Re: [PATCH/RFC 1/5] dt-bindings: net: renesas,ravb: Document internal clock delay properties

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



Hi Sergei,

On Sat, Jun 20, 2020 at 8:16 PM Sergei Shtylyov
<sergei.shtylyov@xxxxxxxxxxxxxxxxxx> wrote:
> On 06/19/2020 10:15 PM, Geert Uytterhoeven wrote:
> > Some EtherAVB variants support internal clock delay configuration, which
> > can add larger delays than the delays that are typically supported by
> > the PHY (using an "rgmii-*id" PHY mode, and/or "[rt]xc-skew-ps"
> > properties).
> >
> > Add properties for configuring the internal MAC delays.
> > These properties are mandatory, even when specified as zero, to
> > distinguish between old and new DTBs.
> >
> > Update the example accordingly.
> >
> > Signed-off-by: Geert Uytterhoeven <geert+renesas@xxxxxxxxx>

> > --- a/Documentation/devicetree/bindings/net/renesas,ravb.txt
> > +++ b/Documentation/devicetree/bindings/net/renesas,ravb.txt
> > @@ -64,6 +64,18 @@ Optional properties:
> >                        AVB_LINK signal.
> >  - renesas,ether-link-active-low: boolean, specify when the AVB_LINK signal is
> >                                active-low instead of normal active-high.
> > +- renesas,rxc-delay-ps: Internal RX clock delay.
> > +                     This property is mandatory and valid only on R-Car Gen3
> > +                     and RZ/G2 SoCs.
> > +                     Valid values are 0 and 1800.
> > +                     A non-zero value is allowed only if phy-mode = "rgmii".
> > +                     Zero is not supported on R-Car D3.
>
>    Hm, where did you see about the D3 limitation?

R-Car Gen3 Hardware User's Manual, Section 50.2.7 ("AVB-DMAC Product
Specific Register (APSR)"), "RDM" bit:

    For R-Car D3, delayed mode is only available

> > +- renesas,txc-delay-ps: Internal TX clock delay.
> > +                     This property is mandatory and valid only on R-Car H3,
> > +                     M3-W, M3-W+, M3-N, V3M, and V3H, and RZ/G2M and RZ/G2N.
> > +                     Valid values are 0 and 2000.
> > +                     A non-zero value is allowed only if phy-mode = "rgmii".
> > +                     Zero is not supported on R-Car V3H.
>
>   Same question about V3H here...

Same section, "TDM" bit:

    For R-Car V3H, delayed mode is only available.

> > @@ -105,8 +117,10 @@ Example:
> >                                 "ch24";
> >               clocks = <&cpg CPG_MOD 812>;
> >               power-domains = <&cpg>;
> > -             phy-mode = "rgmii-id";
> > +             phy-mode = "rgmii";
> >               phy-handle = <&phy0>;
> > +             renesas,rxc-delay-ps = <0>;
>
>    Mhm, zero RX delay in RGMII-ID mode?

Please ignore the actual contents of the old example.  It was based on a
very old DTS, which has received several fixes in the mean time.

Should have written:

    Update the (bogus) example accordingly.

Gr{oetje,eeting}s,

                        Geert

-- 
Geert Uytterhoeven -- There's lots of Linux beyond ia32 -- geert@xxxxxxxxxxxxxx

In personal conversations with technical people, I call myself a hacker. But
when I'm talking to journalists I just say "programmer" or something like that.
                                -- Linus Torvalds



[Index of Archives]     [Device Tree Compilter]     [Device Tree Spec]     [Linux Driver Backports]     [Video for Linux]     [Linux USB Devel]     [Linux PCI Devel]     [Linux Audio Users]     [Linux Kernel]     [Linux SCSI]     [XFree86]     [Yosemite Backpacking]


  Powered by Linux