The SADC component in JZ47xx SoCs provides support for touchscreen
operations (pen position and pen down pressure) in single-ended and
differential modes.
The touchscreen component of SADC takes a significant time to stabilize
after first receiving the clock and a delay of 50ms has been empirically
proven to be a safe value before data sampling can begin.
Of the known hardware to use this controller, GCW Zero and Anbernic RG-350
utilize the touchscreen mode by having their joystick(s) attached to the
X/Y positive/negative input pins.
JZ4770 and later SoCs introduce a low-level command feature. With it, up
to 32 commands can be programmed, each one corresponding to a sampling
job. It allows to change the low-voltage reference, the high-voltage
reference, have them connected to VCC, GND, or one of the X-/X+ or Y-/Y+
pins.
This patch introduces support for 6 stream-capable channels:
- channel #0 samples X+/GND
- channel #1 samples Y+/GND
- channel #2 samples X-/GND
- channel #3 samples Y-/GND
- channel #4 samples X+/X-
- channel #5 samples Y+/Y-
Being able to sample X-/GND and Y-/GND is useful on some devices, where
one joystick is connected to the X+/Y+ pins, and a second joystick is
connected to the X-/Y- pins.
All the boards which probe this driver have the interrupt provided from
Device Tree, with no need to handle a case where the IRQ was not provided.
Co-developed-by: Paul Cercueil <paul@xxxxxxxxxxxxxxx>
Signed-off-by: Paul Cercueil <paul@xxxxxxxxxxxxxxx>
Signed-off-by: Artur Rojek <contact@xxxxxxxxxxxxxx>
---
Changes:
v2: - improve description of the touchscreen mode,
- get rid of the unneeded kfifo,
- drop IIO_BUFFER_CB from Kconfig,
- remove extended names from the touchscreen channels
v3: remove unneeded `linux/iio/kfifo_buf.h` include
v4: clarify irq provider source in the patch description
v5: no change
v6: - correct the spelling of Device Tree and IRQ in commit message
- don't omit trailing commas from initializer lists
- error check `clk_enable`
- remove redundant `dev_err` from `platform_get_irq` error check
v7: no change
v8: add support for ADCMD low-level command feature
drivers/iio/adc/Kconfig | 1 +
drivers/iio/adc/ingenic-adc.c | 250 +++++++++++++++++++++++++++++++++-
2 files changed, 249 insertions(+), 2 deletions(-)
diff --git a/drivers/iio/adc/Kconfig b/drivers/iio/adc/Kconfig
index ff3569635ce0..5b57437cef75 100644
--- a/drivers/iio/adc/Kconfig
+++ b/drivers/iio/adc/Kconfig
@@ -500,6 +500,7 @@ config INA2XX_ADC
config INGENIC_ADC
tristate "Ingenic JZ47xx SoCs ADC driver"
depends on MIPS || COMPILE_TEST
+ select IIO_BUFFER
help
Say yes here to build support for the Ingenic JZ47xx SoCs ADC unit.
diff --git a/drivers/iio/adc/ingenic-adc.c b/drivers/iio/adc/ingenic-adc.c
index 0233a9055c86..976aea46fede 100644
--- a/drivers/iio/adc/ingenic-adc.c
+++ b/drivers/iio/adc/ingenic-adc.c
@@ -8,7 +8,9 @@
#include <dt-bindings/iio/adc/ingenic,adc.h>
