On Wed, Jul 01, 2020 at 06:29:27PM +0200, Ondrej Jirman wrote:
> From: Icenowy Zheng <icenowy@xxxxxxx>
>
> PinePhone uses PWM backlight and a XBD599 LCD panel over DSI for
> display.
>
> Backlight levels curve was optimized by Martijn Braam using a
> lux meter.
>
> Add its device nodes.
>
> Signed-off-by: Icenowy Zheng <icenowy@xxxxxxx>
> Signed-off-by: Martijn Braam <martijn@xxxxxxxxx>
> Signed-off-by: Ondrej Jirman <megous@xxxxxxxxxx>
> Acked-by: Linus Walleij <linus.walleij@xxxxxxxxxx>
> ---
> .../allwinner/sun50i-a64-pinephone-1.1.dts | 19 ++++++++++
> .../dts/allwinner/sun50i-a64-pinephone.dtsi | 35 +++++++++++++++++++
> 2 files changed, 54 insertions(+)
>
> diff --git a/arch/arm64/boot/dts/allwinner/sun50i-a64-pinephone-1.1.dts b/arch/arm64/boot/dts/allwinner/sun50i-a64-pinephone-1.1.dts
> index 06a775c41664..3e99a87e9ce5 100644
> --- a/arch/arm64/boot/dts/allwinner/sun50i-a64-pinephone-1.1.dts
> +++ b/arch/arm64/boot/dts/allwinner/sun50i-a64-pinephone-1.1.dts
> @@ -9,3 +9,22 @@ / {
> model = "Pine64 PinePhone Braveheart (1.1)";
> compatible = "pine64,pinephone-1.1", "allwinner,sun50i-a64";
> };
> +
> +&backlight {
> + power-supply = <®_ldo_io0>;
> + /*
> + * PWM backlight circuit on this PinePhone revision was changed since
> + * 1.0, and the lowest PWM duty cycle that doesn't lead to backlight
> + * being off is around 20%. Duty cycle for the lowest brightness level
> + * also varries quite a bit between individual boards, so the lowest
> + * value here was chosen as a safe default.
> + */
> + brightness-levels = <
> + 774 793 814 842
> + 882 935 1003 1088
> + 1192 1316 1462 1633
> + 1830 2054 2309 2596
> + 2916 3271 3664 4096>;
> + num-interpolated-steps = <50>;
> + default-brightness-level = <400>;
> +};
> diff --git a/arch/arm64/boot/dts/allwinner/sun50i-a64-pinephone.dtsi b/arch/arm64/boot/dts/allwinner/sun50i-a64-pinephone.dtsi
> index cefda145c3c9..85a7aa5efd32 100644
> --- a/arch/arm64/boot/dts/allwinner/sun50i-a64-pinephone.dtsi
> +++ b/arch/arm64/boot/dts/allwinner/sun50i-a64-pinephone.dtsi
> @@ -16,6 +16,13 @@ aliases {
> serial0 = &uart0;
> };
>
> + backlight: backlight {
> + compatible = "pwm-backlight";
> + pwms = <&r_pwm 0 50000 PWM_POLARITY_INVERTED>;
> + enable-gpios = <&pio 7 10 GPIO_ACTIVE_HIGH>; /* PH10 */
> + /* Backlight configuration differs per PinePhone revision. */
> + };
> +
> chosen {
> stdout-path = "serial0:115200n8";
> };
> @@ -84,6 +91,30 @@ &dai {
> status = "okay";
> };
>
> +&de {
> + status = "okay";
> +};
> +
> +&dphy {
> + status = "okay";
> +};
> +
> +&dsi {
> + vcc-dsi-supply = <®_dldo1>;
> + #address-cells = <1>;
> + #size-cells = <0>;
> + status = "okay";
If you're about to send a new version, you can remove #address-cells and
#size-cells too, they're already set in the DTSI.
Maxime
Attachment:
signature.asc
Description: PGP signature
