neo backplane"
+ select MACH_X1830
+
endchoice
config MACH_JZ4740
--
2.11.0