#include <linux/clk.h>
+#include <linux/iio/buffer.h>
#include <linux/iio/iio.h>
+#include <linux/interrupt.h>
#include <linux/io.h>
#include <linux/iopoll.h>
#include <linux/kernel.h>
@@ -20,19 +22,46 @@
#define JZ_ADC_REG_CFG 0x04
#define JZ_ADC_REG_CTRL 0x08
#define JZ_ADC_REG_STATUS 0x0c
+#define JZ_ADC_REG_ADSAME 0x10
+#define JZ_ADC_REG_ADWAIT 0x14
#define JZ_ADC_REG_ADTCH 0x18
#define JZ_ADC_REG_ADBDAT 0x1c
#define JZ_ADC_REG_ADSDAT 0x20
+#define JZ_ADC_REG_ADCMD 0x24
#define JZ_ADC_REG_ADCLK 0x28
#define JZ_ADC_REG_ENABLE_PD BIT(7)
#define JZ_ADC_REG_CFG_AUX_MD (BIT(0) | BIT(1))
#define JZ_ADC_REG_CFG_BAT_MD BIT(4)
+#define JZ_ADC_REG_CFG_SAMPLE_NUM(n) ((n) << 10)
+#define JZ_ADC_REG_CFG_PULL_UP(n) ((n) << 16)
+#define JZ_ADC_REG_CFG_CMD_SEL BIT(22)
+#define JZ_ADC_REG_CFG_TOUCH_OPS_MASK (BIT(31) | GENMASK(23, 10))
#define JZ_ADC_REG_ADCLK_CLKDIV_LSB 0
#define JZ4725B_ADC_REG_ADCLK_CLKDIV10US_LSB 16
#define JZ4770_ADC_REG_ADCLK_CLKDIV10US_LSB 8
#define JZ4770_ADC_REG_ADCLK_CLKDIVMS_LSB 16
+#define JZ_ADC_REG_ADCMD_YNADC BIT(7)
+#define JZ_ADC_REG_ADCMD_YPADC BIT(8)
+#define JZ_ADC_REG_ADCMD_XNADC BIT(9)
+#define JZ_ADC_REG_ADCMD_XPADC BIT(10)
+#define JZ_ADC_REG_ADCMD_VREFPYP BIT(11)
+#define JZ_ADC_REG_ADCMD_VREFPXP BIT(12)
+#define JZ_ADC_REG_ADCMD_VREFPXN BIT(13)
+#define JZ_ADC_REG_ADCMD_VREFPAUX BIT(14)
+#define JZ_ADC_REG_ADCMD_VREFPVDD33 BIT(15)
+#define JZ_ADC_REG_ADCMD_VREFNYN BIT(16)
+#define JZ_ADC_REG_ADCMD_VREFNXP BIT(17)
+#define JZ_ADC_REG_ADCMD_VREFNXN BIT(18)
+#define JZ_ADC_REG_ADCMD_VREFAUX BIT(19)
+#define JZ_ADC_REG_ADCMD_YNGRU BIT(20)
+#define JZ_ADC_REG_ADCMD_XNGRU BIT(21)
+#define JZ_ADC_REG_ADCMD_XPGRU BIT(22)
+#define JZ_ADC_REG_ADCMD_YPSUP BIT(23)
+#define JZ_ADC_REG_ADCMD_XNSUP BIT(24)
+#define JZ_ADC_REG_ADCMD_XPSUP BIT(25)
+
#define JZ_ADC_AUX_VREF 3300
#define JZ_ADC_AUX_VREF_BITS 12
#define JZ_ADC_BATTERY_LOW_VREF 2500
@@ -44,6 +73,14 @@
#define JZ4770_ADC_BATTERY_VREF 6600
#define JZ4770_ADC_BATTERY_VREF_BITS 12
+#define JZ_ADC_IRQ_AUX BIT(0)
+#define JZ_ADC_IRQ_BATTERY BIT(1)
+#define JZ_ADC_IRQ_TOUCH BIT(2)
+#define JZ_ADC_IRQ_PEN_DOWN BIT(3)
+#define JZ_ADC_IRQ_PEN_UP BIT(4)
+#define JZ_ADC_IRQ_PEN_DOWN_SLEEP BIT(5)
+#define JZ_ADC_IRQ_SLEEP BIT(7)
+
struct ingenic_adc;
struct ingenic_adc_soc_data {
@@ -69,6 +106,61 @@ struct ingenic_adc {
bool low_vref_mode;
};
+static void ingenic_adc_set_adcmd(struct iio_dev *iio_dev, unsigned long mask)
+{
+ struct ingenic_adc *adc = iio_priv(iio_dev);
+
+ mutex_lock(&adc->lock);
+
+ /* Init ADCMD */
+ readl(adc->base + JZ_ADC_REG_ADCMD);
+
+ if (mask & 0x3) {
+ /* Second channel (INGENIC_ADC_TOUCH_YP): sample YP vs. GND */
+ writel(JZ_ADC_REG_ADCMD_XNGRU
+ | JZ_ADC_REG_ADCMD_VREFNXN | JZ_ADC_REG_ADCMD_VREFPVDD33
+ | JZ_ADC_REG_ADCMD_YPADC,
+ adc->base + JZ_ADC_REG_ADCMD);
+
+ /* First channel (INGENIC_ADC_TOUCH_XP): sample XP vs. GND */
+ writel(JZ_ADC_REG_ADCMD_YNGRU
