[PATCH 5/6] arm64: dts: qcom: sm8250: Add remoteprocs

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



Add remoteproc nodes for the audio, compute and sensor cores, define
glink for each one and enable them on the MTP with appropriate firmware
defined.

Signed-off-by: Bjorn Andersson <bjorn.andersson@xxxxxxxxxx>
---
 arch/arm64/boot/dts/qcom/sm8250-mtp.dts |  15 +++
 arch/arm64/boot/dts/qcom/sm8250.dtsi    | 116 ++++++++++++++++++++++++
 2 files changed, 131 insertions(+)

diff --git a/arch/arm64/boot/dts/qcom/sm8250-mtp.dts b/arch/arm64/boot/dts/qcom/sm8250-mtp.dts
index 63d259931c4d..6894f8490dae 100644
--- a/arch/arm64/boot/dts/qcom/sm8250-mtp.dts
+++ b/arch/arm64/boot/dts/qcom/sm8250-mtp.dts
@@ -55,6 +55,11 @@ vreg_s6c_0p88: smpc6-regulator {
 	};
 };
 
+&adsp {
+	status = "okay";
+	firmware-name = "qcom/sm8250/adsp.mbn";
+};
+
 &apps_rsc {
 	pm8150-rpmh-regulators {
 		compatible = "qcom,pm8150-rpmh-regulators";
@@ -348,10 +353,20 @@ vreg_l7f_1p8: ldo7 {
 	};
 };
 
+&cdsp {
+	status = "okay";
+	firmware-name = "qcom/sm8250/cdsp.mbn";
+};
+
 &qupv3_id_1 {
 	status = "okay";
 };
 
+&slpi {
+	status = "okay";
+	firmware-name = "qcom/sm8250/slpi.mbn";
+};
+
 &tlmm {
 	gpio-reserved-ranges = <28 4>, <40 4>;
 };
diff --git a/arch/arm64/boot/dts/qcom/sm8250.dtsi b/arch/arm64/boot/dts/qcom/sm8250.dtsi
index 364d9a798673..a21299b9c62f 100644
--- a/arch/arm64/boot/dts/qcom/sm8250.dtsi
+++ b/arch/arm64/boot/dts/qcom/sm8250.dtsi
@@ -1052,6 +1052,83 @@ tcsr_mutex_regs: syscon@1f40000 {
 			reg = <0x0 0x01f40000 0x0 0x40000>;
 		};
 
