On Thu, 25 Jun 2020, Masahiro Yamada wrote: > On Thu, Jun 25, 2020 at 3:16 AM Lee Jones <lee.jones@xxxxxxxxxx> wrote: > > > > On Thu, 25 Jun 2020, Masahiro Yamada wrote: > > > > > On Tue, Jun 23, 2020 at 9:24 PM Lee Jones <lee.jones@xxxxxxxxxx> wrote: > > > > > > > > On Tue, 23 Jun 2020, Masahiro Yamada wrote: > > > > > > > > > 'make ARCH=arm dtbs_check' emits the following warning: > > > > > > > > > > support-card@1,1f00000: $nodename:0: 'support-card@1,1f00000' does not match '^(bus|soc|axi|ahb|apb)(@[0-9a-f]+)?$' > > > > > > > > > > Maybe, simple-mfd could be a better fit for this device. > > > > > > > > The two should be equivalent. > > > > > > Yes, I know. > > > That's why I can change "simple-bus" to "simple-mfd" > > > with no risk. > > > > > > The difference is schema-check. > > > > > > The node name for "simple-bus" is checked by 'make dtbs_check'. > > > > > > See this code: > > > https://github.com/robherring/dt-schema/blob/v2020.05/schemas/simple-bus.yaml#L17 > > > > > > Even if I rename the node, it does not accept the > > > unit name '1,1f00000' > > > > > > > What do you mean by "maybe"? Does this squash the warning? > > > > > > "maybe" means I am not quite sure > > > which compatible is a better fit > > > to describe this device. > > > > > > As mentioned above, simple-bus and simple-mfd > > > are interchangeable from a driver point of view. > > > > > > This add-on board is integrated with various peripherals > > > such as 16550a serial, smsc9115 ether etc. > > > The address-decode is implemented in a CPLD device. > > > It has chip selects and local addresses, which are mapped to > > > the parent. > > > > > > It can be either simple-bus or simple-mfd, I think. > > > > > > > > > dt-schema checks the node name of simple-bus. > > > Currently, there is no check for simple-mfd. > > > > > > So, I think this patch is an easy solution > > > to fix the warning. > > > > Yes, looking at the documentation it seems as though 'simple-mfd' > > would be a better fit. Is the device a single IP with various > > different functions? > > Not an IP. > > This is a small board that consists of > a CPLD + ethernet controller + serial controller + LED, etc. Then simple MFD does not seem like a good fit. Neither does 'simple-bus'. What is it you're trying to describe in the device hierarchy? > > > Rob is in Cc. Please add comments if any. > > > > > > > Isn't the issue caused by the ','? > > > > > > Right. > > > > > > The node name of simple-bus > > > must meet the regular expression: > > > "^(bus|soc|axi|ahb|apb)(@[0-9a-f]+)?$" > > > > > > > > > Even if I rename the node > > > "support-card@1,1f00000" > > > to "bus@1,1f00000", the warning is still > > > displayed due to ',' > > > > > > "1,1f00000" means > > > the address 0x01f00000 of chip select 1. > > > > Is this an officially accepted format? > > I am not sure if it is official. > > Rob said the data fields should be separated by commas. > https://www.spinics.net/lists/devicetree/msg201565.html Are you sure he doesn't mean in the 'reg' property. Rather than the node-name@NNNNNNNN syntax. BTW, I think the error you link to above is related to the node-name@NNNNNNNN not matching the value listed in the 'reg' property. -- Lee Jones [李琼斯] Senior Technical Lead - Developer Services Linaro.org │ Open source software for Arm SoCs Follow Linaro: Facebook | Twitter | Blog
