On Sun, 21 Jun 2020 00:42:16 +0200
Jonathan Neuschäfer <j.neuschaefer@xxxxxxx> wrote:
> The Netronix embedded controller as found in Kobo Aura and Tolino Shine
> supports one PWM channel, which is used to control the frontlight
> brightness on these devices.
>
> Known problems:
> - `make dt_binding_check` shows the following warnings:
> Documentation/devicetree/bindings/mfd/netronix,ntxec.example.dts:49.17-42:
> Warning (pwms_property): /example-0/backlight:pwms: cell 2 is not a
> phandle reference
> Documentation/devicetree/bindings/mfd/netronix,ntxec.example.dts:49.17-42:
> Warning (pwms_property): /example-0/backlight:pwms: Could not get
> phandle node for (cell 2)
>
In the tolino sources in ./drivers/misc/ntx-misc.c I find this line
if(4==gptHWCFG->m_val.bFL_PWM) {
No idea what it does but I would expect to have a kind of translation to
a dt property?
> Signed-off-by: Jonathan Neuschäfer <j.neuschaefer@xxxxxxx>
> ---
> .../bindings/mfd/netronix,ntxec.yaml | 13 ++++++++
> .../bindings/pwm/netronix,ntxec-pwm.yaml | 33 +++++++++++++++++++
> 2 files changed, 46 insertions(+)
> create mode 100644 Documentation/devicetree/bindings/pwm/netronix,ntxec-pwm.yaml
>
> diff --git a/Documentation/devicetree/bindings/mfd/netronix,ntxec.yaml b/Documentation/devicetree/bindings/mfd/netronix,ntxec.yaml
> index 596df460f98eb..6562c41c5a9a9 100644
> --- a/Documentation/devicetree/bindings/mfd/netronix,ntxec.yaml
> +++ b/Documentation/devicetree/bindings/mfd/netronix,ntxec.yaml
> @@ -31,6 +31,9 @@ properties:
> description:
> The EC can signal interrupts via a GPIO line
>
> + pwm:
> + $ref: ../pwm/netronix,ntxec-pwm.yaml
> +
> required:
> - compatible
> - reg
> @@ -53,5 +56,15 @@ examples:
> interrupts = <11 IRQ_TYPE_EDGE_FALLING>;
> interrupt-controller;
> #interrupt-cells = <1>;
> +
> + ec_pwm: pwm {
> + compatible = "netronix,ntxec-pwm";
> + #pwm-cells = <1>;
shouldn't that be 2?
> + };
> };
> };
> +
> + backlight {
> + compatible = "pwm-backlight";
> + pwms = <&ec_pwm 0 50000>;
since you have 2 values after the &ec_pwm
> + };
> diff --git a/Documentation/devicetree/bindings/pwm/netronix,ntxec-pwm.yaml b/Documentation/devicetree/bindings/pwm/netronix,ntxec-pwm.yaml
> new file mode 100644
> index 0000000000000..1dc1b1aba081c
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/pwm/netronix,ntxec-pwm.yaml
> @@ -0,0 +1,33 @@
> +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
> +%YAML 1.2
> +---
> +$id: http://devicetree.org/schemas/pwm/netronix,ntxec-pwm.yaml#
> +$schema: http://devicetree.org/meta-schemas/core.yaml#
> +
> +title: PWM functionality in Netronix embedded controller
> +
> +maintainers:
> + - Jonathan Neuschäfer <j.neuschaefer@xxxxxxx>
> +
> +description: |
> + See also Documentation/devicetree/bindings/mfd/netronix,ntxec.yaml
> +
> + The Netronix EC contains PWM functionality, which is usually used to drive
> + the backlight LED.
> +
> + The following PWM channels are supported:
> + - 0: The PWM channel controlled by registers 0xa1-0xa7
> +
> +allOf:
> + - $ref: pwm.yaml#
> +
> +properties:
> + compatible:
> + const: netronix,ntxec-pwm
> +
> + "#pwm-cells":
> + const: 1
shouln't that be 2?
> +
> +required:
> + - compatible
> + - "#pwm-cells"
> --
> 2.27.0
>
>
Regards,
Andreas