+		slpi: remoteproc@5c00000 {
+			compatible = "qcom,sm8250-slpi-pas";
+			reg = <0 0x05c00000 0 0x4000>;
+
+			interrupts-extended = <&pdc 9 IRQ_TYPE_LEVEL_HIGH>,
+					      <&smp2p_slpi_in 0 IRQ_TYPE_EDGE_RISING>,
+					      <&smp2p_slpi_in 1 IRQ_TYPE_EDGE_RISING>,
+					      <&smp2p_slpi_in 2 IRQ_TYPE_EDGE_RISING>,
+					      <&smp2p_slpi_in 3 IRQ_TYPE_EDGE_RISING>;
+			interrupt-names = "wdog", "fatal", "ready",
+					  "handover", "stop-ack";
+
+			clocks = <&rpmhcc RPMH_CXO_CLK>;
+			clock-names = "xo";
+
+			power-domains = <&aoss_qmp AOSS_QMP_LS_SLPI>,
+					<&rpmhpd SM8250_LCX>,
+					<&rpmhpd SM8250_LMX>;
+			power-domain-names = "load_state", "lcx", "lmx";
+
+			memory-region = <&slpi_mem>;
+
+			qcom,smem-states = <&smp2p_slpi_out 0>;
+			qcom,smem-state-names = "stop";
+
+			status = "disabled";
+
+			glink-edge {
+				interrupts-extended = <&ipcc IPCC_CLIENT_SLPI
+							     IPCC_MPROC_SIGNAL_GLINK_QMP
+							     IRQ_TYPE_EDGE_RISING>;
+				mboxes = <&ipcc IPCC_CLIENT_SLPI
+						IPCC_MPROC_SIGNAL_GLINK_QMP>;
+
+				label = "lpass";
+				qcom,remote-pid = <3>;
+			};
+		};
+
+		cdsp: remoteproc@8300000 {
+			compatible = "qcom,sm8250-cdsp-pas";
+			reg = <0 0x08300000 0 0x10000>;
+
+			interrupts-extended = <&intc GIC_SPI 578 IRQ_TYPE_LEVEL_HIGH>,
+					      <&smp2p_cdsp_in 0 IRQ_TYPE_EDGE_RISING>,
+					      <&smp2p_cdsp_in 1 IRQ_TYPE_EDGE_RISING>,
+					      <&smp2p_cdsp_in 2 IRQ_TYPE_EDGE_RISING>,
+					      <&smp2p_cdsp_in 3 IRQ_TYPE_EDGE_RISING>;
+			interrupt-names = "wdog", "fatal", "ready",
+					  "handover", "stop-ack";
+
+			clocks = <&rpmhcc RPMH_CXO_CLK>;
+			clock-names = "xo";
+
+			power-domains = <&aoss_qmp AOSS_QMP_LS_CDSP>,
+					<&rpmhpd SM8250_CX>;
+			power-domain-names = "load_state", "cx";
+
+			memory-region = <&cdsp_mem>;
+
+			qcom,smem-states = <&smp2p_cdsp_out 0>;
+			qcom,smem-state-names = "stop";
+
+			status = "disabled";
+
+			glink-edge {
+				interrupts-extended = <&ipcc IPCC_CLIENT_CDSP
+							     IPCC_MPROC_SIGNAL_GLINK_QMP
+							     IRQ_TYPE_EDGE_RISING>;
+				mboxes = <&ipcc IPCC_CLIENT_CDSP
+						IPCC_MPROC_SIGNAL_GLINK_QMP>;
+
+				label = "lpass";
+				qcom,remote-pid = <5>;
+			};
+		};
+
 		pdc: interrupt-controller@b220000 {
 			compatible = "qcom,sm8250-pdc", "qcom,pdc";
 			reg = <0 0x0b220000 0 0x30000>, <0 0x17c000f0 0 0x60>;
@@ -1668,6 +1745,45 @@ config {
 			};
 		};
 
+		adsp: remoteproc@17300000 {
+			compatible = "qcom,sm8250-adsp-pas";
+			reg = <0 0x17300000 0 0x100>;
+
+			interrupts-extended = <&pdc 6 IRQ_TYPE_LEVEL_HIGH>,
+					      <&smp2p_adsp_in 0 IRQ_TYPE_EDGE_RISING>,
+					      <&smp2p_adsp_in 1 IRQ_TYPE_EDGE_RISING>,
+					      <&smp2p_adsp_in 2 IRQ_TYPE_EDGE_RISING>,
+					      <&smp2p_adsp_in 3 IRQ_TYPE_EDGE_RISING>;
+			interrupt-names = "wdog", "fatal", "ready",
+					  "handover", "stop-ack";
+
+			clocks = <&rpmhcc RPMH_CXO_CLK>;
+			clock-names = "xo";
+
+			power-domains = <&aoss_qmp AOSS_QMP_LS_LPASS>,
+					<&rpmhpd SM8250_LCX>,
+					<&rpmhpd SM8250_LMX>;
+			power-domain-names = "load_state", "lcx", "lmx";
+
+			memory-region = <&adsp_mem>;
+
+			qcom,smem-states = <&smp2p_adsp_out 0>;
+			qcom,smem-state-names = "stop";
+
+			status = "disabled";
+
+			glink-edge {
+				interrupts-extended = <&ipcc IPCC_CLIENT_LPASS
+							     IPCC_MPROC_SIGNAL_GLINK_QMP
+							     IRQ_TYPE_EDGE_RISING>;
+				mboxes = <&ipcc IPCC_CLIENT_LPASS
+						IPCC_MPROC_SIGNAL_GLINK_QMP>;
+
+				label = "lpass";
+				qcom,remote-pid = <2>;
+			};
+		};
+
 		intc: interrupt-controller@17a00000 {
 			compatible = "arm,gic-v3";
 			#interrupt-cells = <3>;
-- 
2.26.2




[Index of Archives]     [Device Tree Compilter]     [Device Tree Spec]     [Linux Driver Backports]     [Video for Linux]     [Linux USB Devel]     [Linux PCI Devel]     [Linux Audio Users]     [Linux Kernel]     [Linux SCSI]     [XFree86]     [Yosemite Backpacking]


  Powered by Linux