+ | JZ_ADC_REG_ADCMD_VREFNYN | JZ_ADC_REG_ADCMD_VREFPVDD33
+ | JZ_ADC_REG_ADCMD_XPADC,
+ adc->base + JZ_ADC_REG_ADCMD);
+ }
+
+ if (mask & 0xc) {
+ /* Fourth channel (INGENIC_ADC_TOUCH_YN): sample YN vs. GND */
+ writel(JZ_ADC_REG_ADCMD_XNGRU
+ | JZ_ADC_REG_ADCMD_VREFNXN | JZ_ADC_REG_ADCMD_VREFPVDD33
+ | JZ_ADC_REG_ADCMD_YNADC,
+ adc->base + JZ_ADC_REG_ADCMD);
+
+ /* Third channel (INGENIC_ADC_TOUCH_XN): sample XN vs. GND */
+ writel(JZ_ADC_REG_ADCMD_YNGRU
+ | JZ_ADC_REG_ADCMD_VREFNYN | JZ_ADC_REG_ADCMD_VREFPVDD33
+ | JZ_ADC_REG_ADCMD_XNADC,
+ adc->base + JZ_ADC_REG_ADCMD);
+ }
+
+ if (mask & 0x30) {
+ /* Sixth channel (INGENIC_ADC_TOUCH_YD): sample YP vs. YN */
+ writel(JZ_ADC_REG_ADCMD_VREFNYN | JZ_ADC_REG_ADCMD_VREFPVDD33
+ | JZ_ADC_REG_ADCMD_YPADC,
+ adc->base + JZ_ADC_REG_ADCMD);
+
+ /* Fifth channel (INGENIC_ADC_TOUCH_XD): sample XP vs. XN */
+ writel(JZ_ADC_REG_ADCMD_VREFNXN | JZ_ADC_REG_ADCMD_VREFPVDD33
+ | JZ_ADC_REG_ADCMD_XPADC,
+ adc->base + JZ_ADC_REG_ADCMD);
+ }
+
+ /* We're done */
+ writel(0, adc->base + JZ_ADC_REG_ADCMD);
+
+ mutex_unlock(&adc->lock);
+}
+
static void ingenic_adc_set_config(struct ingenic_adc *adc,
uint32_t mask,
uint32_t val)
@@ -288,6 +380,72 @@ static const struct iio_chan_spec jz4740_channels[] = {
};
static const struct iio_chan_spec jz4770_channels[] = {
+ {
+ .type = IIO_POSITIONRELATIVE,
+ .indexed = 1,
+ .channel = INGENIC_ADC_TOUCH_XP,
+ .scan_index = 0,
+ .scan_type = {
+ .sign = 'u',
+ .realbits = 12,
+ .storagebits = 16,
+ },
+ },
+ {
+ .type = IIO_POSITIONRELATIVE,
+ .indexed = 1,
+ .channel = INGENIC_ADC_TOUCH_YP,
+ .scan_index = 1,
+ .scan_type = {
+ .sign = 'u',
+ .realbits = 12,
+ .storagebits = 16,
+ },
+ },
+ {
+ .type = IIO_POSITIONRELATIVE,
+ .indexed = 1,
+ .channel = INGENIC_ADC_TOUCH_XN,
+ .scan_index = 2,
+ .scan_type = {
+ .sign = 'u',
+ .realbits = 12,
+ .storagebits = 16,
+ },
+ },
+ {
+ .type = IIO_POSITIONRELATIVE,
+ .indexed = 1,
+ .channel = INGENIC_ADC_TOUCH_YN,
+ .scan_index = 3,
+ .scan_type = {
+ .sign = 'u',
+ .realbits = 12,
+ .storagebits = 16,
+ },
+ },
+ {
+ .type = IIO_POSITIONRELATIVE,
+ .indexed = 1,
+ .channel = INGENIC_ADC_TOUCH_XD,
+ .scan_index = 4,
+ .scan_type = {
+ .sign = 'u',
+ .realbits = 12,
+ .storagebits = 16,
+ },
+ },
+ {
+ .type = IIO_POSITIONRELATIVE,
+ .indexed = 1,
+ .channel = INGENIC_ADC_TOUCH_YD,
+ .scan_index = 5,
+ .scan_type = {
+ .sign = 'u',
+ .realbits = 12,
+ .storagebits = 16,
+ },
+ },
{
.extend_name = "aux",
.type = IIO_VOLTAGE,
@@ -490,13 +648,89 @@ static const struct iio_info ingenic_adc_info = {
.of_xlate = ingenic_adc_of_xlate,
};
+static int ingenic_adc_buffer_enable(struct iio_dev *iio_dev)
+{
+ struct ingenic_adc *adc = iio_priv(iio_dev);
+ int ret;
+
+ ret = clk_enable(adc->clk);
+ if (ret) {
+ dev_err(iio_dev->dev.parent, "Failed to enable clock: %d\n",
+ ret);
+ return ret;
+ }
+
+ /* It takes significant time for the touchscreen hw to stabilize. */
+ msleep(50);
+ ingenic_adc_set_config(adc, JZ_ADC_REG_CFG_TOUCH_OPS_MASK,
+ JZ_ADC_REG_CFG_SAMPLE_NUM(4) |
+ JZ_ADC_REG_CFG_PULL_UP(4));
+
+ writew(80, adc->base + JZ_ADC_REG_ADWAIT);
+ writew(2, adc->base + JZ_ADC_REG_ADSAME);
+ writeb((u8)~JZ_ADC_IRQ_TOUCH, adc->base + JZ_ADC_REG_CTRL);
+ writel(0, adc->base + JZ_ADC_REG_ADTCH);
+
+ ingenic_adc_set_config(adc, JZ_ADC_REG_CFG_CMD_SEL,
+ JZ_ADC_REG_CFG_CMD_SEL);
+ ingenic_adc_set_adcmd(iio_dev, iio_dev->active_scan_mask[0]);
+
+ ingenic_adc_enable(adc, 2, true);
+
+ return 0;
+}
+
+static int ingenic_adc_buffer_disable(struct iio_dev *iio_dev)
+{
+ struct ingenic_adc *adc = iio_priv(iio_dev);
+
+ ingenic_adc_enable(adc, 2, false);
+
+ ingenic_adc_set_config(adc, JZ_ADC_REG_CFG_CMD_SEL, 0);
+
+ writeb(0xff, adc->base + JZ_ADC_REG_CTRL);
+ writeb(0xff, adc->base + JZ_ADC_REG_STATUS);
+ ingenic_adc_set_config(adc, JZ_ADC_REG_CFG_TOUCH_OPS_MASK, 0);
+ writew(0, adc->base + JZ_ADC_REG_ADSAME);
+ writew(0, adc->base + JZ_ADC_REG_ADWAIT);
+ clk_disable(adc->clk);
+
+ return 0;
+}
+
+static const struct iio_buffer_setup_ops ingenic_buffer_setup_ops = {
+ .postenable = &ingenic_adc_buffer_enable,
+ .predisable = &ingenic_adc_buffer_disable
+};
+
+static irqreturn_t ingenic_adc_irq(int irq, void *data)
+{
+ struct iio_dev *iio_dev = data;
+ struct ingenic_adc *adc = iio_priv(iio_dev);
+ unsigned long mask = iio_dev->active_scan_mask[0];
+ unsigned int i;
+ u32 tdat[3];
+
+ for (i = 0; i < ARRAY_SIZE(tdat); mask >>= 2, i++) {
+ if (mask & 0x3)
+ tdat[i] = readl(adc->base + JZ_ADC_REG_ADTCH);
+ else
+ tdat[i] = 0;
+ }
+
+ iio_push_to_buffers(iio_dev, tdat);
+ writeb(JZ_ADC_IRQ_TOUCH, adc->base + JZ_ADC_REG_STATUS);
+
+ return IRQ_HANDLED;
+}
+
static int ingenic_adc_probe(struct platform_device *pdev)
{
struct device *dev = &pdev->dev;
struct iio_dev *iio_dev;
struct ingenic_adc *adc;
const struct ingenic_adc_soc_data *soc_data;
- int ret;
+ int irq, ret;
soc_data = device_get_match_data(dev);
if (!soc_data)
@@ -511,6 +745,17 @@ static int ingenic_adc_probe(struct platform_device *pdev)
mutex_init(&adc->aux_lock);
adc->soc_data = soc_data;
+ irq = platform_get_irq(pdev, 0);
+ if (irq < 0)
+ return irq;
+
+ ret = devm_request_irq(dev, irq, ingenic_adc_irq, 0,
+ dev_name(dev), iio_dev);
+ if (ret < 0) {
+ dev_err(dev, "Failed to request irq: %d\n", ret);
+ return ret;
+ }
+
adc->base = devm_platform_ioremap_resource(pdev, 0);
if (IS_ERR(adc->base))
return PTR_ERR(adc->base);
@@ -550,7 +795,8 @@ static int ingenic_adc_probe(struct platform_device *pdev)
iio_dev->dev.parent = dev;
iio_dev->name = "jz-adc";
- iio_dev->modes = INDIO_DIRECT_MODE;
+ iio_dev->modes = INDIO_DIRECT_MODE | INDIO_BUFFER_SOFTWARE;
+ iio_dev->setup_ops = &ingenic_buffer_setup_ops;
iio_dev->channels = soc_data->channels;
iio_dev->num_channels = soc_data->num_channels;
iio_dev->info = &ingenic_adc_info;
--
2.27.0
